Patch "serial: 8250_early: Only set divisor if valid clk & baud" has been added to the 4.14-stable tree
Subsystems (2)
This is a note to let you know that I've just added the patch titled
serial: 8250_early: Only set divisor if valid clk & baud
to the 4.14-stable tree which can be found at:
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary
The filename of the patch is:
serial-8250_early-only-set-divisor-if-valid-clk-baud.patch
and it can be found in the queue-4.14 subdirectory.
If you, or anyone else, feels it should not be added to the stable tree, please let <[email protected]> know about it.
Quoted 1 line
From
0ff3ab701963a845d52337ded7eebf2d1a14fe00Mon Sep 17 00:00:00 2001
From: Matt Redfearn <[email protected]>
Date: Wed, 22 Nov 2017 09:57:28 +0000
Subject: serial: 8250_early: Only set divisor if valid clk & baud
From: Matt Redfearn <[email protected]>
commit 0ff3ab701963a845d52337ded7eebf2d1a14fe00 upstream.
If either uartclk or baud are 0, avoid calculating and setting a divisor based on them since the output will almost certainly be garbage.
This also allows platforms such as the MIPS generic kernel, which has no way to know a valid BASE_BASE for the board it is actually booted on at compile time, to set BASE_BAUD to 0 and avoid early_8250 setting a bad divisor.
This fixes a regression caused by commit 31cb9a8575ca ("earlycon:
initialise baud field of earlycon device structure"), which changed the behavior of of_setup_earlycon such that it sets a baud rate in the earlycon structure where previously it was left as 0. All boards supported by the MIPS generic kernel started outputting garbage from the boot console due to an incorrect divisor being set.
--- drivers/tty/serial/8250/8250_early.c | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-)
drivers/tty/serial/8250/8250_early.c +8 -6
@@ -125,12 +125,14 @@ static void __init init_port(struct earlserial8250_early_out (port,UART_FCR ,0 );/* no fifo */ serial8250_early_out (port,UART_MCR ,0x3 );/* DTR + RTS */ - divisor =DIV_ROUND_CLOSEST (port->uartclk,16 * device->baud); - c =serial8250_early_in (port,UART_LCR ); -serial8250_early_out (port,UART_LCR , c |UART_LCR_DLAB ); -serial8250_early_out (port,UART_DLL , divisor &0xff ); -serial8250_early_out (port,UART_DLM , (divisor >>8 ) &0xff ); -serial8250_early_out (port,UART_LCR , c & ~UART_LCR_DLAB ); +if (port->uartclk && device->baud) { + divisor =DIV_ROUND_CLOSEST (port->uartclk,16 * device->baud); + c =serial8250_early_in (port,UART_LCR ); +serial8250_early_out (port,UART_LCR , c |UART_LCR_DLAB ); +serial8250_early_out (port,UART_DLL , divisor &0xff ); +serial8250_early_out (port,UART_DLM , (divisor >>8 ) &0xff ); +serial8250_early_out (port,UART_LCR , c & ~UART_LCR_DLAB ); + } } int __init early_serial8250_setup(struct earlycon_device *device,
Patches currently in stable-queue which might be from [email protected] are
queue-4.14/mips-add-custom-serial.h-with-base_baud-override-for-generic-kernel.patch queue-4.14/serial-8250_early-only-set-divisor-if-valid-clk-baud.patch