Skip to contentSkip to conversation

x86/CPU: Use correct macros for Cyrix calls on Geode processors

PATCH In review Matthew Whitehead 2 participants 2 messages Mar 6, 2019 x86

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 x86/CPU: Use correct macros for Cyrix calls on Geode processors

There are comments in processor-cyrix.h advising you to _not_ make calls using the deprecated macros in this style:

  setCx86_old(CX86_CCR4, getCx86_old(CX86_CCR4) | 0x80);

This is because it expands the macro into a non-functioning calling sequence. The calling order must be:

  outb(CX86_CCR2, 0x22);
  inb(0x23);

From the comments:

* When using the old macros a line like
* setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
* gets expanded to:
* do {
* outb((CX86_CCR2), 0x22);
* outb((({
* outb((CX86_CCR2), 0x22);
* inb(0x23);
* }) | 0x88), 0x23);
* } while (0);

The new macros fix this problem, so use them instead. Tested on an actual Geode processor.

---
 arch/x86/kernel/cpu/cyrix.c | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)
arch/x86/kernel/cpu/cyrix.c +7 -7
index d12226f..1d9b8aa 100644
@@ -124,7 +124,7 @@ static void set_cx86_reorder(void)
 	setCx86(CX86_CCR3, (ccr3 & 0x0f) | 0x10); /* enable MAPEN */
 
 	/* Load/Store Serialize to mem access disable (=reorder it) */
-	setCx86_old(CX86_PCR0, getCx86_old(CX86_PCR0) & ~0x80);
+	setCx86(CX86_PCR0, getCx86(CX86_PCR0) & ~0x80);
 	/* set load/store serialize from 1GB to 4GB */
 	ccr3 |= 0xe0;
 	setCx86(CX86_CCR3, ccr3);
@@ -135,11 +135,11 @@ static void set_cx86_memwb(void)
 	pr_info("Enable Memory-Write-back mode on Cyrix/NSC processor.\n");
 
 	/* CCR2 bit 2: unlock NW bit */
-	setCx86_old(CX86_CCR2, getCx86_old(CX86_CCR2) & ~0x04);
+	setCx86(CX86_CCR2, getCx86(CX86_CCR2) & ~0x04);
 	/* set 'Not Write-through' */
 	write_cr0(read_cr0() | X86_CR0_NW);
 	/* CCR2 bit 2: lock NW bit and set WT1 */
-	setCx86_old(CX86_CCR2, getCx86_old(CX86_CCR2) | 0x14);
+	setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x14);
 }
 
 /*
@@ -153,14 +153,14 @@ static void geode_configure(void)
 	local_irq_save(flags);
 
 	/* Suspend on halt power saving and enable #SUSP pin */
-	setCx86_old(CX86_CCR2, getCx86_old(CX86_CCR2) | 0x88);
+	setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
 
 	ccr3 = getCx86(CX86_CCR3);
 	setCx86(CX86_CCR3, (ccr3 & 0x0f) | 0x10);	/* enable MAPEN */
 
 
 	/* FPU fast, DTE cache, Mem bypass */
-	setCx86_old(CX86_CCR4, getCx86_old(CX86_CCR4) | 0x38);
+	setCx86(CX86_CCR4, getCx86(CX86_CCR4) | 0x38);
 	setCx86(CX86_CCR3, ccr3);			/* disable MAPEN */
 
 	set_cx86_memwb();
@@ -296,7 +296,7 @@ static void init_cyrix(struct cpuinfo_x86 *c)
 		/* GXm supports extended cpuid levels 'ala' AMD */
 		if (c->cpuid_level == 2) {
 			/* Enable cxMMX extensions (GX1 Datasheet 54) */
-			setCx86_old(CX86_CCR7, getCx86_old(CX86_CCR7) | 1);
+			setCx86(CX86_CCR7, getCx86(CX86_CCR7) | 1);
 
 			/*
 			 * GXm : 0x30 ... 0x5f GXm  datasheet 51
@@ -319,7 +319,7 @@ static void init_cyrix(struct cpuinfo_x86 *c)
 		if (dir1 > 7) {
 			dir0_msn++;  /* M II */
 			/* Enable MMX extensions (App note 108) */
-			setCx86_old(CX86_CCR7, getCx86_old(CX86_CCR7)|1);
+			setCx86(CX86_CCR7, getCx86(CX86_CCR7)|1);
 		} else {
 			/* A 6x86MX - it has the bug. */
 			set_cpu_bug(c, X86_BUG_COMA);
Signature · 1 line
1.8.3.1
#1 lore raw

Matthew,

Quoted 24 lines · Matthew Whitehead

There are comments in processor-cyrix.h advising you to _not_ make calls using the deprecated macros in this style:

  setCx86_old(CX86_CCR4, getCx86_old(CX86_CCR4) | 0x80);

This is because it expands the macro into a non-functioning calling sequence. The calling order must be:

  outb(CX86_CCR2, 0x22);
  inb(0x23);
Quoted 1 line

From the comments:

* When using the old macros a line like
* setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
* gets expanded to:
* do {
* outb((CX86_CCR2), 0x22);
* outb((({
* outb((CX86_CCR2), 0x22);
* inb(0x23);
* }) | 0x88), 0x23);
* } while (0);

Quoted 2 lines

The new macros fix this problem, so use them instead. Tested on an actual Geode processor.

Thanks for cleaning that up, but now the old macros are unused, so please remove them entirely including the comment.

Thanks,

tglx