SPDIF and cs46xx ?
Hello,
I have also been attempting to use Dolby Digital passthru with my Turtle
Beach Santa Cruz. Unfortunately I have not yet been successful.
For these tests I am using todays (March 16) CVS of alsa-kernel, alsa-driver
and alsa-lib. For xine I'm using xine-lib-1-beta8, compiled with todays ALSA CVS.
In my tests I have had two different results:
1) No sound
2) A clicking sound (described by another user as "cards in a bike") For the times I get this sound, it's normally about 4-6 beats-per-second (or so), but if I unmute "IEC958 Input" it nearly doubles (about 8-12 beats-per-second).
------------------
Here's the relevant console output from xine when I start playing a movie:
liba52:No accelerated IMDCT transform foundaudio_alsa_out: Audio Device name = iec958:AES0=0x6,AES1=0x82,AES2=0x0,AES3=0x2audio_alsa_out: Number of channels = 2
audio_alsa_out:open pause_resume=0
stream : PLAYBACK
access : RW_INTERLEAVED
format : S16_LE
subformat : STD
channels : 2
rate : 48000
exact rate : 48000 (48000/1)
msbits : 16buffer_size : 16384period_size : 512period_time : 10666tick_time : 10000tstamp_mode : NONEperiod_step : 1sleep_min : 0avail_min : 512xfer_align : 1start_threshold : 512stop_threshold : 16384silence_threshold: 0silence_size : 0
boundary : 1073741824start_mode: DATAxrun_mode: STOPtstamp_mode: NONEperiod_step: 1sleep_min: 0avail_min: 512xfer_align: 1silence_threshold: 0silence_size: 0
boundary: 1073741824
metronom: fixing sound card drift by -1544 pts audio_alsa_out:write:BAD STATE, state = 1
audio_alsa_out:write:BAD STATE2, state = 1, going to try XRUN audio_alsa_out:write:BAD STATE, state = 1
audio_alsa_out:write:BAD STATE2, state = 1, going to try XRUN
------------------
Here's my syslog output when I start and stop a AC3 stream (with either xine
or ac3dec [-C/-P]):
Mar 16 12:54:17 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/cs46xx_lib.c: 1430: open raw iec958 channel Mar 16 12:54:17 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/dsp_spos_scb_ lib.c:226: cs46xx_dsp_proc_free_scb_desc: freeing PCMSerialInput_II Mar 16 12:54:17 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/dsp_spos_scb_ lib.c:226: cs46xx_dsp_proc_free_scb_desc: freeing AsynchFGTxSCB Mar 16 12:54:17 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/dsp_spos_scb_ lib.c:290: dsp_spos: creating SCB <AsynchFGTxSCB> Mar 16 12:54:17 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/dsp_spos_scb_ lib.c:1178: IEC958 pass through Mar 16 12:54:17 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/dsp_spos_scb_ lib.c:1243: dsp_spos: creating SRC "SrcTask_SCB0" Mar 16 12:54:17 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/dsp_spos_scb_ lib.c:597: dsp_spos: setting SrcTask_SCB0 rate to 48000 Mar 16 12:54:17 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/dsp_spos_scb_ lib.c:290: dsp_spos: creating SCB <SrcTask_SCB0> Mar 16 12:54:17 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/dsp_spos_scb_ lib.c:1268: dsp_spos: creating PCM "PCMReader_SCB0" (5) Mar 16 12:54:17 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/dsp_spos_scb_ lib.c:290: dsp_spos: creating SCB <PCMReader_SCB0> Mar 16 12:54:17 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/cs46xx_lib.c: 1001: period_size (2048), periods (32) buffer_size(65536) Mar 16 12:54:27 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/cs46xx_lib.c: 1446: close raw iec958 channel Mar 16 12:54:27 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/dsp_spos_scb_ lib.c:226: cs46xx_dsp_proc_free_scb_desc: freeing PCMReader_SCB0 Mar 16 12:54:27 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/dsp_spos_scb_ lib.c:226: cs46xx_dsp_proc_free_scb_desc: freeing SrcTask_SCB0 Mar 16 12:54:27 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/dsp_spos_scb_ lib.c:226: cs46xx_dsp_proc_free_scb_desc: freeing AsynchFGTxSCB Mar 16 12:54:27 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/dsp_spos_scb_ lib.c:290: dsp_spos: creating SCB <AsynchFGTxSCB> Mar 16 12:54:27 darkstar kernel: ALSA ../../alsa-kernel/pci/cs46xx/dsp_spos_scb_
lib.c:290: dsp_spos: creating SCB <PCMSerialInput_II>
------------------
TIA for any advice or help with this. And thanks for all your great work,
Benny.
-- Peter Heatwole
"Murphy was just a well known pessimist."
-------------------------------------------------------
This SF.net email is sponsored by:Crypto Challenge is now open! Get cracking and register here for some mind boggling fun and the chance of winning an Apple iPod:
http://ads.sourceforge.net/cgi-bin/redirect.pl?thaw0031en
Quoted 7 lines
2) A clicking sound (described by another user as "cards in a bike") For the times I get this sound, it's normally about 4-6 beats-per-second (or so), but if I unmute "IEC958 Input" it nearly doubles (about 8-12 beats-per-second).
Sounds like your receiver don't detect the AC3 stream, and inteprets it
like PCM instead. There can be many reasons why this hapen, right now I can mention:
- The AC3 is altered in some how, DSP applies gain's, roundings, while procesing stream (operation that are audible while playing PCM, and probably improbes sound), then when the data reach the receiver it's not detected as AC3 anymore. In the current cs46xx driver there's a special treatment for 48khz streams through IEC958, to prevent the DSP process the stream in any way.
- The magic status bit's, I'm not sure if the current implementation in the cs46xx that
set's the IEC958 is correct. I have not found any way to verify ...
/Benny
-------------------------------------------------------
This SF.net email is sponsored by:Crypto Challenge is now open! Get cracking and register here for some mind boggling fun and the chance of winning an Apple iPod:
http://ads.sourceforge.net/cgi-bin/redirect.pl?thaw0031en
Quoted 4 lines · Benny Sjostrand
Sounds like your receiver don't detect the AC3 stream, and inteprets it like PCM instead. There can be many reasons why this hapen, right now I can mention:
- The AC3 is altered in some how, DSP applies gain's, roundings, while
Quoted 8 lines
procesing stream (operation that are audible while playing PCM, and probably improbes sound), then when the data reach the receiver it's not detected as AC3 anymore. In the current cs46xx driver there's a special treatment for 48khz streams through IEC958, to prevent the DSP process the stream in any way.
- The magic status bit's, I'm not sure if the current implementation in the cs46xx that
set's the IEC958 is correct. I have not found any way to verify ...
And is there any hope of any enhancement?
I "need" the SPDIF of my Digifire 7.1 to be able to use the bitstreamout plugin of VDR made by Dr. Werner Fink
(https://sourceforge.net/projects/bitstreamout/) because as he wrote the SPDIF out of my DVB card is not "good":
"As long as the hardware on the DVB cards are not able to put the 16bit none audio PCM data stream into a 32bit none audio S/P-DIF transport stream all receivers which uses the bit flags of the S/P-DIF transport stream for identifying none audio loose. All S/P-DIF data get from the DVB card to not have the none audio bit set. AFAIK this is a hardware bug (or better this is the information I've got from TT) ..."
But when I try the plugin I got:
Mar 29 15:15:17 localhost vdr[9090]: S/P-DIF: Period size not available: Invalid argument Mar 29 15:15:17 localhost vdr[9090]: S/P-DIF: unable to establish BitStreamOut for none audio PCM Mar 29 15:15:17 localhost vdr[9090]: REPLAY: can't open spdif interface
I am using CVS of driver/lib/utils from yesterday...
Any suggestion?
Thank you very much,
Grégoire
________________________________________________________________
http://ulima.unil.ch/greg ICQ:16624071 mailto:[email protected]
-------------------------------------------------------
This SF.net email is sponsored by:
The Definitive IT and Networking Event. Be There! NetWorld+Interop Las Vegas 2003 -- Register today!
http://ads.sourceforge.net/cgi-bin/redirect.pl?keyn0001en
Quoted 16 lines
And is there any hope of any enhancement?
I "need" the SPDIF of my Digifire 7.1 to be able to use the bitstreamout plugin of VDR made by Dr. Werner Fink
(https://sourceforge.net/projects/bitstreamout/) because as he wrote the SPDIF out of my DVB card is not "good":"As long as the hardware on the DVB cards are not able to put the 16bit none audio PCM data stream into a 32bit none audio S/P-DIF transport stream all receivers which uses the bit flags of the S/P-DIF transport stream for identifying none audio loose. All S/P-DIF data get from the DVB card to not have the none audio bit set. AFAIK this is a hardware bug (or better this is the information I've got from TT) ..."
Quoted 7 lines
But when I try the plugin I got:
Mar 29 15:15:17 localhost vdr[9090]: S/P-DIF: Period size not available: Invalid argument Mar 29 15:15:17 localhost vdr[9090]: S/P-DIF: unable to establish BitStreamOut for none audio PCM Mar 29 15:15:17 localhost vdr[9090]: REPLAY: can't open spdif interface
Seems like a user application problem to me. The cs46xx driver just support a limited set of period-size configurations, that's a limitation in the HW. Then it's up to the application to handle it (I guess)
I've managed to make AC3 and DTS through SPDIF work witth OGLE and Xine, I dont see any reason why it would'nt work with any other application, at least you should get further than: "S/P-DIF: Period size not available: Invalid argument" then when you've managed to open the device and write data to it maybe there will apear other unknown problems ...
/Benny
-------------------------------------------------------
This SF.net email is sponsored by:
The Definitive IT and Networking Event. Be There! NetWorld+Interop Las Vegas 2003 -- Register today!
http://ads.sourceforge.net/cgi-bin/redirect.pl?keyn0001en
Quoted 8 lines · Benny Sjostrand
Seems like a user application problem to me. The cs46xx driver just support a limited set of period-size configurations, that's a limitation in the HW. Then it's up to the application to handle it (I guess) I've managed to make AC3 and DTS through SPDIF work witth OGLE and Xine, I dont see any reason why it would'nt work with any other application, at least you should get further than: "S/P-DIF: Period size not
available: Invalid argument" then when you've managed to open the device and write data to it maybe there will apear other unknown problems ...
Well, I think there are two problem, the first one is the limited set of period-size configurations which the bitstream plugin should take care of, but the real reason I repost what Dr. Werner Fink wrote in the [email protected] mailing list was because he spoke exactly about a problem we are a lots to have with the cs46xx driver :-( Also found relative to DVB (AC3overDVB from Stefan Huelswitt,
http://www.muempf.de/down/vdr-1.1.26-AC3overDVB-0.1.4.diff.gz ) which contains in the README.AC3overDVB:
If your receiver doesn't detect the encapsulated stream (at the beginning of replay in general) you will hear the digital data played as PCM data. It's a spiky noise. Don't turn up the volume too much, or the speakers may be damaged. You have been warned!
And afterthat I post the answer from Dr. Werner Fink:
As long as the hardware on the DVB cards are not able to put the 16bit none audio PCM data stream into a 32bit none audio S/P-DIF transport stream all receivers which uses the bit flags of the S/P-DIF transport stream for identifying none audio loose. All S/P-DIF data get from the DVB card to not have the none audio bit set. AFAIK this is a hardware bug (or better this is the information I've got from TT) ...
And what I think is that we have exactly the same problem with the cs46xx driver: I couldn't have a real 5.1 with any tools under linux and cs46xx (ac3dec,ac3play,mplayer,xine), in fact I couldn't alsa hear the sound from the CD using the SPDIF...
I think we need a fix for some receiver that don't detect the encapsulated stream...
Thank you very much,
Grégoire
________________________________________________________________
http://ulima.unil.ch/greg ICQ:16624071 mailto:[email protected]
-------------------------------------------------------
This SF.net email is sponsored by:
The Definitive IT and Networking Event. Be There! NetWorld+Interop Las Vegas 2003 -- Register today!
http://ads.sourceforge.net/cgi-bin/redirect.pl?keyn0001en
Quoted 12 lines
Well, I think there are two problem, the first one is the limited set of period-size configurations which the bitstream plugin should take care of, but the real reason I repost what Dr. Werner Fink wrote in the [email protected] mailing list was because he spoke exactly about a problem we are a lots to have with the cs46xx driver :-( Also found relative to DVB (AC3overDVB from Stefan Huelswitt,
http://www.muempf.de/down/vdr-1.1.26-AC3overDVB-0.1.4.diff.gz ) which contains in the README.AC3overDVB:
About the period sizes there'e nothing we can do in the driver, as this is a HW limitation.
(However it's possible to implement Scatter/Gather DMA support for the cs46xx driver, then maybe there's more posibilies to variate the period size, but that's not going to happen in a near future ...)
Quoted 7 lines
If your receiver doesn't detect the encapsulated stream (at the beginning of replay in general) you will hear the digital data played as PCM data. It's a spiky noise. Don't turn up the volume too much, or the speakers may be damaged. You have been warned!
I think that the problem with the current cs46xx driver could be the status bits in the IEC958 stream that is not set correctly. Some receivers seems to ignore the status bits and detects the format looking into the stream instead, other receivers may look into the status bits to detect if it's PCM audio, or digital data. So it's posible that AC3 DTS, etc work's OK with thoose receivers that just ignores the content of the status bits, which I think is the case of my Harmon Kardoon receiver.
/Benny
-------------------------------------------------------
This SF.net email is sponsored by:
The Definitive IT and Networking Event. Be There! NetWorld+Interop Las Vegas 2003 -- Register today!
http://ads.sourceforge.net/cgi-bin/redirect.pl?keyn0001en
Quoted 5 lines · Benny Sjostrand
About the period sizes there'e nothing we can do in the driver, as this is a HW limitation.
(However it's possible to implement Scatter/Gather DMA support for the cs46xx driver, then maybe there's more posibilies to variate the period size, but that's not going to happen in a near future ...)
OK, I hope Dr. Werner Fink could work with this limitation ;-)
Quoted 4 lines
I think that the problem with the current cs46xx driver could be the status bits
in the IEC958 stream that is not set correctly. Some receivers seems to ignore
Quoted 8 lines
the status bits and detects the format looking into the stream instead, other receivers
may look into the status bits to detect if it's PCM audio, or digital data. So it's posible that AC3 DTS, etc work's OK with thoose receivers that just ignores
the content of the status bits, which I think is the case of my Harmon Kardoon
receiver.
Great, even with my bad english and I was understood !!! Is there any hope to fix this issue?
Thank you very much,
Grégoire
________________________________________________________________
http://ulima.unil.ch/greg ICQ:16624071 mailto:[email protected]
-------------------------------------------------------
This SF.net email is sponsored by:
The Definitive IT and Networking Event. Be There! NetWorld+Interop Las Vegas 2003 -- Register today!
http://ads.sourceforge.net/cgi-bin/redirect.pl?keyn0001en
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 2 lines
If mmap is used in the bitstreamout plugin the period size is 1024 bytes or 256 stereo PCM samples. Does this work with the cs46xx hw?
Yes, 1024 _bytes_ period size should be supported by block DMA. The following period sizes are supported: 2048, 1024, 512, 256, 64, 32 bytes.
Quoted 3 lines
See my former mail how this could be done if the hardware allows direct access to the S/P-DIF out (e.g. raw out with 96kHz for effective 49kHz sample frequence of the PCM data).
The current cs46xx driver only supports raw 48khz output. I'm not sure, but maybe it's possible to set the SPDIF controller to 96khz. I need to check this.
/Benny
-------------------------------------------------------
This SF.net email is sponsored by: ValueWeb:
Dedicated Hosting for just $79/mo with 500 GB of bandwidth! No other company gives more support or power for your dedicated server
http://click.atdmt.com/AFF/go/sdnxxaff00300020aff/direct/01/
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 10 lines · Dr. Werner Fink
Hmmm ... I've put some lines into
cmipci.cto support setting of the seconf/third status bits within the 2*192 status bits of the S/P-DIF stream for supporting none audio data PCM streams (with this it should also possible to support 20 or 24 bits per PCM word) -> SeeUSE_AES_IEC958cpp macro incmipci.c.IMHO this way should be possibel for all sound chips which are not able to provide a hardware setup of the status bits of the S/P-DIF stream but able to put out raw data (e.g. 32 bit S/P-DIF words) with doubled sample clock onto the S/P-DIF out plug.
Hello again,
sorry to ask again :-(
I have just installed latest alsa CVS of drivers,lib and utils and still get a:
pr 4 13:37:43 localhost vdr[20035]: S/P-DIF: Period size not available: Invalid argument
Apr 4 13:37:43 localhost vdr[20035]: S/P-DIF: unable to establish BitStreamOut for none audio PCM Apr 4 13:37:43 localhost vdr[20035]: REPLAY: can't open spdif interface
Should I change anything anywhere?
Or buy a card with cmipci? (Well I like the Digifire 7.1 I have now, which has also an integrated Firewire...).
Thank you very much,
Grégoire
________________________________________________________________
http://ulima.unil.ch/greg ICQ:16624071 mailto:[email protected]
-------------------------------------------------------
This SF.net email is sponsored by: ValueWeb:
Dedicated Hosting for just $79/mo with 500 GB of bandwidth! No other company gives more support or power for your dedicated server
http://click.atdmt.com/AFF/go/sdnxxaff00300020aff/direct/01/
Quoted 6 lines
sorry to ask again :-(
I have just installed latest alsa CVS of drivers,lib and utils and still get a:
Quoted 8 lines
pr 4 13:37:43 localhost vdr[20035]: S/P-DIF: Period size not available: Invalid argument
Apr 4 13:37:43 localhost vdr[20035]: S/P-DIF: unable to establish BitStreamOut for none audio PCM Apr 4 13:37:43 localhost vdr[20035]: REPLAY: can't open spdif interfaceShould I change anything anywhere?
Or buy a card with cmipci? (Well I like the Digifire 7.1 I have now, which has also an integrated Firewire...).
I would like to get to the bottom of this problem.
Let's try figure out exactly which lines of code produces thoose messages: "S/P-DIF: Period size not available: Invalid argument" and "S/P-DIF: unable to establish BitStreamOut for none audio PCM"
/Benny
-------------------------------------------------------
This SF.net email is sponsored by: ValueWeb: Dedicated Hosting for just $79/mo with 500 GB of bandwidth! No other company gives more support or power for your dedicated server
http://click.atdmt.com/AFF/go/sdnxxaff00300020aff/direct/01/
Quoted 4 lines · Benny Sjostrand
I would like to get to the bottom of this problem.
Let's try figure out exactly which lines of code produces thoose
messages: "S/P-DIF: Period size not available: Invalid argument" and "S/P-DIF: unable to establish BitStreamOut for none audio PCM"
The whole archive could be found under
http://prdownloads.sourceforge.net/sourceforge/bitstreamout/
And I have put the file spdif.c under
http://ulima.unil.ch/greg/linux/spdif.c
In this file, there are the errors messages, unfortunately it's far too complicated for my basic programming knowledge ;-)
Thank you very much,
Grégoire
________________________________________________________________
http://ulima.unil.ch/greg ICQ:16624071 mailto:[email protected]
-------------------------------------------------------
This SF.net email is sponsored by: ValueWeb:
Dedicated Hosting for just $79/mo with 500 GB of bandwidth! No other company gives more support or power for your dedicated server
http://click.atdmt.com/AFF/go/sdnxxaff00300020aff/direct/01/
Quoted 5 lines
The whole archive could be found under
http://prdownloads.sourceforge.net/sourceforge/bitstreamout/
Quoted 8 lines
And I have put the file
spdif.cunder
http://ulima.unil.ch/greg/linux/spdif.cIn this file, there are the errors messages, unfortunately it's far too
complicated for my basic programming knowledge ;-)
The snd-cs46xx driver should support the period size specified by the program (1024 bytes right ?), so next.
Did you load the snd-cs46xx module with the mmap_valid=1 parameter ??
/Benny
-------------------------------------------------------
This SF.net email is sponsored by: ValueWeb: Dedicated Hosting for just $79/mo with 500 GB of bandwidth! No other company gives more support or power for your dedicated server
http://click.atdmt.com/AFF/go/sdnxxaff00300020aff/direct/01/
Quoted 4 lines · Benny Sjostrand
The snd-cs46xx driver should support the period size specified by the program (1024 bytes right ?), so next.
Did you load the snd-cs46xx module with the mmap_valid=1 parameter ??
??? No, the only reference I found about this option is regarding OSS
(http://alsa.opensrc.org/index.php?page=cs46xx) and I never thought it was of any use for me...
I have added
options snd-cs46xx mmap_valid=1
to my /etc/modules.conf and done an /etc/init.d/alsa restart without any change, so I try a /etc/init.d/alsa stop and checked that's there is no more alsa modules loaded at all and do a
modprobe snd-cs46xx mmap_valid=1
Or is there another way?
Thank you very much,
Grégoire
________________________________________________________________
http://ulima.unil.ch/greg ICQ:16624071 mailto:[email protected]
-------------------------------------------------------
This SF.net email is sponsored by: ValueWeb:
Dedicated Hosting for just $79/mo with 500 GB of bandwidth! No other company gives more support or power for your dedicated server
http://click.atdmt.com/AFF/go/sdnxxaff00300020aff/direct/01/
Quoted 14 lines
??? No, the only reference I found about this option is regarding OSS
(http://alsa.opensrc.org/index.php?page=cs46xx) and I never thought it was of any use for me...
I have added
options snd-cs46xx mmap_valid=1
to my/etc/modules.confand done an/etc/init.d/alsarestart without any change, so I try a/etc/init.d/alsastop and checked that's there is no more alsa modules loaded at all and do a
modprobe snd-cs46xx mmap_valid=1
Adding it to modules.conf should be enough, that does not seems to be the problem anyway. So:
if ((err = snd_pcm_hw_params_set_period_size(out, hwparams,MMAP_BURST, 0)) < 0) {
!! esyslog("S/P-DIF: Period size not available: %s", snd_strerror(err));
period_size = 0;
goto err_out;
}
// function returns less than 0 on error or greater than 0
if ((err = snd_pcm_hw_params_set_buffer_size_near(out, hwparams,
burst_size*periods)) < 0) {
esyslog("S/P-DIF: Buffer size not available: %s",
snd_strerror(err));
goto err_out;
}
} else {
frag = 1;
// function returns less than 0 on error or greater than 0
if ((err = snd_pcm_hw_params_set_period_size(out, hwparams,
burst_size, 0)) < 0) {
!! esyslog("S/P-DIF: Period size not available: %s", snd_strerror(err));
period_size = 0;
goto err_out;
}It seems to be the snd_pcm_hw_params_set_period_size(...) that fails, it seems to be two possible places where this function is called.
I guess there's a constraint in the cs46xx driver which does not allow the desired period settings, maybe someone with more knowledge about the alsa-lib can help us figure out what ??
/Benny
-------------------------------------------------------
This SF.net email is sponsored by: ValueWeb: Dedicated Hosting for just $79/mo with 500 GB of bandwidth! No other company gives more support or power for your dedicated server
http://click.atdmt.com/AFF/go/sdnxxaff00300020aff/direct/01/
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 2 lines · Dr. Werner Fink
Please use mmap way ... see manaul page vdr-bistreamout.5 for more details.
Well, I didn't thought about it :-( I did try to use mmap, and you are totally right, with this option, the error message are gone ;-) Unfortunately all I can hear is a clicking sound (just like with a direct connection with my DVB card) and with what I now know it's not a problem with the bistreamout but with the cs46xx driver!!!
Same problem with ac3play,xine,mplayer...
So I am sorry for having looked for a false problem :-(
Quoted 1 line
You do not need a new card.
But only someone who could solve the SPDIF output of the cs46xx driver...
Thank you very much,
Grégoire
________________________________________________________________
http://ulima.unil.ch/greg ICQ:16624071 mailto:[email protected]
-------------------------------------------------------
This SF.net email is sponsored by: ValueWeb:
Dedicated Hosting for just $79/mo with 500 GB of bandwidth! No other company gives more support or power for your dedicated server
http://click.atdmt.com/AFF/go/sdnxxaff00300020aff/direct/01/