spl: at91: add support for SPL_AT91_MCK_BYPASS
PATCH 1/2 spl: at91: add support for SPL_AT91_MCK_BYPASS
From: Eugen Hristev <[email protected]>
By default the configuration of the PMC is to have an external crystal connected that requires driving on both XIN and XOUT pins.
The bypass configuration means that only XIN will be used, the SoC will not do any driving, and the XIN needs to be provided with a proper signal. This is the MOSCXTBY bit in the PMC main clock generator register. The SPL needs to properly initialize the PMC registers before switching to external clock signal and raising the clock to the cruise speed.
Also created Kconfig for this specific configuration. By default this is disabled.
--- arch/arm/mach-at91/spl_atmel.c | 8 ++++++++ common/spl/Kconfig | 12 ++++++++++++ 2 files changed, 20 insertions(+)
arch/arm/mach-at91/spl_atmel.c +8 -0
@@ -44,7 +44,15 @@ static void switch_to_main_crystal_osc(void)#endif tmp =readl (&pmc->mor); +/* +* some boards have an external oscillator with driving. +* in this case we need to disable the internal SoC driving (bypass mode) +*/ +#if defined(CONFIG_SPL_AT91_MCK_BYPASS ) + tmp |=AT91_PMC_MOR_OSCBYPASS ; +#else tmp &= ~AT91_PMC_MOR_OSCBYPASS ; +#endif tmp &= ~AT91_PMC_MOR_KEY (0xff ); tmp |=AT91_PMC_MOR_KEY (0x37 );writel (tmp, &pmc->mor);
common/spl/Kconfig +12 -0
@@ -1151,5 +1151,17 @@ config TPL_YMODEM_SUPPORT endif # TPL +config SPL_AT91_MCK_BYPASS + bool "Use external clock signal as a source of main clock for AT91 platforms" + depends on ARCH_AT91 + default n + help + Use external 8 to 24 Mhz clock signal as source of main clock instead + of an external crystal oscillator. + This option disables the internal driving on the XOUT pin. + The external source has to provide a stable clock on the XIN pin. + If this option is disabled, the SoC expects a crystal oscillator + that needs driving on both XIN and XOUT lines. + endif # SPL endmenu
Signature · 1 line
2.7.4
PATCH 1/2 spl: at91: add support for SPL_AT91_MCK_BYPASS
Quoted 10 lines · On 24.05.2019 09:47, Eugen Hristev - M18282 wrote:
From: Eugen Hristev <[email protected]>
By default the configuration of the PMC is to have an external crystal connected that requires driving on both XIN and XOUT pins.
The bypass configuration means that only XIN will be used, the SoC will not do any driving, and the XIN needs to be provided with a proper signal. This is the MOSCXTBY bit in the PMC main clock generator register. The SPL needs to properly initialize the PMC registers before switching to external clock signal and raising the clock to the cruise speed.
Quoted 5 lines
Also created
Kconfigfor this specific configuration. By default this is disabled.Signed-off-by Eugen Hristev <[email protected]>---
Applied both patches in series to u-boot-atmel/master
PATCH 2/2 configs: at91: sama5d2_icp: enable CONFIG_SPL_AT91_MCK_BYPASS and resync
In reply to Eugen.Hristev at microchip.comFrom: Eugen Hristev <[email protected]>
Enabled CONFIG_SPL_AT91_MCK_BYPASS and resync with savedefconfig
--- configs/sama5d2_icp_mmc_defconfig | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
configs/sama5d2_icp_mmc_defconfig +2 -1
@@ -23,12 +23,12 @@ CONFIG_SD_BOOT=y CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y # CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_SPL_TEXT_BASE=0x200000 CONFIG_SPL_SEPARATE_BSS=y CONFIG_SPL_DISPLAY_PRINT=y # CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set CONFIG_SPL_RAM_SUPPORT=y CONFIG_SPL_RAM_DEVICE=y +CONFIG_SPL_AT91_MCK_BYPASS=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMI is not set
@@ -75,3 +75,4 @@ CONFIG_TIMER=y CONFIG_SPL_TIMER=y CONFIG_ATMEL_PIT_TIMER=y CONFIG_OF_LIBFDT_OVERLAY=y +# CONFIG_EFI_LOADER_HII is not set
Signature · 1 line
2.7.4