Skip to contentSkip to conversation

drm/komeda: Add SMMU support on Komeda driver

PATCH Superseded Lowry Li (Arm Technology China) 3 participants 9 messages Apr 30, 2019 – Jun 6, 2019

Subsystems (5)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

cover drm/komeda: Add SMMU support on Komeda driver

Hi,

This serie aims at adding the support for SMMU on Komeda driver. Also updates the device-tree doc about how to enable SMMU by devicetree.

This patch series depends on:
- https://patchwork.freedesktop.org/series/58710/
- https://patchwork.freedesktop.org/series/59000/
- https://patchwork.freedesktop.org/series/59002/

Thanks,
Lowry

Lowry Li (Arm Technology China) (2):
drm/komeda: Adds SMMU support
dt/bindings: drm/komeda: Adds SMMU support for D71 devicetree

 .../devicetree/bindings/display/arm,komeda.txt     |  7 ++++
 .../gpu/drm/arm/display/komeda/d71/d71_component.c |  5 +++
 drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c   | 49 ++++++++++++++++++++++
 drivers/gpu/drm/arm/display/komeda/komeda_dev.c    | 17 ++++++++
 drivers/gpu/drm/arm/display/komeda/komeda_dev.h    |  7 ++++
 .../drm/arm/display/komeda/komeda_framebuffer.c    |  2 +
 .../drm/arm/display/komeda/komeda_framebuffer.h    |  2 +
 7 files changed, 89 insertions(+)
Signature · 1 line
1.9.1
#1 lore raw

PATCH 1/2 drm/komeda: Adds SMMU support

Adds iommu_connect and disconnect for SMMU support, and configures TBU translation once SMMU has been attached to the display device.

---
 .../gpu/drm/arm/display/komeda/d71/d71_component.c |  5 +++
 drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c   | 49 ++++++++++++++++++++++
 drivers/gpu/drm/arm/display/komeda/komeda_dev.c    | 17 ++++++++
 drivers/gpu/drm/arm/display/komeda/komeda_dev.h    |  7 ++++
 .../drm/arm/display/komeda/komeda_framebuffer.c    |  2 +
 .../drm/arm/display/komeda/komeda_framebuffer.h    |  2 +
 6 files changed, 82 insertions(+)
drivers/gpu/drm/arm/display/komeda/d71/d71_component.c +5 -0
index 33ca171..9065040 100644
@@ -215,6 +215,8 @@ static void d71_layer_update(struct komeda_component *c,
 	malidp_write32(reg, LAYER_FMT, kfb->format_caps->hw_id);
 	malidp_write32(reg, BLK_IN_SIZE, HV_SIZE(st->hsize, st->vsize));
 
+	if (kfb->is_va)
+		ctrl |= L_TBU_EN;
 	malidp_write32_mask(reg, BLK_CONTROL, ctrl_mask, ctrl);
 }
 
@@ -348,6 +350,9 @@ static void d71_wb_layer_update(struct komeda_component *c,
 			       fb->pitches[i] & 0xFFFF);
 	}
 
+	if (kfb->is_va)
+		ctrl |= LW_TBU_EN;
+
 	malidp_write32(reg, LAYER_FMT, kfb->format_caps->hw_id);
 	malidp_write32(reg, BLK_IN_SIZE, HV_SIZE(st->hsize, st->vsize));
 	malidp_write32(reg, BLK_INPUT_ID0, to_d71_input_id(&state->inputs[0]));
drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c +49 -0

61 lines not on this page · raw message

drivers/gpu/drm/arm/display/komeda/komeda_dev.c +17 -0
index e4e5b58..2d97c82 100644
@@ -251,6 +251,18 @@ struct komeda_dev *komeda_dev_create(struct device *dev)
 	dev->dma_parms = &mdev->dma_parms;
 	dma_set_max_seg_size(dev, DMA_BIT_MASK(32));
 
+	mdev->iommu = iommu_get_domain_for_dev(mdev->dev);
+	if (!mdev->iommu)
+		DRM_INFO("continue without IOMMU support!\n");
+
+	if (mdev->iommu && mdev->funcs->connect_iommu) {
+		err = mdev->funcs->connect_iommu(mdev);
+		if (err) {
+			DRM_ERROR("connect iommu failed.\n");
+			goto err_cleanup;
+		}
+	}
+
 	err = sysfs_create_group(&dev->kobj, &komeda_sysfs_attr_group);
 	if (err) {
 		DRM_ERROR("create sysfs group failed.\n");
@@ -280,6 +292,11 @@ void komeda_dev_destroy(struct komeda_dev *mdev)
 	debugfs_remove_recursive(mdev->debugfs_root);
 #endif
 
+	if (mdev->iommu && mdev->funcs->disconnect_iommu)
+		if (mdev->funcs->disconnect_iommu(mdev))
+			DRM_ERROR("disconnect iommu failed.\n");
+	mdev->iommu = NULL;
+
 	for (i = 0; i < mdev->n_pipelines; i++) {
 		komeda_pipeline_destroy(mdev, mdev->pipelines[i]);
 		mdev->pipelines[i] = NULL;
drivers/gpu/drm/arm/display/komeda/komeda_dev.h +7 -0
index 83ace71..dac1eda 100644
@@ -92,6 +92,10 @@ struct komeda_dev_funcs {
 	int (*enum_resources)(struct komeda_dev *mdev);
 	/** @cleanup: call to chip to cleanup komeda_dev->chip data */
 	void (*cleanup)(struct komeda_dev *mdev);
+	/** @connect_iommu: Optional, connect to external iommu */
+	int (*connect_iommu)(struct komeda_dev *mdev);
+	/** @disconnect_iommu: Optional, disconnect to external iommu */
+	int (*disconnect_iommu)(struct komeda_dev *mdev);
 	/**
 	 * @irq_handler:
 	 *
@@ -184,6 +188,9 @@ struct komeda_dev {
 	 */
 	void *chip_data;
 
+	/** @iommu: iommu domain */
+	struct iommu_domain *iommu;
+
 	/** @debugfs_root: root directory of komeda debugfs */
 	struct dentry *debugfs_root;
 };
drivers/gpu/drm/arm/display/komeda/komeda_framebuffer.c +2 -0
index d5822a3..360ab70 100644
@@ -201,6 +201,8 @@ struct drm_framebuffer *
 		goto err_cleanup;
 	}
 
+	kfb->is_va = mdev->iommu ? true : false;
+
 	return &kfb->base;
 
 err_cleanup:
drivers/gpu/drm/arm/display/komeda/komeda_framebuffer.h +2 -0
index 6cbb2f6..f4046e2 100644
@@ -21,6 +21,8 @@ struct komeda_fb {
 	 * extends drm_format_info for komeda specific information
 	 */
 	const struct komeda_format_caps *format_caps;
+	/** @is_va: if smmu is enabled, it will be true */
+	bool is_va;
 	/** @aligned_w: aligned frame buffer width */
 	u32 aligned_w;
 	/** @aligned_h: aligned frame buffer height */
Signature · 6 lines
1.9.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#2 lore raw

Re: [v1,1/2] drm/komeda: Adds SMMU support

Quoted 184 lines · Lowry Li (Arm Technology China)

Adds iommu_connect and disconnect for SMMU support, and configures TBU translation once SMMU has been attached to the display device.

---
 .../gpu/drm/arm/display/komeda/d71/d71_component.c |  5 +++
 drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c   | 49 ++++++++++++++++++++++
 drivers/gpu/drm/arm/display/komeda/komeda_dev.c    | 17 ++++++++
 drivers/gpu/drm/arm/display/komeda/komeda_dev.h    |  7 ++++
 .../drm/arm/display/komeda/komeda_framebuffer.c    |  2 +
 .../drm/arm/display/komeda/komeda_framebuffer.h    |  2 +
 6 files changed, 82 insertions(+)
Signature · 1 line
1.9.1
drivers/gpu/drm/arm/display/komeda/d71/d71_component.c +5 -0
index 33ca171..9065040 100644
@@ -215,6 +215,8 @@ static void d71_layer_update(struct komeda_component *c,
 	malidp_write32(reg, LAYER_FMT, kfb->format_caps->hw_id);
 	malidp_write32(reg, BLK_IN_SIZE, HV_SIZE(st->hsize, st->vsize));
 
+	if (kfb->is_va)
+		ctrl |= L_TBU_EN;
 	malidp_write32_mask(reg, BLK_CONTROL, ctrl_mask, ctrl);
 }
 
@@ -348,6 +350,9 @@ static void d71_wb_layer_update(struct komeda_component *c,
 			       fb->pitches[i] & 0xFFFF);
 	}
 
+	if (kfb->is_va)
+		ctrl |= LW_TBU_EN;
+
 	malidp_write32(reg, LAYER_FMT, kfb->format_caps->hw_id);
 	malidp_write32(reg, BLK_IN_SIZE, HV_SIZE(st->hsize, st->vsize));
 	malidp_write32(reg, BLK_INPUT_ID0, to_d71_input_id(&state->inputs[0]));
drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c +49 -0
index 9603de9..45c98a7 100644
@@ -517,6 +517,53 @@ static void d71_init_fmt_tbl(struct komeda_dev *mdev)
 	table->n_formats = ARRAY_SIZE(d71_format_caps_table);
 }
 
+static int d71_connect_iommu(struct komeda_dev *mdev)
+{
+	struct d71_dev *d71 = mdev->chip_data;
+	u32 __iomem *reg = d71->gcu_addr;
+	u32 check_bits = (d71->num_pipelines == 2) ?
+			 GCU_STATUS_TCS0 | GCU_STATUS_TCS1 : GCU_STATUS_TCS0;
+	int i, ret;
+
+	if (!d71->integrates_tbu)
+		return -1;
+
+	malidp_write32_mask(reg, BLK_CONTROL, 0x7, TBU_CONNECT_MODE);
+
+	ret = dp_wait_cond(has_bits(check_bits, malidp_read32(reg, BLK_STATUS)),
+			100, 1000, 1000);
+	if (ret <= 0) {
+		DRM_ERROR("connect to TCU timeout!\n");
+		malidp_write32_mask(reg, BLK_CONTROL, 0x7, INACTIVE_MODE);
+		return -ETIMEDOUT;
+	}
+
+	for (i = 0; i < d71->num_pipelines; i++)
+		malidp_write32_mask(d71->pipes[i]->lpu_addr, LPU_TBU_CONTROL,
+				    LPU_TBU_CTRL_TLBPEN, LPU_TBU_CTRL_TLBPEN);
+	return 0;
+}
+
+static int d71_disconnect_iommu(struct komeda_dev *mdev)
+{
+	struct d71_dev *d71 = mdev->chip_data;
+	u32 __iomem *reg = d71->gcu_addr;
+	u32 check_bits = (d71->num_pipelines == 2) ?
+			 GCU_STATUS_TCS0 | GCU_STATUS_TCS1 : GCU_STATUS_TCS0;
+	int ret;
+
+	malidp_write32_mask(reg, BLK_CONTROL, 0x7, TBU_DISCONNECT_MODE);
+
+	ret = dp_wait_cond(((malidp_read32(reg, BLK_STATUS) & check_bits) == 0),
+			100, 1000, 1000);
+	if (ret <= 0) {
+		DRM_ERROR("disconnect from TCU timeout!\n");
+		malidp_write32_mask(reg, BLK_CONTROL, 0x7, INACTIVE_MODE);
+	}
+
+	return ret > 0 ? 0 : -1;
+}
+
 static struct komeda_dev_funcs d71_chip_funcs = {
 	.init_format_table = d71_init_fmt_tbl,
 	.enum_resources	= d71_enum_resources,
@@ -527,6 +574,8 @@ static void d71_init_fmt_tbl(struct komeda_dev *mdev)
 	.on_off_vblank	= d71_on_off_vblank,
 	.change_opmode	= d71_change_opmode,
 	.flush		= d71_flush,
+	.connect_iommu	= d71_connect_iommu,
+	.disconnect_iommu = d71_disconnect_iommu,
 };
 
 struct komeda_dev_funcs *
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +17 -0
index e4e5b58..2d97c82 100644
@@ -251,6 +251,18 @@ struct komeda_dev *komeda_dev_create(struct device *dev)
 	dev->dma_parms = &mdev->dma_parms;
 	dma_set_max_seg_size(dev, DMA_BIT_MASK(32));
 
+	mdev->iommu = iommu_get_domain_for_dev(mdev->dev);
+	if (!mdev->iommu)
+		DRM_INFO("continue without IOMMU support!\n");
+
+	if (mdev->iommu && mdev->funcs->connect_iommu) {
+		err = mdev->funcs->connect_iommu(mdev);
+		if (err) {
+			DRM_ERROR("connect iommu failed.\n");
+			goto err_cleanup;
+		}
+	}
+
 	err = sysfs_create_group(&dev->kobj, &komeda_sysfs_attr_group);
 	if (err) {
 		DRM_ERROR("create sysfs group failed.\n");
@@ -280,6 +292,11 @@ void komeda_dev_destroy(struct komeda_dev *mdev)
 	debugfs_remove_recursive(mdev->debugfs_root);
 #endif
 
+	if (mdev->iommu && mdev->funcs->disconnect_iommu)
+		if (mdev->funcs->disconnect_iommu(mdev))
+			DRM_ERROR("disconnect iommu failed.\n");
+	mdev->iommu = NULL;
+
 	for (i = 0; i < mdev->n_pipelines; i++) {
 		komeda_pipeline_destroy(mdev, mdev->pipelines[i]);
 		mdev->pipelines[i] = NULL;
drivers/gpu/drm/arm/display/komeda/komeda_dev.h +7 -0
index 83ace71..dac1eda 100644
@@ -92,6 +92,10 @@ struct komeda_dev_funcs {
 	int (*enum_resources)(struct komeda_dev *mdev);
 	/** @cleanup: call to chip to cleanup komeda_dev->chip data */
 	void (*cleanup)(struct komeda_dev *mdev);
+	/** @connect_iommu: Optional, connect to external iommu */
+	int (*connect_iommu)(struct komeda_dev *mdev);
+	/** @disconnect_iommu: Optional, disconnect to external iommu */
+	int (*disconnect_iommu)(struct komeda_dev *mdev);
 	/**
 	 * @irq_handler:
 	 *
@@ -184,6 +188,9 @@ struct komeda_dev {
 	 */
 	void *chip_data;
 
+	/** @iommu: iommu domain */
+	struct iommu_domain *iommu;
+
 	/** @debugfs_root: root directory of komeda debugfs */
 	struct dentry *debugfs_root;
 };
drivers/gpu/drm/arm/display/komeda/komeda_framebuffer.c +2 -0
index d5822a3..360ab70 100644
@@ -201,6 +201,8 @@ struct drm_framebuffer *
 		goto err_cleanup;
 	}
 
+	kfb->is_va = mdev->iommu ? true : false;
+
 	return &kfb->base;
 
 err_cleanup:
drivers/gpu/drm/arm/display/komeda/komeda_framebuffer.h +0 -0
index 6cbb2f6..f4046e2 100644

drivers/gpu/drm/arm/display/komeda/komeda_framebuffer.h struct komeda_fb { · line 28

Quoted 8 lines
drivers/gpu/drm/arm/display/komeda/komeda_framebuffer.h +2 -0
@@ -21,6 +21,8 @@ struct komeda_fb {
 	 * extends drm_format_info for komeda specific information
 	 */
 	const struct komeda_format_caps *format_caps;
+	/** @is_va: if smmu is enabled, it will be true */
+	bool is_va;
 	/** @aligned_w: aligned frame buffer width */
 	u32 aligned_w;
 	/** @aligned_h: aligned frame buffer height */

Looks good to me.

James.

Signature · 5 lines
Reviewed-by: James Qian Wang (Arm Technology China) <[email protected]>
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
maintainer
#3 lore raw

Re: [PATCH v1 1/2] drm/komeda: Adds SMMU support

In reply to Lowry Li (Arm Technology China)

Hi Lowry,

Quoted 79 lines · Lowry Li (Arm Technology China)

Adds iommu_connect and disconnect for SMMU support, and configures TBU translation once SMMU has been attached to the display device.

---
 .../gpu/drm/arm/display/komeda/d71/d71_component.c |  5 +++
 drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c   | 49 ++++++++++++++++++++++
 drivers/gpu/drm/arm/display/komeda/komeda_dev.c    | 17 ++++++++
 drivers/gpu/drm/arm/display/komeda/komeda_dev.h    |  7 ++++
 .../drm/arm/display/komeda/komeda_framebuffer.c    |  2 +
 .../drm/arm/display/komeda/komeda_framebuffer.h    |  2 +
 6 files changed, 82 insertions(+)
drivers/gpu/drm/arm/display/komeda/d71/d71_component.c +5 -0
index 33ca171..9065040 100644
@@ -215,6 +215,8 @@ static void d71_layer_update(struct komeda_component *c,
 	malidp_write32(reg, LAYER_FMT, kfb->format_caps->hw_id);
 	malidp_write32(reg, BLK_IN_SIZE, HV_SIZE(st->hsize, st->vsize));
 
+	if (kfb->is_va)
+		ctrl |= L_TBU_EN;
 	malidp_write32_mask(reg, BLK_CONTROL, ctrl_mask, ctrl);
 }
 
@@ -348,6 +350,9 @@ static void d71_wb_layer_update(struct komeda_component *c,
 			       fb->pitches[i] & 0xFFFF);
 	}
 
+	if (kfb->is_va)
+		ctrl |= LW_TBU_EN;
+
 	malidp_write32(reg, LAYER_FMT, kfb->format_caps->hw_id);
 	malidp_write32(reg, BLK_IN_SIZE, HV_SIZE(st->hsize, st->vsize));
 	malidp_write32(reg, BLK_INPUT_ID0, to_d71_input_id(&state->inputs[0]));
drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c +35 -0
index 9603de9..45c98a7 100644
@@ -517,6 +517,53 @@ static void d71_init_fmt_tbl(struct komeda_dev *mdev)
 	table->n_formats = ARRAY_SIZE(d71_format_caps_table);
 }
 
+static int d71_connect_iommu(struct komeda_dev *mdev)
+{
+	struct d71_dev *d71 = mdev->chip_data;
+	u32 __iomem *reg = d71->gcu_addr;
+	u32 check_bits = (d71->num_pipelines == 2) ?
+			 GCU_STATUS_TCS0 | GCU_STATUS_TCS1 : GCU_STATUS_TCS0;
+	int i, ret;
+
+	if (!d71->integrates_tbu)
+		return -1;
+
+	malidp_write32_mask(reg, BLK_CONTROL, 0x7, TBU_CONNECT_MODE);
+
+	ret = dp_wait_cond(has_bits(check_bits, malidp_read32(reg, BLK_STATUS)),
+			100, 1000, 1000);
+	if (ret <= 0) {
+		DRM_ERROR("connect to TCU timeout!\n");
+		malidp_write32_mask(reg, BLK_CONTROL, 0x7, INACTIVE_MODE);
+		return -ETIMEDOUT;
+	}
+
+	for (i = 0; i < d71->num_pipelines; i++)
+		malidp_write32_mask(d71->pipes[i]->lpu_addr, LPU_TBU_CONTROL,
+				    LPU_TBU_CTRL_TLBPEN, LPU_TBU_CTRL_TLBPEN);
+	return 0;
+}
+
+static int d71_disconnect_iommu(struct komeda_dev *mdev)
+{
+	struct d71_dev *d71 = mdev->chip_data;
+	u32 __iomem *reg = d71->gcu_addr;
+	u32 check_bits = (d71->num_pipelines == 2) ?
+			 GCU_STATUS_TCS0 | GCU_STATUS_TCS1 : GCU_STATUS_TCS0;
+	int ret;
+

drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c static void d71_init_fmt_tbl(struct komeda_dev *mdev) · line 564

Quoted 10 lines
drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c +10 -0
+	malidp_write32_mask(reg, BLK_CONTROL, 0x7, TBU_DISCONNECT_MODE);
+
+	ret = dp_wait_cond(((malidp_read32(reg, BLK_STATUS) & check_bits) == 0),
+			100, 1000, 1000);
+	if (ret <= 0) {
+		DRM_ERROR("disconnect from TCU timeout!\n");
+		malidp_write32_mask(reg, BLK_CONTROL, 0x7, INACTIVE_MODE);
+	}
+
+	return ret > 0 ? 0 : -1;

For consistency with d71_connect_iommu() you should return -ETIMEDOUT as well. I'm sending a patch to convert dp_wait_cond() to return that when it times out, so we can be consistent in the future.

Quoted 20 lines
drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c +4 -0
+}
+
 static struct komeda_dev_funcs d71_chip_funcs = {
 	.init_format_table = d71_init_fmt_tbl,
 	.enum_resources	= d71_enum_resources,
@@ -527,6 +574,8 @@ static void d71_init_fmt_tbl(struct komeda_dev *mdev)
 	.on_off_vblank	= d71_on_off_vblank,
 	.change_opmode	= d71_change_opmode,
 	.flush		= d71_flush,
+	.connect_iommu	= d71_connect_iommu,
+	.disconnect_iommu = d71_disconnect_iommu,
 };
 
 struct komeda_dev_funcs *
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +0 -0
index e4e5b58..2d97c82 100644
@@ -251,6 +251,18 @@ struct komeda_dev *komeda_dev_create(struct device *dev)
 	dev->dma_parms = &mdev->dma_parms;

drivers/gpu/drm/arm/display/komeda/komeda_dev.c struct komeda_dev *komeda_dev_create(struct device *dev) · line 261

Quoted 10 lines
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +8 -0
 	dma_set_max_seg_size(dev, DMA_BIT_MASK(32));
 
+	mdev->iommu = iommu_get_domain_for_dev(mdev->dev);
+	if (!mdev->iommu)
+		DRM_INFO("continue without IOMMU support!\n");
+
+	if (mdev->iommu && mdev->funcs->connect_iommu) {
+		err = mdev->funcs->connect_iommu(mdev);
+		if (err) {
+			DRM_ERROR("connect iommu failed.\n");

connect_iommu() has already printed a DRM_ERROR(), do we need another one here?

drivers/gpu/drm/arm/display/komeda/komeda_dev.c struct komeda_dev *komeda_dev_create(struct device *dev) · line 262

Quoted 1 line
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +1 -0
+			goto err_cleanup;

err_cleanup doesn't set the new mdev->iommu to NULL, forgot to add it?

drivers/gpu/drm/arm/display/komeda/komeda_dev.c void komeda_dev_destroy(struct komeda_dev *mdev) · line 297

Quoted 13 lines
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +6 -0
+		}
+	}
+
 	err = sysfs_create_group(&dev->kobj, &komeda_sysfs_attr_group);
 	if (err) {
 		DRM_ERROR("create sysfs group failed.\n");
@@ -280,6 +292,11 @@ void komeda_dev_destroy(struct komeda_dev *mdev)
 	debugfs_remove_recursive(mdev->debugfs_root);
 #endif
 
+	if (mdev->iommu && mdev->funcs->disconnect_iommu)
+		if (mdev->funcs->disconnect_iommu(mdev))
+			DRM_ERROR("disconnect iommu failed.\n");

Same comment an in komeda_dev_create(), disconnect_iommu() already printed a DRM_ERROR()

Quoted 59 lines
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +2 -0
+	mdev->iommu = NULL;
+
 	for (i = 0; i < mdev->n_pipelines; i++) {
 		komeda_pipeline_destroy(mdev, mdev->pipelines[i]);
 		mdev->pipelines[i] = NULL;
drivers/gpu/drm/arm/display/komeda/komeda_dev.h +7 -0
index 83ace71..dac1eda 100644
@@ -92,6 +92,10 @@ struct komeda_dev_funcs {
 	int (*enum_resources)(struct komeda_dev *mdev);
 	/** @cleanup: call to chip to cleanup komeda_dev->chip data */
 	void (*cleanup)(struct komeda_dev *mdev);
+	/** @connect_iommu: Optional, connect to external iommu */
+	int (*connect_iommu)(struct komeda_dev *mdev);
+	/** @disconnect_iommu: Optional, disconnect to external iommu */
+	int (*disconnect_iommu)(struct komeda_dev *mdev);
 	/**
 	 * @irq_handler:
 	 *
@@ -184,6 +188,9 @@ struct komeda_dev {
 	 */
 	void *chip_data;
 
+	/** @iommu: iommu domain */
+	struct iommu_domain *iommu;
+
 	/** @debugfs_root: root directory of komeda debugfs */
 	struct dentry *debugfs_root;
 };
drivers/gpu/drm/arm/display/komeda/komeda_framebuffer.c +2 -0
index d5822a3..360ab70 100644
@@ -201,6 +201,8 @@ struct drm_framebuffer *
 		goto err_cleanup;
 	}
 
+	kfb->is_va = mdev->iommu ? true : false;
+
 	return &kfb->base;
 
 err_cleanup:
drivers/gpu/drm/arm/display/komeda/komeda_framebuffer.h +2 -0
index 6cbb2f6..f4046e2 100644
@@ -21,6 +21,8 @@ struct komeda_fb {
 	 * extends drm_format_info for komeda specific information
 	 */
 	const struct komeda_format_caps *format_caps;
+	/** @is_va: if smmu is enabled, it will be true */
+	bool is_va;
 	/** @aligned_w: aligned frame buffer width */
 	u32 aligned_w;
 	/** @aligned_h: aligned frame buffer height */
Signature · 1 line
1.9.1

Best regards,
Liviu

Signature · 8 lines
====================
| I would like to |
| fix the world,  |
| but they're not |
| giving me the   |
 \ source code!  /
  ---------------
    ¯\_(ツ)_/¯
#4 lore raw

Re: [PATCH v1 1/2] drm/komeda: Adds SMMU support

Quoted 88 lines · Liviu Dudau

Hi Lowry,

Quoted 85 lines · Lowry Li (Arm Technology China)

Adds iommu_connect and disconnect for SMMU support, and configures TBU translation once SMMU has been attached to the display device.

---
 .../gpu/drm/arm/display/komeda/d71/d71_component.c |  5 +++
 drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c   | 49 ++++++++++++++++++++++
 drivers/gpu/drm/arm/display/komeda/komeda_dev.c    | 17 ++++++++
 drivers/gpu/drm/arm/display/komeda/komeda_dev.h    |  7 ++++
 .../drm/arm/display/komeda/komeda_framebuffer.c    |  2 +
 .../drm/arm/display/komeda/komeda_framebuffer.h    |  2 +
 6 files changed, 82 insertions(+)
drivers/gpu/drm/arm/display/komeda/d71/d71_component.c +5 -0
index 33ca171..9065040 100644
@@ -215,6 +215,8 @@ static void d71_layer_update(struct komeda_component *c,
 	malidp_write32(reg, LAYER_FMT, kfb->format_caps->hw_id);
 	malidp_write32(reg, BLK_IN_SIZE, HV_SIZE(st->hsize, st->vsize));
 
+	if (kfb->is_va)
+		ctrl |= L_TBU_EN;
 	malidp_write32_mask(reg, BLK_CONTROL, ctrl_mask, ctrl);
 }
 
@@ -348,6 +350,9 @@ static void d71_wb_layer_update(struct komeda_component *c,
 			       fb->pitches[i] & 0xFFFF);
 	}
 
+	if (kfb->is_va)
+		ctrl |= LW_TBU_EN;
+
 	malidp_write32(reg, LAYER_FMT, kfb->format_caps->hw_id);
 	malidp_write32(reg, BLK_IN_SIZE, HV_SIZE(st->hsize, st->vsize));
 	malidp_write32(reg, BLK_INPUT_ID0, to_d71_input_id(&state->inputs[0]));
drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c +41 -0
index 9603de9..45c98a7 100644
@@ -517,6 +517,53 @@ static void d71_init_fmt_tbl(struct komeda_dev *mdev)
 	table->n_formats = ARRAY_SIZE(d71_format_caps_table);
 }
 
+static int d71_connect_iommu(struct komeda_dev *mdev)
+{
+	struct d71_dev *d71 = mdev->chip_data;
+	u32 __iomem *reg = d71->gcu_addr;
+	u32 check_bits = (d71->num_pipelines == 2) ?
+			 GCU_STATUS_TCS0 | GCU_STATUS_TCS1 : GCU_STATUS_TCS0;
+	int i, ret;
+
+	if (!d71->integrates_tbu)
+		return -1;
+
+	malidp_write32_mask(reg, BLK_CONTROL, 0x7, TBU_CONNECT_MODE);
+
+	ret = dp_wait_cond(has_bits(check_bits, malidp_read32(reg, BLK_STATUS)),
+			100, 1000, 1000);
+	if (ret <= 0) {
+		DRM_ERROR("connect to TCU timeout!\n");
+		malidp_write32_mask(reg, BLK_CONTROL, 0x7, INACTIVE_MODE);
+		return -ETIMEDOUT;
+	}
+
+	for (i = 0; i < d71->num_pipelines; i++)
+		malidp_write32_mask(d71->pipes[i]->lpu_addr, LPU_TBU_CONTROL,
+				    LPU_TBU_CTRL_TLBPEN, LPU_TBU_CTRL_TLBPEN);
+	return 0;
+}
+
+static int d71_disconnect_iommu(struct komeda_dev *mdev)
+{
+	struct d71_dev *d71 = mdev->chip_data;
+	u32 __iomem *reg = d71->gcu_addr;
+	u32 check_bits = (d71->num_pipelines == 2) ?
+			 GCU_STATUS_TCS0 | GCU_STATUS_TCS1 : GCU_STATUS_TCS0;
+	int ret;
+
+	malidp_write32_mask(reg, BLK_CONTROL, 0x7, TBU_DISCONNECT_MODE);
+
+	ret = dp_wait_cond(((malidp_read32(reg, BLK_STATUS) & check_bits) == 0),
+			100, 1000, 1000);
+	if (ret <= 0) {
+		DRM_ERROR("disconnect from TCU timeout!\n");
Quoted 9 lines

drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c static void d71_init_fmt_tbl(struct komeda_dev *mdev) · line 564

Quoted 4 lines
drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c +4 -0
+		malidp_write32_mask(reg, BLK_CONTROL, 0x7, INACTIVE_MODE);
+	}
+
+	return ret > 0 ? 0 : -1;

For consistency with d71_connect_iommu() you should return -ETIMEDOUT as well. I'm sending a patch to convert dp_wait_cond() to return that when it times out, so we can be consistent in the future.

Hi Liviu,

OK, will change here to return -ETIMEDOUT. Thanks for this correction.

Quoted 22 lines
Quoted 22 lines
drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c +4 -0
+}
+
 static struct komeda_dev_funcs d71_chip_funcs = {
 	.init_format_table = d71_init_fmt_tbl,
 	.enum_resources	= d71_enum_resources,
@@ -527,6 +574,8 @@ static void d71_init_fmt_tbl(struct komeda_dev *mdev)
 	.on_off_vblank	= d71_on_off_vblank,
 	.change_opmode	= d71_change_opmode,
 	.flush		= d71_flush,
+	.connect_iommu	= d71_connect_iommu,
+	.disconnect_iommu = d71_disconnect_iommu,
 };
 
 struct komeda_dev_funcs *
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +0 -0
index e4e5b58..2d97c82 100644
@@ -251,6 +251,18 @@ struct komeda_dev *komeda_dev_create(struct device *dev)
 	dev->dma_parms = &mdev->dma_parms;
 	dma_set_max_seg_size(dev, DMA_BIT_MASK(32));
 
Quoted 11 lines

drivers/gpu/drm/arm/display/komeda/komeda_dev.c struct komeda_dev *komeda_dev_create(struct device *dev) · line 261

Quoted 8 lines
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +8 -0
+	mdev->iommu = iommu_get_domain_for_dev(mdev->dev);
+	if (!mdev->iommu)
+		DRM_INFO("continue without IOMMU support!\n");
+
+	if (mdev->iommu && mdev->funcs->connect_iommu) {
+		err = mdev->funcs->connect_iommu(mdev);
+		if (err) {
+			DRM_ERROR("connect iommu failed.\n");

connect_iommu() has already printed a DRM_ERROR(), do we need another one here?

Will remove this printing code.

Quoted 3 lines

drivers/gpu/drm/arm/display/komeda/komeda_dev.c struct komeda_dev *komeda_dev_create(struct device *dev) · line 262

Quoted 1 line
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +1 -0
+			goto err_cleanup;

err_cleanup doesn't set the new mdev->iommu to NULL, forgot to add it?

Will set mdev->iommu to NULL in komeda_dev_destroy(). Thanks for pointing this out.

Quoted 91 lines
Quoted 9 lines
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +3 -0
+		}
+	}
+
 	err = sysfs_create_group(&dev->kobj, &komeda_sysfs_attr_group);
 	if (err) {
 		DRM_ERROR("create sysfs group failed.\n");

drivers/gpu/drm/arm/display/komeda/komeda_dev.c void komeda_dev_destroy(struct komeda_dev *mdev) · line 297

Quoted 6 lines
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +3 -0
@@ -280,6 +292,11 @@ void komeda_dev_destroy(struct komeda_dev *mdev)
 	debugfs_remove_recursive(mdev->debugfs_root);
 #endif
 
+	if (mdev->iommu && mdev->funcs->disconnect_iommu)
+		if (mdev->funcs->disconnect_iommu(mdev))
+			DRM_ERROR("disconnect iommu failed.\n");

Same comment an in komeda_dev_create(), disconnect_iommu() already printed a DRM_ERROR()

Quoted 59 lines
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +2 -0
+	mdev->iommu = NULL;
+
 	for (i = 0; i < mdev->n_pipelines; i++) {
 		komeda_pipeline_destroy(mdev, mdev->pipelines[i]);
 		mdev->pipelines[i] = NULL;
drivers/gpu/drm/arm/display/komeda/komeda_dev.h +7 -0
index 83ace71..dac1eda 100644
@@ -92,6 +92,10 @@ struct komeda_dev_funcs {
 	int (*enum_resources)(struct komeda_dev *mdev);
 	/** @cleanup: call to chip to cleanup komeda_dev->chip data */
 	void (*cleanup)(struct komeda_dev *mdev);
+	/** @connect_iommu: Optional, connect to external iommu */
+	int (*connect_iommu)(struct komeda_dev *mdev);
+	/** @disconnect_iommu: Optional, disconnect to external iommu */
+	int (*disconnect_iommu)(struct komeda_dev *mdev);
 	/**
 	 * @irq_handler:
 	 *
@@ -184,6 +188,9 @@ struct komeda_dev {
 	 */
 	void *chip_data;
 
+	/** @iommu: iommu domain */
+	struct iommu_domain *iommu;
+
 	/** @debugfs_root: root directory of komeda debugfs */
 	struct dentry *debugfs_root;
 };
drivers/gpu/drm/arm/display/komeda/komeda_framebuffer.c +2 -0
index d5822a3..360ab70 100644
@@ -201,6 +201,8 @@ struct drm_framebuffer *
 		goto err_cleanup;
 	}
 
+	kfb->is_va = mdev->iommu ? true : false;
+
 	return &kfb->base;
 
 err_cleanup:
drivers/gpu/drm/arm/display/komeda/komeda_framebuffer.h +2 -0
index 6cbb2f6..f4046e2 100644
@@ -21,6 +21,8 @@ struct komeda_fb {
 	 * extends drm_format_info for komeda specific information
 	 */
 	const struct komeda_format_caps *format_caps;
+	/** @is_va: if smmu is enabled, it will be true */
+	bool is_va;
 	/** @aligned_w: aligned frame buffer width */
 	u32 aligned_w;
 	/** @aligned_h: aligned frame buffer height */
Signature · 1 line
1.9.1

Best regards,
Liviu

Signature · 8 lines
====================
| I would like to |
| fix the world,  |
| but they're not |
| giving me the   |
 \ source code!  /
  ---------------
    ¯\_(ツ)_/¯
Signature · 6 lines
Regards,
Lowry
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#5 lore raw

Re: [PATCH v1 1/2] drm/komeda: Adds SMMU support

In reply to Liviu Dudau

Hi Liviu,

Please ignore last email and please find the latest feedback inline as below.

Quoted 88 lines · Liviu Dudau

Hi Lowry,

Quoted 85 lines · Lowry Li (Arm Technology China)

Adds iommu_connect and disconnect for SMMU support, and configures TBU translation once SMMU has been attached to the display device.

---
 .../gpu/drm/arm/display/komeda/d71/d71_component.c |  5 +++
 drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c   | 49 ++++++++++++++++++++++
 drivers/gpu/drm/arm/display/komeda/komeda_dev.c    | 17 ++++++++
 drivers/gpu/drm/arm/display/komeda/komeda_dev.h    |  7 ++++
 .../drm/arm/display/komeda/komeda_framebuffer.c    |  2 +
 .../drm/arm/display/komeda/komeda_framebuffer.h    |  2 +
 6 files changed, 82 insertions(+)
drivers/gpu/drm/arm/display/komeda/d71/d71_component.c +5 -0
index 33ca171..9065040 100644
@@ -215,6 +215,8 @@ static void d71_layer_update(struct komeda_component *c,
 	malidp_write32(reg, LAYER_FMT, kfb->format_caps->hw_id);
 	malidp_write32(reg, BLK_IN_SIZE, HV_SIZE(st->hsize, st->vsize));
 
+	if (kfb->is_va)
+		ctrl |= L_TBU_EN;
 	malidp_write32_mask(reg, BLK_CONTROL, ctrl_mask, ctrl);
 }
 
@@ -348,6 +350,9 @@ static void d71_wb_layer_update(struct komeda_component *c,
 			       fb->pitches[i] & 0xFFFF);
 	}
 
+	if (kfb->is_va)
+		ctrl |= LW_TBU_EN;
+
 	malidp_write32(reg, LAYER_FMT, kfb->format_caps->hw_id);
 	malidp_write32(reg, BLK_IN_SIZE, HV_SIZE(st->hsize, st->vsize));
 	malidp_write32(reg, BLK_INPUT_ID0, to_d71_input_id(&state->inputs[0]));
drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c +41 -0
index 9603de9..45c98a7 100644
@@ -517,6 +517,53 @@ static void d71_init_fmt_tbl(struct komeda_dev *mdev)
 	table->n_formats = ARRAY_SIZE(d71_format_caps_table);
 }
 
+static int d71_connect_iommu(struct komeda_dev *mdev)
+{
+	struct d71_dev *d71 = mdev->chip_data;
+	u32 __iomem *reg = d71->gcu_addr;
+	u32 check_bits = (d71->num_pipelines == 2) ?
+			 GCU_STATUS_TCS0 | GCU_STATUS_TCS1 : GCU_STATUS_TCS0;
+	int i, ret;
+
+	if (!d71->integrates_tbu)
+		return -1;
+
+	malidp_write32_mask(reg, BLK_CONTROL, 0x7, TBU_CONNECT_MODE);
+
+	ret = dp_wait_cond(has_bits(check_bits, malidp_read32(reg, BLK_STATUS)),
+			100, 1000, 1000);
+	if (ret <= 0) {
+		DRM_ERROR("connect to TCU timeout!\n");
+		malidp_write32_mask(reg, BLK_CONTROL, 0x7, INACTIVE_MODE);
+		return -ETIMEDOUT;
+	}
+
+	for (i = 0; i < d71->num_pipelines; i++)
+		malidp_write32_mask(d71->pipes[i]->lpu_addr, LPU_TBU_CONTROL,
+				    LPU_TBU_CTRL_TLBPEN, LPU_TBU_CTRL_TLBPEN);
+	return 0;
+}
+
+static int d71_disconnect_iommu(struct komeda_dev *mdev)
+{
+	struct d71_dev *d71 = mdev->chip_data;
+	u32 __iomem *reg = d71->gcu_addr;
+	u32 check_bits = (d71->num_pipelines == 2) ?
+			 GCU_STATUS_TCS0 | GCU_STATUS_TCS1 : GCU_STATUS_TCS0;
+	int ret;
+
+	malidp_write32_mask(reg, BLK_CONTROL, 0x7, TBU_DISCONNECT_MODE);
+
+	ret = dp_wait_cond(((malidp_read32(reg, BLK_STATUS) & check_bits) == 0),
+			100, 1000, 1000);
+	if (ret <= 0) {
+		DRM_ERROR("disconnect from TCU timeout!\n");
Quoted 9 lines

drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c static void d71_init_fmt_tbl(struct komeda_dev *mdev) · line 564

Quoted 4 lines
drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c +4 -0
+		malidp_write32_mask(reg, BLK_CONTROL, 0x7, INACTIVE_MODE);
+	}
+
+	return ret > 0 ? 0 : -1;

For consistency with d71_connect_iommu() you should return -ETIMEDOUT as well. I'm sending a patch to convert dp_wait_cond() to return that when it times out, so we can be consistent in the future.

Yes, will change to use -ETIMEDOUT.

Quoted 22 lines
Quoted 22 lines
drivers/gpu/drm/arm/display/komeda/d71/d71_dev.c +4 -0
+}
+
 static struct komeda_dev_funcs d71_chip_funcs = {
 	.init_format_table = d71_init_fmt_tbl,
 	.enum_resources	= d71_enum_resources,
@@ -527,6 +574,8 @@ static void d71_init_fmt_tbl(struct komeda_dev *mdev)
 	.on_off_vblank	= d71_on_off_vblank,
 	.change_opmode	= d71_change_opmode,
 	.flush		= d71_flush,
+	.connect_iommu	= d71_connect_iommu,
+	.disconnect_iommu = d71_disconnect_iommu,
 };
 
 struct komeda_dev_funcs *
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +0 -0
index e4e5b58..2d97c82 100644
@@ -251,6 +251,18 @@ struct komeda_dev *komeda_dev_create(struct device *dev)
 	dev->dma_parms = &mdev->dma_parms;
 	dma_set_max_seg_size(dev, DMA_BIT_MASK(32));
 
Quoted 11 lines

drivers/gpu/drm/arm/display/komeda/komeda_dev.c struct komeda_dev *komeda_dev_create(struct device *dev) · line 261

Quoted 8 lines
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +8 -0
+	mdev->iommu = iommu_get_domain_for_dev(mdev->dev);
+	if (!mdev->iommu)
+		DRM_INFO("continue without IOMMU support!\n");
+
+	if (mdev->iommu && mdev->funcs->connect_iommu) {
+		err = mdev->funcs->connect_iommu(mdev);
+		if (err) {
+			DRM_ERROR("connect iommu failed.\n");

connect_iommu() has already printed a DRM_ERROR(), do we need another one here?

This log printing is necessary at core layer for the case that some other chip layer code doesn't have error messages. So suggest keeping this code here.

Quoted 5 lines

drivers/gpu/drm/arm/display/komeda/komeda_dev.c struct komeda_dev *komeda_dev_create(struct device *dev) · line 262

Quoted 1 line
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +1 -0
+			goto err_cleanup;

err_cleanup doesn't set the new mdev->iommu to NULL, forgot to add it?

Sorry, I forgot adding this. Will set to NULL here once connected failed. Thanks again.

Quoted 89 lines

drivers/gpu/drm/arm/display/komeda/komeda_dev.c void komeda_dev_destroy(struct komeda_dev *mdev) · line 297

Quoted 13 lines
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +6 -0
+		}
+	}
+
 	err = sysfs_create_group(&dev->kobj, &komeda_sysfs_attr_group);
 	if (err) {
 		DRM_ERROR("create sysfs group failed.\n");
@@ -280,6 +292,11 @@ void komeda_dev_destroy(struct komeda_dev *mdev)
 	debugfs_remove_recursive(mdev->debugfs_root);
 #endif
 
+	if (mdev->iommu && mdev->funcs->disconnect_iommu)
+		if (mdev->funcs->disconnect_iommu(mdev))
+			DRM_ERROR("disconnect iommu failed.\n");

Same comment an in komeda_dev_create(), disconnect_iommu() already printed a DRM_ERROR()

Quoted 59 lines
drivers/gpu/drm/arm/display/komeda/komeda_dev.c +2 -0
+	mdev->iommu = NULL;
+
 	for (i = 0; i < mdev->n_pipelines; i++) {
 		komeda_pipeline_destroy(mdev, mdev->pipelines[i]);
 		mdev->pipelines[i] = NULL;
drivers/gpu/drm/arm/display/komeda/komeda_dev.h +7 -0
index 83ace71..dac1eda 100644
@@ -92,6 +92,10 @@ struct komeda_dev_funcs {
 	int (*enum_resources)(struct komeda_dev *mdev);
 	/** @cleanup: call to chip to cleanup komeda_dev->chip data */
 	void (*cleanup)(struct komeda_dev *mdev);
+	/** @connect_iommu: Optional, connect to external iommu */
+	int (*connect_iommu)(struct komeda_dev *mdev);
+	/** @disconnect_iommu: Optional, disconnect to external iommu */
+	int (*disconnect_iommu)(struct komeda_dev *mdev);
 	/**
 	 * @irq_handler:
 	 *
@@ -184,6 +188,9 @@ struct komeda_dev {
 	 */
 	void *chip_data;
 
+	/** @iommu: iommu domain */
+	struct iommu_domain *iommu;
+
 	/** @debugfs_root: root directory of komeda debugfs */
 	struct dentry *debugfs_root;
 };
drivers/gpu/drm/arm/display/komeda/komeda_framebuffer.c +2 -0
index d5822a3..360ab70 100644
@@ -201,6 +201,8 @@ struct drm_framebuffer *
 		goto err_cleanup;
 	}
 
+	kfb->is_va = mdev->iommu ? true : false;
+
 	return &kfb->base;
 
 err_cleanup:
drivers/gpu/drm/arm/display/komeda/komeda_framebuffer.h +2 -0
index 6cbb2f6..f4046e2 100644
@@ -21,6 +21,8 @@ struct komeda_fb {
 	 * extends drm_format_info for komeda specific information
 	 */
 	const struct komeda_format_caps *format_caps;
+	/** @is_va: if smmu is enabled, it will be true */
+	bool is_va;
 	/** @aligned_w: aligned frame buffer width */
 	u32 aligned_w;
 	/** @aligned_h: aligned frame buffer height */
Signature · 1 line
1.9.1

Best regards,
Liviu

Signature · 8 lines
====================
| I would like to |
| fix the world,  |
| but they're not |
| giving me the   |
 \ source code!  /
  ---------------
    ¯\_(ツ)_/¯
Signature · 6 lines
Regards,
Lowry
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#6 lore raw

PATCH 2/2 dt/bindings: drm/komeda: Adds SMMU support for D71 devicetree

In reply to Lowry Li (Arm Technology China)

Updates the device-tree doc about how to enable SMMU by devicetree.

---
 Documentation/devicetree/bindings/display/arm,komeda.txt | 7 +++++++
 1 file changed, 7 insertions(+)
Documentation/devicetree/bindings/display/arm,komeda.txt +7 -0
index 02b2265..b12c045 100644
@@ -11,6 +11,10 @@ Required properties:
       - "pclk": for the APB interface clock
 - #address-cells: Must be 1
 - #size-cells: Must be 0
+- iommus: configure the stream id to IOMMU, Must be configured if want to
+    enable iommu in display. for how to configure this node please reference
+        devicetree/bindings/iommu/arm,smmu-v3.txt,
+        devicetree/bindings/iommu/iommu.txt
 
 Required properties for sub-node: pipeline@nq
 Each device contains one or two pipeline sub-nodes (at least one), each
@@ -44,6 +48,9 @@ Example:
 		interrupts = <0 168 4>;
 		clocks = <&dpu_mclk>, <&dpu_aclk>;
 		clock-names = "mclk", "pclk";
+		iommus = <&smmu 0>, <&smmu 1>, <&smmu 2>, <&smmu 3>,
+			<&smmu 4>, <&smmu 5>, <&smmu 6>, <&smmu 7>,
+			<&smmu 8>, <&smmu 9>;
 
 		dp0_pipe0: pipeline@0 {
 			clocks = <&fpgaosc2>, <&dpu_aclk>;
Signature · 6 lines
1.9.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#7 lore raw

Re: [v1, 2/2] dt/bindings: drm/komeda: Adds SMMU support for D71 devicetree

Quoted 26 lines · Lowry Li (Arm Technology China)

Updates the device-tree doc about how to enable SMMU by devicetree.

---
 Documentation/devicetree/bindings/display/arm,komeda.txt | 7 +++++++
 1 file changed, 7 insertions(+)
Signature · 1 line
1.9.1
Documentation/devicetree/bindings/display/arm,komeda.txt +4 -0
index 02b2265..b12c045 100644
@@ -11,6 +11,10 @@ Required properties:
       - "pclk": for the APB interface clock
 - #address-cells: Must be 1
 - #size-cells: Must be 0
+- iommus: configure the stream id to IOMMU, Must be configured if want to
+    enable iommu in display. for how to configure this node please reference
+        devicetree/bindings/iommu/arm,smmu-v3.txt,
+        devicetree/bindings/iommu/iommu.txt
 
 Required properties for sub-node: pipeline@nq
 Each device contains one or two pipeline sub-nodes (at least one), each

Documentation/devicetree/bindings/display/arm,komeda.txt Example: · line 56

Quoted 9 lines
Documentation/devicetree/bindings/display/arm,komeda.txt +3 -0
@@ -44,6 +48,9 @@ Example:
 		interrupts = <0 168 4>;
 		clocks = <&dpu_mclk>, <&dpu_aclk>;
 		clock-names = "mclk", "pclk";
+		iommus = <&smmu 0>, <&smmu 1>, <&smmu 2>, <&smmu 3>,
+			<&smmu 4>, <&smmu 5>, <&smmu 6>, <&smmu 7>,
+			<&smmu 8>, <&smmu 9>;
 
 		dp0_pipe0: pipeline@0 {
 			clocks = <&fpgaosc2>, <&dpu_aclk>;

Looks good to me

James

Signature · 1 line
Reviewed-by: James Qian Wang (Arm Technology China) <[email protected]>
maintainer Reviewed-by on v1 2/2
#8 lore raw

Re: [PATCH v1 2/2] dt/bindings: drm/komeda: Adds SMMU support for D71 devicetree

In reply to Lowry Li (Arm Technology China)
Quoted 3 lines · Lowry Li (Arm Technology China)

Updates the device-tree doc about how to enable SMMU by devicetree.

Best regards,
Liviu

Quoted 32 lines
---
 Documentation/devicetree/bindings/display/arm,komeda.txt | 7 +++++++
 1 file changed, 7 insertions(+)
Documentation/devicetree/bindings/display/arm,komeda.txt +7 -0
index 02b2265..b12c045 100644
@@ -11,6 +11,10 @@ Required properties:
       - "pclk": for the APB interface clock
 - #address-cells: Must be 1
 - #size-cells: Must be 0
+- iommus: configure the stream id to IOMMU, Must be configured if want to
+    enable iommu in display. for how to configure this node please reference
+        devicetree/bindings/iommu/arm,smmu-v3.txt,
+        devicetree/bindings/iommu/iommu.txt
 
 Required properties for sub-node: pipeline@nq
 Each device contains one or two pipeline sub-nodes (at least one), each
@@ -44,6 +48,9 @@ Example:
 		interrupts = <0 168 4>;
 		clocks = <&dpu_mclk>, <&dpu_aclk>;
 		clock-names = "mclk", "pclk";
+		iommus = <&smmu 0>, <&smmu 1>, <&smmu 2>, <&smmu 3>,
+			<&smmu 4>, <&smmu 5>, <&smmu 6>, <&smmu 7>,
+			<&smmu 8>, <&smmu 9>;
 
 		dp0_pipe0: pipeline@0 {
 			clocks = <&fpgaosc2>, <&dpu_aclk>;
Signature · 1 line
1.9.1
Signature · 8 lines
====================
| I would like to |
| fix the world,  |
| but they're not |
| giving me the   |
 \ source code!  /
  ---------------
    ¯\_(ツ)_/¯