sun7i: a20: Add Bananapi M1 Plus support
Subsystems (2)
PATCH 1/1 sun7i: a20: Add Bananapi M1 Plus support
From: Jagan Teki <[email protected]>
Banana Pi M1 Plus is an open-source single-board computer that adds more connectivity to the classic board using Allwinner A20 SOC.
Bananapi M1-Plus features:
- A20 Dual-core 1.0GHz
- 1 GB DDR3 SDRAM
- MicroSD
- 10/100/1000 Ethernet RJ45
- WiFi b/g/n
- 5V DC Micro USB power-supply
For dts file,
Sync with Linux commit f92ca09("Merge branch 'akpm/master'").
Signed-off-by Jagan Teki <[email protected]>
--- arch/arm/dts/sun7i-a20-bananapi-m1-plus.dts | 91 +++++++++++++++++++++-------- board/sunxi/MAINTAINERS | 5 ++ configs/bananapi_m1_plus_defconfig | 24 ++++++++ 3 files changed, 97 insertions(+), 23 deletions(-) create mode 100644 configs/bananapi_m1_plus_defconfig
arch/arm/dts/sun7i-a20-bananapi-m1-plus.dts +68 -23
@@ -105,6 +105,10 @@ status = "okay"; }; +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + &ehci0 { status = "okay"; };
@@ -132,16 +136,14 @@ status = "okay"; axp209: pmic at 34 { - compatible = "x-powers,axp209"; reg = <0x34>; interrupt-parent = <&nmi_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - - interrupt-controller; - #interrupt-cells = <1>; }; }; +#include "axp209.dtsi" + &ir0 { pinctrl-names = "default"; pinctrl-0 = <&ir0_rx_pins_a>;
@@ -167,10 +169,10 @@ mmc-pwrseq = <&mmc3_pwrseq>; bus-width = <4>; non-removable; - enable-sdio-wakeup; + wakeup-source; status = "okay"; - brcmf: bcrmf at 1 { + brcmf: wifi at 1 { reg = <1>; compatible = "brcm,bcm4329-fmac"; interrupt-parent = <&pio>;
@@ -181,7 +183,7 @@ &mmc3_pins_a { /* AP6210 requires pull-up */ - allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + bias-pull-up; }; &ohci0 {
@@ -192,38 +194,81 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { gmac_power_pin_bpi_m1p: gmac_power_pin at 0 { - allwinner,pins = "PH23"; - allwinner,function = "gpio_out"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + pins = "PH23"; + function = "gpio_out"; }; led_pins_bpi_m1p: led_pins at 0 { - allwinner,pins = "PH24", "PH25"; - allwinner,function = "gpio_out"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + pins = "PH24", "PH25"; + function = "gpio_out"; }; mmc0_cd_pin_bpi_m1p: mmc0_cd_pin at 0 { - allwinner,pins = "PH10"; - allwinner,function = "gpio_in"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + pins = "PH10"; + function = "gpio_in"; + bias-pull-up; }; mmc3_pwrseq_pin_bpi_m1p: mmc3_pwrseq_pin at 0 { - allwinner,pins = "PH22"; - allwinner,function = "gpio_out"; - allwinner,drive = <SUN4I_PINCTRL_10_MA>; - allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + pins = "PH22"; + function = "gpio_out"; }; }; +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-int-dll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_usb0_vbus { + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; status = "okay"; }; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + +&usbphy { + usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_usb0_vbus>; + /* VBUS on usb host ports are tied to DC5V and therefore always on */ + status = "okay"; +};
board/sunxi/MAINTAINERS +5 -0
@@ -118,6 +118,11 @@ M: Paul Kocialkowski <[email protected]> S: Maintained F: configs/Ampe_A76_defconfig +BANANAPI M1 PLUS +M: Jagan Teki <[email protected]> +S: Maintained +F: configs/bananapi_m1_plus_defconfig + BANANAPI M2 ULTRA BOARD M: Chen-Yu Tsai <[email protected]> S: Maintained
configs/bananapi_m1_plus_defconfig new file +24 -0
@@ -0,0 +1,24 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_MACH_SUN7I=y +CONFIG_DRAM_CLK=432 +CONFIG_MACPWR="PH23" +CONFIG_VIDEO_COMPOSITE=y +CONFIG_GMAC_TX_DELAY=3 +CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-bananapi-m1-plus" +CONFIG_AHCI=y +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_SPL=y +CONFIG_SPL_I2C_SUPPORT=y +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_FPGA is not set +# CONFIG_SPL_DOS_PARTITION is not set +# CONFIG_SPL_ISO_PARTITION is not set +# CONFIG_SPL_EFI_PARTITION is not set +CONFIG_NETCONSOLE=y +CONFIG_ETH_DESIGNWARE=y +CONFIG_RGMII=y +CONFIG_SUN7I_GMAC=y +CONFIG_SCSI=y +CONFIG_USB_EHCI_HCD=y
Signature · 1 line
2.7.4