microblaze: Moved U-boot headers to Kconfig
Subsystems (2)
cover microblaze: Moved U-boot headers to Kconfig
This seris of patch moved microblaze u-boot headers to the kconfig and enabled it in respective defconfig.
These are the configs:
-CONFIG_XILINX_GPIO
-CONFIG_XILINX_TB_WATCHDOG
Vipul Kumar (2):
microblaze: Added Kconfig support for CONFIG_XILINX_GPIO
microblaze: wdt: Added Kconfig support for CONFIG_XILINX_TB_WATCHDOG
configs/microblaze-generic_defconfig | 2 ++ drivers/gpio/Kconfig | 5 +++++ drivers/watchdog/Kconfig | 6 ++++++ include/configs/microblaze-generic.h | 2 -- 4 files changed, 13 insertions(+), 2 deletions(-)
--
2.7.4
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
PATCH 1/2 microblaze: Added Kconfig support for CONFIG_XILINX_GPIO
This patch added Kconfig support for CONFIG_XILINX_GPIO and enabled it in respective defconfig.
--- configs/microblaze-generic_defconfig | 1 + drivers/gpio/Kconfig | 5 +++++ include/configs/microblaze-generic.h | 1 - 3 files changed, 6 insertions(+), 1 deletion(-)
configs/microblaze-generic_defconfig +1 -0
@@ -42,6 +42,7 @@ CONFIG_SPL_OF_CONTROL=y CONFIG_OF_EMBED=y CONFIG_NETCONSOLE=y CONFIG_SPL_DM=y +CONFIG_XILINX_GPIO=y CONFIG_MTD_NOR_FLASH=y CONFIG_PHY_ATHEROS=y CONFIG_PHY_BROADCOM=y
drivers/gpio/Kconfig +5 -0
@@ -183,6 +183,11 @@ config SANDBOX_GPIO_COUNT of 'anonymous' GPIOs that do not belong to any device or bank. Select a suitable value depending on your needs. +config XILINX_GPIO + bool "Enable Xilinx GPIO driver" + help + This config enable the Xilinx GPIO driver for Microblaze. + config CMD_TCA642X bool "tca642x - Command to access tca642x state" help
include/configs/microblaze-generic.h +0 -1
@@ -41,7 +41,6 @@/* gpio */ #ifdef XILINX_GPIO_BASEADDR -# define CONFIG_XILINX_GPIO # define CONFIG_SYS_GPIO_0_ADDR XILINX_GPIO_BASEADDR#endif
--
2.7.4
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
PATCH 1/2 microblaze: Added Kconfig support for CONFIG_XILINX_GPIO
Quoted 28 lines · Vipul Kumar
This patch added
Kconfigsupport forCONFIG_XILINX_GPIOand enabled it in respective defconfig.Signed-off-by Vipul Kumar <[email protected]>Signed-off-by Siva Durga Prasad Paladugu <[email protected]>--- configs/microblaze-generic_defconfig | 1 + drivers/gpio/Kconfig | 5 +++++ include/configs/microblaze-generic.h | 1 - 3 files changed, 6 insertions(+), 1 deletion(-)configs/microblaze-generic_defconfig +1
-0@@ -42,6 +42,7 @@ CONFIG_SPL_OF_CONTROL=y CONFIG_OF_EMBED=y CONFIG_NETCONSOLE=y CONFIG_SPL_DM=y +CONFIG_XILINX_GPIO=y CONFIG_MTD_NOR_FLASH=y CONFIG_PHY_ATHEROS=y CONFIG_PHY_BROADCOM=ydrivers/gpio/Kconfig +0
-0
drivers/gpio/Kconfig config SANDBOX_GPIO_COUNT · line 187
Quoted 5 lines
drivers/gpio/Kconfig +2
-0@@ -183,6 +183,11 @@ config SANDBOX_GPIO_COUNT of 'anonymous' GPIOs that do not belong to any device or bank. Select a suitable value depending on your needs. +config XILINX_GPIO + bool "Enable Xilinx GPIO driver"
Remove "Enable" from description.
M
Quoted 19 lines
drivers/gpio/Kconfig +3
-0+ help + This config enable the Xilinx GPIO driver for Microblaze. + config CMD_TCA642X bool "tca642x - Command to access tca642x state" helpinclude/configs/microblaze-generic.h +0
-1@@ -41,7 +41,6 @@/* gpio */ #ifdef XILINX_GPIO_BASEADDR -# define CONFIG_XILINX_GPIO # define CONFIG_SYS_GPIO_0_ADDR XILINX_GPIO_BASEADDR#endif
PATCH 2/2 microblaze: wdt: Added Kconfig support for CONFIG_XILINX_TB_WATCHDOG
In reply to Vipul KumarThis patch added Kconfig support for CONFIG_XILINX_TB_WATCHDOG and enabled it in respective defconfig.
--- configs/microblaze-generic_defconfig | 1 + drivers/watchdog/Kconfig | 6 ++++++ include/configs/microblaze-generic.h | 1 - 3 files changed, 7 insertions(+), 1 deletion(-)
configs/microblaze-generic_defconfig +1 -0
@@ -59,3 +59,4 @@ CONFIG_XILINX_AXIEMAC=y CONFIG_XILINX_EMACLITE=y CONFIG_SYS_NS16550=y CONFIG_XILINX_UARTLITE=y +CONFIG_XILINX_TB_WATCHDOG=y
drivers/watchdog/Kconfig +6 -0
@@ -78,4 +78,10 @@ config WDT_ORION Select this to enable Orion watchdog timer, which can be found on some Marvell Armada chips. +config XILINX_TB_WATCHDOG + bool "Xilinx watchdog timer support" + depends on MICROBLAZE && !SPL_BUILD + help + Available for Xilinx Axi platforms to service timebase watchdog timer. + endmenu
include/configs/microblaze-generic.h +0 -1
@@ -50,7 +50,6 @@# define CONFIG_WATCHDOG_IRQ XILINX_WATCHDOG_IRQ# ifndef CONFIG_SPL_BUILD # define CONFIG_HW_WATCHDOG -# define CONFIG_XILINX_TB_WATCHDOG # endif #endif
--
2.7.4
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
PATCH 2/2 microblaze: wdt: Added Kconfig support for CONFIG_XILINX_TB_WATCHDOG
Quoted 25 lines · Vipul Kumar
This patch added
Kconfigsupport forCONFIG_XILINX_TB_WATCHDOGand enabled it in respective defconfig.Signed-off-by Vipul Kumar <[email protected]>Signed-off-by Siva Durga Prasad Paladugu <[email protected]>--- configs/microblaze-generic_defconfig | 1 + drivers/watchdog/Kconfig | 6 ++++++ include/configs/microblaze-generic.h | 1 - 3 files changed, 7 insertions(+), 1 deletion(-)configs/microblaze-generic_defconfig +1
-0@@ -59,3 +59,4 @@ CONFIG_XILINX_AXIEMAC=y CONFIG_XILINX_EMACLITE=y CONFIG_SYS_NS16550=y CONFIG_XILINX_UARTLITE=y +CONFIG_XILINX_TB_WATCHDOG=ydrivers/watchdog/Kconfig +0
-0
drivers/watchdog/Kconfig config WDT_ORION · line 83
Quoted 6 lines
drivers/watchdog/Kconfig +3
-0@@ -78,4 +78,10 @@ config WDT_ORION Select this to enable Orion watchdog timer, which can be found on some Marvell Armada chips. +config XILINX_TB_WATCHDOG + bool "Xilinx watchdog timer support" + depends on MICROBLAZE && !SPL_BUILD
You should also add there select HW_WATCHDOG.
Thanks,
Michal
Quoted 17 lines
drivers/watchdog/Kconfig +3
-0+ help + Available for Xilinx Axi platforms to service timebase watchdog timer. + endmenuinclude/configs/microblaze-generic.h +0
-1@@ -50,7 +50,6 @@# define CONFIG_WATCHDOG_IRQ XILINX_WATCHDOG_IRQ# ifndef CONFIG_SPL_BUILD # define CONFIG_HW_WATCHDOG -# define CONFIG_XILINX_TB_WATCHDOG # endif #endif