ath11k: fix Block comments warnings
PATCH 1/1 ath11k: fix Block comments warnings
drivers/net/wireless/ath/ath11k/hal_desc.h:1382: Block comments should align the * on each line drivers/net/wireless/ath/ath11k/hal_desc.h:1440: Block comments should align the * on each line drivers/net/wireless/ath/ath11k/mac.c:3233: Block comments use a trailing */ on a separate line
Signed-off-by Karthikeyan Periyasamy <[email protected]>
--- drivers/net/wireless/ath/ath11k/hal_desc.h | 208 ++++++++++++++--------------- drivers/net/wireless/ath/ath11k/mac.c | 3 +- 2 files changed, 105 insertions(+), 106 deletions(-)
drivers/net/wireless/ath/ath11k/hal_desc.h +103 -105
@@ -1378,46 +1378,45 @@ struct hal_ce_srng_dest_desc {u32 buffer_addr_info;/* %HAL_CE_DEST_DESC_ADDR_INFO_ */ } __packed; -/* -* hal_ce_srng_dest_desc -* -* dst_buffer_low -* LSB 32 bits of the 40 Bit Pointer to the Destination -* buffer -* -* dst_buffer_high -* MSB 8 bits of the 40 Bit Pointer to the Destination -* buffer -* -* ce_res_4 -* Reserved -* -* ring_id -* The buffer pointer ring ID. -* 0 refers to the IDLE ring -* 1 - N refers to other rings -* Helps with debugging when dumping ring contents. -* -* looping_count -* A count value that indicates the number of times the -* producer of entries into the Ring has looped around the -* ring. -* -* At initialization time, this value is set to 0. On the -* first loop, this value is set to 1. After the max value is -* reached allowed by the number of bits for this field, the -* count value continues with 0 again. -* -* In case SW is the consumer of the ring entries, it can -* use this field to figure out up to where the producer of -* entries has created new entries. This eliminates the need to -* check where the head pointer' of the ring is located once -* the SW starts processing an interrupt indicating that new -* entries have been put into this ring... -* -* Also note that SW if it wants only needs to look at the -* LSB bit of this count value. -*/ +/* hal_ce_srng_dest_desc +* +* dst_buffer_low +* LSB 32 bits of the 40 Bit Pointer to the Destination +* buffer +* +* dst_buffer_high +* MSB 8 bits of the 40 Bit Pointer to the Destination +* buffer +* +* ce_res_4 +* Reserved +* +* ring_id +* The buffer pointer ring ID. +* 0 refers to the IDLE ring +* 1 - N refers to other rings +* Helps with debugging when dumping ring contents. +* +* looping_count +* A count value that indicates the number of times the +* producer of entries into the Ring has looped around the +* ring. +* +* At initialization time, this value is set to 0. On the +* first loop, this value is set to 1. After the max value is +* reached allowed by the number of bits for this field, the +* count value continues with 0 again. +* +* In case SW is the consumer of the ring entries, it can +* use this field to figure out up to where the producer of +* entries has created new entries. This eliminates the need to +* check where the head pointer' of the ring is located once +* the SW starts processing an interrupt indicating that new +* entries have been put into this ring... +* +* Also note that SW if it wants only needs to look at the +* LSB bit of this count value. +*/ #define HAL_CE_DST_STATUS_DESC_FLAGS_HASH_EN BIT(8)#define HAL_CE_DST_STATUS_DESC_FLAGS_BYTE_SWAP BIT(9)
@@ -1436,71 +1435,70 @@ struct hal_ce_srng_dst_status_desc {u32 meta_info;/* HAL_CE_DST_STATUS_DESC_META_INFO_ */ } __packed; -/* -* hal_ce_srng_dst_status_desc -* -* ce_res_5 -* Reserved -* -* toeplitz_en -* -* src_swap -* Source memory buffer swapped -* -* dest_swap -* Destination memory buffer swapped -* -* gather -* Gather of multiple copy engine source descriptors to one -* destination enabled -* -* ce_res_6 -* Reserved -* -* length -* Sum of all the Lengths of the source descriptor in the -* gather chain -* -* toeplitz_hash_0 -* 32 LS bits of 64 bit Toeplitz LFSR hash result -* -* toeplitz_hash_1 -* 32 MS bits of 64 bit Toeplitz LFSR hash result -* -* fw_metadata -* Meta data used by FW -* In case of gather field in first source ring entry of -* the gather copy cycle in taken into account. -* -* ce_res_7 -* Reserved -* -* ring_id -* The buffer pointer ring ID. -* 0 refers to the IDLE ring -* 1 - N refers to other rings -* Helps with debugging when dumping ring contents. -* -* looping_count -* A count value that indicates the number of times the -* producer of entries into the Ring has looped around the -* ring. -* -* At initialization time, this value is set to 0. On the -* first loop, this value is set to 1. After the max value is -* reached allowed by the number of bits for this field, the -* count value continues with 0 again. -* -* In case SW is the consumer of the ring entries, it can -* use this field to figure out up to where the producer of -* entries has created new entries. This eliminates the need to -* check where the head pointer' of the ring is located once -* the SW starts processing an interrupt indicating that new -* entries have been put into this ring... -* -* Also note that SW if it wants only needs to look at the -* LSB bit of this count value. -*/ +/* hal_ce_srng_dst_status_desc +* +* ce_res_5 +* Reserved +* +* toeplitz_en +* +* src_swap +* Source memory buffer swapped +* +* dest_swap +* Destination memory buffer swapped +* +* gather +* Gather of multiple copy engine source descriptors to one +* destination enabled +* +* ce_res_6 +* Reserved +* +* length +* Sum of all the Lengths of the source descriptor in the +* gather chain +* +* toeplitz_hash_0 +* 32 LS bits of 64 bit Toeplitz LFSR hash result +* +* toeplitz_hash_1 +* 32 MS bits of 64 bit Toeplitz LFSR hash result +* +* fw_metadata +* Meta data used by FW +* In case of gather field in first source ring entry of +* the gather copy cycle in taken into account. +* +* ce_res_7 +* Reserved +* +* ring_id +* The buffer pointer ring ID. +* 0 refers to the IDLE ring +* 1 - N refers to other rings +* Helps with debugging when dumping ring contents. +* +* looping_count +* A count value that indicates the number of times the +* producer of entries into the Ring has looped around the +* ring. +* +* At initialization time, this value is set to 0. On the +* first loop, this value is set to 1. After the max value is +* reached allowed by the number of bits for this field, the +* count value continues with 0 again. +* +* In case SW is the consumer of the ring entries, it can +* use this field to figure out up to where the producer of +* entries has created new entries. This eliminates the need to +* check where the head pointer' of the ring is located once +* the SW starts processing an interrupt indicating that new +* entries have been put into this ring... +* +* Also note that SW if it wants only needs to look at the +* LSB bit of this count value. +*/ #define HAL_TX_RATE_STATS_INFO0_VALID BIT(0)#define HAL_TX_RATE_STATS_INFO0_BW GENMASK(2, 1)
drivers/net/wireless/ath/ath11k/mac.c +2 -1
@@ -3106,7 +3106,8 @@ static void ath11k_mac_setup_ht_vht_cap(struct ath11k *ar,static int ath11k_check_chain_mask (struct ath11k *ar,u32 ant,bool is_tx_ant) {/* TODO: Check the request chainmask against the supported -* chainmask table which is advertised in extented_service_ready event */ +* chainmask table which is advertised in extented_service_ready event +*/ return 0 ; }
Signature · 7 lines
1.9.1 _______________________________________________ ath11k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath11k