Skip to contentSkip to conversation

EDAC, altera: Less Intrusive Error Injection

PATCH In review [email protected] 2 participants 3 messages Mar 26, 2019 – Mar 29, 2019

Subsystems (2)
EDAC-core Arm/socfpga EDAC support
lore
Share & tools
lore

[email protected]

author
#0 lore raw

PATCH 1/2 EDAC, altera: Less Intrusive Error Injection

From: Thor Thayer <[email protected]>

Improve the Arria10 and Stratix10 error injection routine by reading the data and changing just 1 bit before writing back out. Previous routine would overwrite the first bytes to 0 then change 1 bit but this method is less intrusive.

Signed-off-by Thor Thayer <[email protected]>
---
 drivers/edac/altera_edac.c | 30 +++++++++++++-----------------
 drivers/edac/altera_edac.h |  2 +-
 2 files changed, 14 insertions(+), 18 deletions(-)
drivers/edac/altera_edac.c +13 -17
index 5ff263850cc7..acb3006df631 100644
@@ -1762,28 +1762,24 @@ static ssize_t altr_edac_a10_device_trig2(struct file *file,
 	if (trig_type == ALTR_UE_TRIGGER_CHAR) {
 		writel(priv->ue_set_mask, set_addr);
 	} else {
-		/* Setup write of 0 to first 4 bytes */
-		writel(0x0, drvdata->base + ECC_BLK_WDATA0_OFST);
-		writel(0x0, drvdata->base + ECC_BLK_WDATA1_OFST);
-		writel(0x0, drvdata->base + ECC_BLK_WDATA2_OFST);
-		writel(0x0, drvdata->base + ECC_BLK_WDATA3_OFST);
-		/* Setup write of 4 bytes */
+		/* Setup read/write of 4 bytes */
 		writel(ECC_WORD_WRITE, drvdata->base + ECC_BLK_DBYTECTRL_OFST);
 		/* Setup Address to 0 */
-		writel(0x0, drvdata->base + ECC_BLK_ADDRESS_OFST);
-		/* Setup accctrl to write & data override */
-		writel(ECC_WRITE_DOVR, drvdata->base + ECC_BLK_ACCCTRL_OFST);
-		/* Kick it. */
-		writel(ECC_XACT_KICK, drvdata->base + ECC_BLK_STARTACC_OFST);
-		/* Setup accctrl to read & ecc override */
-		writel(ECC_READ_EOVR, drvdata->base + ECC_BLK_ACCCTRL_OFST);
+		writel(0, drvdata->base + ECC_BLK_ADDRESS_OFST);
+		/* Setup accctrl to read & ecc & data override */
+		writel(ECC_READ_EDOVR, drvdata->base + ECC_BLK_ACCCTRL_OFST);
 		/* Kick it. */
 		writel(ECC_XACT_KICK, drvdata->base + ECC_BLK_STARTACC_OFST);
 		/* Setup write for single bit change */
-		writel(0x1, drvdata->base + ECC_BLK_WDATA0_OFST);
-		writel(0x0, drvdata->base + ECC_BLK_WDATA1_OFST);
-		writel(0x0, drvdata->base + ECC_BLK_WDATA2_OFST);
-		writel(0x0, drvdata->base + ECC_BLK_WDATA3_OFST);
+		writel(readl(drvdata->base + ECC_BLK_RDATA0_OFST) ^ 0x1,
+		       drvdata->base + ECC_BLK_WDATA0_OFST);
+		writel(readl(drvdata->base + ECC_BLK_RDATA1_OFST),
+		       drvdata->base + ECC_BLK_WDATA1_OFST);
+		writel(readl(drvdata->base + ECC_BLK_RDATA2_OFST),
+		       drvdata->base + ECC_BLK_WDATA2_OFST);
+		writel(readl(drvdata->base + ECC_BLK_RDATA3_OFST),
+		       drvdata->base + ECC_BLK_WDATA3_OFST);
+
 		/* Copy Read ECC to Write ECC */
 		writel(readl(drvdata->base + ECC_BLK_RECC0_OFST),
 		       drvdata->base + ECC_BLK_WECC0_OFST);
drivers/edac/altera_edac.h +1 -1
index 60513f201ffb..1532ec9c3510 100644
@@ -321,7 +321,7 @@ struct altr_sdram_mc_data {
 #define ECC_BLK_STARTACC_OFST             0x7C
 
 #define ECC_XACT_KICK                     0x10000
-#define ECC_WORD_WRITE                    0xF
+#define ECC_WORD_WRITE                    0xFF
 #define ECC_WRITE_DOVR                    0x101
 #define ECC_WRITE_EDOVR                   0x103
 #define ECC_READ_EOVR                     0x2
Signature · 1 line
2.7.4
author
#1 lore raw

PATCH 2/2 EDAC, altera: Initialize peripheral FIFOs in probe()

From: Thor Thayer <[email protected]>

The FIFO memory and ECC initialization doesn't need to be done as a separate operation early in the startup.

Improve the Arria10 and Stratix10 peripheral FIFO init by initializing memory and enabling ECC as part of the device driver initialization.

Signed-off-by Thor Thayer <[email protected]>
---
 drivers/edac/altera_edac.c | 162 +++++++++++++++++++++++++--------------------
 1 file changed, 91 insertions(+), 71 deletions(-)
drivers/edac/altera_edac.c +91 -71
index acb3006df631..761199175c76 100644
@@ -1361,8 +1361,19 @@ static const struct edac_device_prv_data a10_l2ecc_data = {
 
 #ifdef CONFIG_EDAC_ALTERA_ETHERNET
 
+static int __init socfpga_init_ethernet_ecc(struct altr_edac_device_dev *dev)
+{
+	int ret;
+
+	ret = altr_init_a10_ecc_device_type("altr,socfpga-eth-mac-ecc");
+	if (ret)
+		return ret;
+
+	return altr_check_ecc_deps(dev);
+}
+
 static const struct edac_device_prv_data a10_enetecc_data = {
-	.setup = altr_check_ecc_deps,
+	.setup = socfpga_init_ethernet_ecc,
 	.ce_clear_mask = ALTR_A10_ECC_SERRPENA,
 	.ue_clear_mask = ALTR_A10_ECC_DERRPENA,
 	.ecc_enable_mask = ALTR_A10_COMMON_ECC_EN_CTL,

@@ -1374,21 +1385,25 @@ static const struct edac_device_prv_data a10_enetecc_data = {
 	.inject_fops = &altr_edac_a10_device_inject2_fops,
 };
 
-static int __init socfpga_init_ethernet_ecc(void)
-{
-	return altr_init_a10_ecc_device_type("altr,socfpga-eth-mac-ecc");
-}
-
-early_initcall(socfpga_init_ethernet_ecc);
-
 #endif	/* CONFIG_EDAC_ALTERA_ETHERNET */
 
 /********************** NAND Device Functions **********************/
 
 #ifdef CONFIG_EDAC_ALTERA_NAND
 
+static int __init socfpga_init_nand_ecc(struct altr_edac_device_dev *device)
+{
+	int ret;
+
+	ret = altr_init_a10_ecc_device_type("altr,socfpga-nand-ecc");
+	if (ret)
+		return ret;
+
+	return altr_check_ecc_deps(device);
+}
+
 static const struct edac_device_prv_data a10_nandecc_data = {
-	.setup = altr_check_ecc_deps,
+	.setup = socfpga_init_nand_ecc,
 	.ce_clear_mask = ALTR_A10_ECC_SERRPENA,
 	.ue_clear_mask = ALTR_A10_ECC_DERRPENA,
 	.ecc_enable_mask = ALTR_A10_COMMON_ECC_EN_CTL,

@@ -1400,21 +1415,25 @@ static const struct edac_device_prv_data a10_nandecc_data = {
 	.inject_fops = &altr_edac_a10_device_inject_fops,
 };
 
-static int __init socfpga_init_nand_ecc(void)
-{
-	return altr_init_a10_ecc_device_type("altr,socfpga-nand-ecc");
-}
-
-early_initcall(socfpga_init_nand_ecc);
-
 #endif	/* CONFIG_EDAC_ALTERA_NAND */
 
 /********************** DMA Device Functions **********************/
 
 #ifdef CONFIG_EDAC_ALTERA_DMA
 
+static int __init socfpga_init_dma_ecc(struct altr_edac_device_dev *device)
+{
+	int ret;
+
+	ret = altr_init_a10_ecc_device_type("altr,socfpga-dma-ecc");
+	if (ret)
+		return ret;
+
+	return altr_check_ecc_deps(device);
+}
+
 static const struct edac_device_prv_data a10_dmaecc_data = {
-	.setup = altr_check_ecc_deps,
+	.setup = socfpga_init_dma_ecc,
 	.ce_clear_mask = ALTR_A10_ECC_SERRPENA,
 	.ue_clear_mask = ALTR_A10_ECC_DERRPENA,
 	.ecc_enable_mask = ALTR_A10_COMMON_ECC_EN_CTL,

@@ -1426,21 +1445,25 @@ static const struct edac_device_prv_data a10_dmaecc_data = {
 	.inject_fops = &altr_edac_a10_device_inject_fops,
 };
 
-static int __init socfpga_init_dma_ecc(void)
-{
-	return altr_init_a10_ecc_device_type("altr,socfpga-dma-ecc");
-}
-
-early_initcall(socfpga_init_dma_ecc);
-
 #endif	/* CONFIG_EDAC_ALTERA_DMA */
 
 /********************** USB Device Functions **********************/
 
 #ifdef CONFIG_EDAC_ALTERA_USB
 
+static int __init socfpga_init_usb_ecc(struct altr_edac_device_dev *device)
+{
+	int ret;
+
+	ret = altr_init_a10_ecc_device_type("altr,socfpga-usb-ecc");
+	if (ret)
+		return ret;
+
+	return altr_check_ecc_deps(device);
+}
+
 static const struct edac_device_prv_data a10_usbecc_data = {
-	.setup = altr_check_ecc_deps,
+	.setup = socfpga_init_usb_ecc,
 	.ce_clear_mask = ALTR_A10_ECC_SERRPENA,
 	.ue_clear_mask = ALTR_A10_ECC_DERRPENA,
 	.ecc_enable_mask = ALTR_A10_COMMON_ECC_EN_CTL,

@@ -1452,21 +1475,25 @@ static const struct edac_device_prv_data a10_usbecc_data = {
 	.inject_fops = &altr_edac_a10_device_inject2_fops,
 };
 
-static int __init socfpga_init_usb_ecc(void)
-{
-	return altr_init_a10_ecc_device_type("altr,socfpga-usb-ecc");
-}
-
-early_initcall(socfpga_init_usb_ecc);
-
 #endif	/* CONFIG_EDAC_ALTERA_USB */
 
 /********************** QSPI Device Functions **********************/
 
 #ifdef CONFIG_EDAC_ALTERA_QSPI
 
+static int __init socfpga_init_qspi_ecc(struct altr_edac_device_dev *device)
+{
+	int ret;
+
+	ret = altr_init_a10_ecc_device_type("altr,socfpga-qspi-ecc");
+	if (ret)
+		return ret;
+
+	return altr_check_ecc_deps(device);
+}
+
 static const struct edac_device_prv_data a10_qspiecc_data = {
-	.setup = altr_check_ecc_deps,
+	.setup = socfpga_init_qspi_ecc,
 	.ce_clear_mask = ALTR_A10_ECC_SERRPENA,
 	.ue_clear_mask = ALTR_A10_ECC_DERRPENA,
 	.ecc_enable_mask = ALTR_A10_COMMON_ECC_EN_CTL,

@@ -1478,13 +1505,6 @@ static const struct edac_device_prv_data a10_qspiecc_data = {
 	.inject_fops = &altr_edac_a10_device_inject_fops,
 };
 
-static int __init socfpga_init_qspi_ecc(void)
-{
-	return altr_init_a10_ecc_device_type("altr,socfpga-qspi-ecc");
-}
-
-early_initcall(socfpga_init_qspi_ecc);
-
 #endif	/* CONFIG_EDAC_ALTERA_QSPI */
 
 /********************* SDMMC Device Functions **********************/

@@ -1593,6 +1613,35 @@ static int altr_portb_setup(struct altr_edac_device_dev *device)
 	return rc;
 }
 
+static int __init socfpga_init_sdmmc_ecc(struct altr_edac_device_dev *device)
+{
+	int rc = -ENODEV;
+	struct device_node *child;
+
+	child = of_find_compatible_node(NULL, NULL, "altr,socfpga-sdmmc-ecc");
+	if (!child)
+		return -ENODEV;
+
+	if (!of_device_is_available(child))
+		goto exit;
+
+	if (validate_parent_available(child))
+		goto exit;
+
+	/* Init portB */
+	rc = altr_init_a10_ecc_block(child, ALTR_A10_SDMMC_IRQ_MASK,
+				     a10_sdmmceccb_data.ecc_enable_mask, 1);
+	if (rc)
+		goto exit;
+
+	/* Setup portB */
+	return altr_portb_setup(device);
+
+exit:
+	of_node_put(child);
+	return rc;
+}
+
 static irqreturn_t altr_edac_a10_ecc_irq_portb(int irq, void *dev_id)
 {
 	struct altr_edac_device_dev *ad = dev_id;

@@ -1617,7 +1666,7 @@ static irqreturn_t altr_edac_a10_ecc_irq_portb(int irq, void *dev_id)
 }
 
 static const struct edac_device_prv_data a10_sdmmcecca_data = {
-	.setup = altr_portb_setup,
+	.setup = socfpga_init_sdmmc_ecc,
 	.ce_clear_mask = ALTR_A10_ECC_SERRPENA,
 	.ue_clear_mask = ALTR_A10_ECC_DERRPENA,
 	.ecc_enable_mask = ALTR_A10_COMMON_ECC_EN_CTL,

@@ -1630,7 +1679,7 @@ static const struct edac_device_prv_data a10_sdmmcecca_data = {
 };
 
 static const struct edac_device_prv_data a10_sdmmceccb_data = {
-	.setup = altr_portb_setup,
+	.setup = socfpga_init_sdmmc_ecc,
 	.ce_clear_mask = ALTR_A10_ECC_SERRPENB,
 	.ue_clear_mask = ALTR_A10_ECC_DERRPENB,
 	.ecc_enable_mask = ALTR_A10_COMMON_ECC_EN_CTL,

@@ -1642,35 +1691,6 @@ static const struct edac_device_prv_data a10_sdmmceccb_data = {
 	.inject_fops = &altr_edac_a10_device_inject_fops,
 };
 
-static int __init socfpga_init_sdmmc_ecc(void)
-{
-	int rc = -ENODEV;
-	struct device_node *child;
-
-	if (!socfpga_is_a10() && !socfpga_is_s10())
-		return -ENODEV;
-
-	child = of_find_compatible_node(NULL, NULL, "altr,socfpga-sdmmc-ecc");
-	if (!child) {
-		edac_printk(KERN_WARNING, EDAC_DEVICE, "SDMMC node not found\n");
-		return -ENODEV;
-	}
-
-	if (!of_device_is_available(child))
-		goto exit;
-
-	if (validate_parent_available(child))
-		goto exit;
-
-	rc = altr_init_a10_ecc_block(child, ALTR_A10_SDMMC_IRQ_MASK,
-				     a10_sdmmcecca_data.ecc_enable_mask, 1);
-exit:
-	of_node_put(child);
-	return rc;
-}
-
-early_initcall(socfpga_init_sdmmc_ecc);
-
 #endif	/* CONFIG_EDAC_ALTERA_SDMMC */
 
 /********************* Arria10 EDAC Device Functions *************************/
Signature · 1 line
2.7.4
maintainer
#2 lore raw

Re: [PATCH 2/2] EDAC, altera: Initialize peripheral FIFOs in probe()

Quoted 5 lines · On Tue, Mar 26, 2019 at 04:29:31PM -0500, [email protected] wrote:

From: Thor Thayer <[email protected]>

The FIFO memory and ECC initialization doesn't need to be done as a separate operation early in the startup.

Quoted 8 lines

Improve the Arria10 and Stratix10 peripheral FIFO init by initializing memory and enabling ECC as part of the device driver initialization.

Signed-off-by Thor Thayer <[email protected]>
---
 drivers/edac/altera_edac.c | 162 +++++++++++++++++++++++++--------------------
 1 file changed, 91 insertions(+), 71 deletions(-)

Both applied,
thanks.