hwmon: (lm75) Support configuring the sample time for various chips
Guenter Roeck
maintainerPATCH 1/4 hwmon: (lm75) Support configuring the sample time for various chips
The conversion (sample) time is configurable for several chips supported by the lm75 driver. With the necessary infrastructure in place, enable this support for all chips using the configuration register for this purpose.
DS1775:
Conversion time: 187.5, 375, 750, 1500 ms Sensor resolution: 9, 10, 11, 12 bit DS75, STDS75: Conversion time: 150, 300, 600, 1200 ms Sensor resolution: 9, 10, 11, 12 bit DS7505: Conversion time: 25, 50, 100, 200 ms Sensor resolution: 9, 10, 11, 12 bit MCP980[0123]: Conversion time: 75, 150, 300, 600 ms Sensor resolution: 9, 10, 11, 12 bit TMP100, TMP101: Conversion time: 75, 150, 300, 600 ms Sensor resolution: 9, 10, 11, 12 bit TMP75, TMP105, TMP175, TMP275: Conversion time: 38, 75, 150, 300 ms Sensor resolution: 9, 10, 11, 12 bit
While doing this, it became obvious that the masks and values to set the converion (sample) time is similar for all those chips, and that other chips with configurable sample times will need separate code anyway. For that reason, replace the sample_set_masks and sample_clr_mask configuration parameters with a single array and with a constant.
--- drivers/hwmon/lm75.c | 83 +++++++++++++++++++++++++++++++++++----------------- 1 file changed, 56 insertions(+), 27 deletions(-)
drivers/hwmon/lm75.c +56 -27
@@ -73,10 +73,6 @@ enum lm75_type { /* keep sorted in alphabetical order */* @sample_times: All the possible sample times to be set. Mandatory if * num_sample_times is larger than 1. If set, number of * entries must match num_sample_times. -* @sample_set_masks: All the set_masks for the possible sample times. -* Mandatory if num_sample_times is larger than 1. -* If set, number of entries must match num_sample_times. -* @sample_clr_mask: Clear mask used to set the sample time. */ struct lm75_params {
@@ -88,8 +84,6 @@ struct lm75_params {unsigned int default_sample_time;u8 num_sample_times;const unsigned int *sample_times; -const u8 *sample_set_masks; -u8 sample_clr_mask; };/* Addresses scanned */
@@ -115,6 +109,11 @@ struct lm75_data { };/*-----------------------------------------------------------------------*/ + +static const u8 lm75_sample_set_masks[] = {0 <<5 ,1 <<5 ,2 <<5 ,3 <<5 }; + +#define LM75_SAMPLE_CLEAR_MASK (3 << 5) +/* The structure below stores the configuration values of the supported devices. * In case of being supported multiple configurations, the default one must * always be the first element of the array
@@ -129,19 +128,28 @@ static const struct lm75_params device_params[] = { .clr_mask = 3 << 5, .set_mask = 2 << 5, /* 11-bit mode */ .default_resolution = 11, - .default_sample_time = MSEC_PER_SEC, + .default_sample_time = 750, + .num_sample_times = 4, + .sample_times = (unsigned int []){ 188, 375, 750, 1500 }, + .resolutions = (u8 []) {9, 10, 11, 12 }, }, [ds75] = { .clr_mask = 3 << 5, .set_mask = 2 << 5, /* 11-bit mode */ .default_resolution = 11, - .default_sample_time = MSEC_PER_SEC, + .default_sample_time = 600, + .num_sample_times = 4, + .sample_times = (unsigned int []){ 150, 300, 600, 1200 }, + .resolutions = (u8 []) {9, 10, 11, 12 }, }, [stds75] = { .clr_mask = 3 << 5, .set_mask = 2 << 5, /* 11-bit mode */ .default_resolution = 11, - .default_sample_time = MSEC_PER_SEC, + .default_sample_time = 600, + .num_sample_times = 4, + .sample_times = (unsigned int []){ 150, 300, 600, 1200 }, + .resolutions = (u8 []) {9, 10, 11, 12 }, }, [stlm75] = { .default_resolution = 9,
@@ -150,7 +158,10 @@ static const struct lm75_params device_params[] = { [ds7505] = { .set_mask = 3 << 5, /* 12-bit mode*/ .default_resolution = 12, - .default_sample_time = MSEC_PER_SEC / 4, + .default_sample_time = 200, + .num_sample_times = 4, + .sample_times = (unsigned int []){ 25, 50, 100, 200 }, + .resolutions = (u8 []) {9, 10, 11, 12 }, }, [g751] = { .default_resolution = 9,
@@ -194,56 +205,74 @@ static const struct lm75_params device_params[] = { .clr_mask = 1 << 7, /* not one-shot mode */ .default_resolution = 12, .resolution_limits = 9, - .default_sample_time = MSEC_PER_SEC, + .default_sample_time = 240, + .num_sample_times = 4, + .sample_times = (unsigned int []){ 75, 150, 300, 600 }, + .resolutions = (u8 []) {9, 10, 11, 12 }, }, [tmp100] = { .set_mask = 3 << 5, /* 12-bit mode */ .clr_mask = 1 << 7, /* not one-shot mode */ .default_resolution = 12, - .default_sample_time = MSEC_PER_SEC, + .default_sample_time = 320, + .num_sample_times = 4, + .sample_times = (unsigned int []){ 75, 150, 300, 600 }, + .resolutions = (u8 []) {9, 10, 11, 12 }, }, [tmp101] = { .set_mask = 3 << 5, /* 12-bit mode */ .clr_mask = 1 << 7, /* not one-shot mode */ .default_resolution = 12, - .default_sample_time = MSEC_PER_SEC, + .default_sample_time = 320, + .num_sample_times = 4, + .sample_times = (unsigned int []){ 75, 150, 300, 600 }, + .resolutions = (u8 []) {9, 10, 11, 12 }, }, - [tmp112] = { + [tmp105] = { .set_mask = 3 << 5, /* 12-bit mode */ - .clr_mask = 1 << 7, /* no one-shot mode*/ + .clr_mask = 1 << 7, /* not one-shot mode*/ .default_resolution = 12, - .default_sample_time = MSEC_PER_SEC / 4, + .default_sample_time = 220, + .num_sample_times = 4, + .sample_times = (unsigned int []){ 38, 75, 150, 300 }, + .resolutions = (u8 []) {9, 10, 11, 12 }, }, - [tmp105] = { + [tmp112] = { .set_mask = 3 << 5, /* 12-bit mode */ - .clr_mask = 1 << 7, /* not one-shot mode*/ + .clr_mask = 1 << 7, /* no one-shot mode*/ .default_resolution = 12, - .default_sample_time = MSEC_PER_SEC / 2, + .default_sample_time = MSEC_PER_SEC / 4, }, [tmp175] = { .set_mask = 3 << 5, /* 12-bit mode */ .clr_mask = 1 << 7, /* not one-shot mode*/ .default_resolution = 12, - .default_sample_time = MSEC_PER_SEC / 2, + .default_sample_time = 220, + .num_sample_times = 4, + .sample_times = (unsigned int []){ 38, 75, 150, 300 }, + .resolutions = (u8 []) {9, 10, 11, 12 }, }, [tmp275] = { .set_mask = 3 << 5, /* 12-bit mode */ .clr_mask = 1 << 7, /* not one-shot mode*/ .default_resolution = 12, - .default_sample_time = MSEC_PER_SEC / 2, + .default_sample_time = 220, + .num_sample_times = 4, + .sample_times = (unsigned int []){ 38, 75, 150, 300 }, + .resolutions = (u8 []) {9, 10, 11, 12 }, }, [tmp75] = { .set_mask = 3 << 5, /* 12-bit mode */ .clr_mask = 1 << 7, /* not one-shot mode*/ .default_resolution = 12, - .default_sample_time = MSEC_PER_SEC / 2, + .default_sample_time = 220, + .num_sample_times = 4, + .sample_times = (unsigned int []){ 38, 75, 150, 300 }, + .resolutions = (u8 []) {9, 10, 11, 12 }, }, [tmp75b] = { /* not one-shot mode, Conversion rate 37Hz */ .clr_mask = 1 << 7 | 3 << 5, .default_resolution = 12, - .sample_set_masks = (u8 []){0 <<5 ,1 <<5 ,2 <<5 , - 3 << 5 }, - .sample_clr_mask = 3 << 5, .default_sample_time = MSEC_PER_SEC / 37, .sample_times = (unsigned int []){MSEC_PER_SEC /37 ,MSEC_PER_SEC /18 ,
@@ -371,8 +400,8 @@ static int lm75_write_chip(struct device *dev, u32 attr, long val) (int)data->params->num_sample_times); err =lm75_write_config (data, - data->params->sample_set_masks[index], - data->params->sample_clr_mask); + lm75_sample_set_masks[index], +LM75_SAMPLE_CLEAR_MASK );if (err)return err; data->sample_time = data->params->sample_times[index];
Signature · 1 line
2.7.4
Guenter Roeck
maintainerPATCH 2/4 hwmon: (lm75) Move updating the sample interval to its own function
We'll need per-chip handling for updating the sample interval. To prepare for it, separate the code implementing it into its own function.
--- drivers/hwmon/lm75.c | 33 +++++++++++++++++++-------------- 1 file changed, 19 insertions(+), 14 deletions(-)
drivers/hwmon/lm75.c +19 -14
@@ -388,27 +388,32 @@ static int lm75_write_temp(struct device *dev, u32 attr, long temp)return regmap_write (data->regmap, reg, (u16 )temp); } -static int lm75_write_chip (struct device *dev,u32 attr,long val) +static int lm75_update_interval (struct device *dev,long val) {struct lm75_data *data =dev_get_drvdata (dev);u8 index;s32 err; -switch (attr) { -case hwmon_chip_update_interval: - index =find_closest (val, data->params->sample_times, - (int )data->params->num_sample_times); + index =find_closest (val, data->params->sample_times, + (int )data->params->num_sample_times); - err =lm75_write_config (data, - lm75_sample_set_masks[index], -LM75_SAMPLE_CLEAR_MASK ); -if (err) -return err; - data->sample_time = data->params->sample_times[index]; + err =lm75_write_config (data, lm75_sample_set_masks[index], +LM75_SAMPLE_CLEAR_MASK ); +if (err) +return err; -if (data->params->resolutions) - data->resolution = data->params->resolutions[index]; -break ; + data->sample_time = data->params->sample_times[index]; +if (data->params->resolutions) + data->resolution = data->params->resolutions[index]; + +return 0 ; +} + +static int lm75_write_chip (struct device *dev,u32 attr,long val) +{ +switch (attr) { +case hwmon_chip_update_interval: +return lm75_update_interval (dev, val);default :return -EINVAL ; }
Signature · 1 line
2.7.4
Guenter Roeck
maintainerPATCH 3/4 hwmon: (lm75) Add support for writing conversion time for TMP112
In reply to Guenter RoeckTMP112 uses an uncommon method to write the conversion time: its configuration register is 16 bit wide, and the conversion time is configured in its second byte.
--- drivers/hwmon/lm75.c | 35 ++++++++++++++++++++++++++--------- 1 file changed, 26 insertions(+), 9 deletions(-)
drivers/hwmon/lm75.c +26 -9
@@ -242,6 +242,8 @@ static const struct lm75_params device_params[] = { .clr_mask = 1 << 7, /* no one-shot mode*/ .default_resolution = 12, .default_sample_time = MSEC_PER_SEC / 4, + .num_sample_times = 4, + .sample_times = (unsigned int []){ 125, 250, 1000, 4000 }, }, [tmp175] = { .set_mask = 3 << 5, /* 12-bit mode */
@@ -391,21 +393,36 @@ static int lm75_write_temp(struct device *dev, u32 attr, long temp)static int lm75_update_interval (struct device *dev,long val) {struct lm75_data *data =dev_get_drvdata (dev); +unsigned int reg;u8 index;s32 err; index =find_closest (val, data->params->sample_times, (int )data->params->num_sample_times); - err =lm75_write_config (data, lm75_sample_set_masks[index], -LM75_SAMPLE_CLEAR_MASK ); -if (err) -return err; - - data->sample_time = data->params->sample_times[index]; -if (data->params->resolutions) - data->resolution = data->params->resolutions[index]; +switch (data->kind) { +default : + err =lm75_write_config (data, lm75_sample_set_masks[index], +LM75_SAMPLE_CLEAR_MASK ); +if (err) +return err; + data->sample_time = data->params->sample_times[index]; +if (data->params->resolutions) + data->resolution = data->params->resolutions[index]; +break ; +case tmp112: + err =regmap_read (data->regmap,LM75_REG_CONF , ®); +if (err <0 ) +return err; + reg &= ~0x00c0 ; + reg |= (3 - index) <<6 ; + err =regmap_write (data->regmap,LM75_REG_CONF , reg); +if (err <0 ) +return err; + data->sample_time = data->params->sample_times[index]; +break ; + }return 0 ; }
@@ -489,7 +506,7 @@ static bool lm75_is_writeable_reg(struct device *dev, unsigned int reg)static bool lm75_is_volatile_reg (struct device *dev,unsigned int reg) { -return reg ==LM75_REG_TEMP ; +return reg ==LM75_REG_TEMP || reg ==LM75_REG_CONF ; }static const struct regmap_config lm75_regmap_config = {
Signature · 1 line
2.7.4
Guenter Roeck
maintainerPATCH 4/4 hwmon: (lm75) Add support for writing sampling period on PCT2075
In reply to Guenter RoeckFor PCT7027, the sampling period is configured using a dedicated register.
--- drivers/hwmon/lm75.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-)
drivers/hwmon/lm75.c +14 -1
@@ -95,6 +95,7 @@ static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, 0x4c,#define LM75_REG_CONF 0x01#define LM75_REG_HYST 0x02#define LM75_REG_MAX 0x03 +#define PCT2075_REG_IDLE 0x04/* Each client has this additional data */ struct lm75_data {
@@ -199,6 +200,11 @@ static const struct lm75_params device_params[] = { [pct2075] = { .default_resolution = 11, .default_sample_time = MSEC_PER_SEC / 10, + .num_sample_times = 31, + .sample_times = (unsigned int []){100 ,200 ,300 ,400 ,500 ,600 , +700 ,800 ,900 ,1000 ,1100 ,1200 ,1300 ,1400 ,1500 ,1600 ,1700 , +1800 ,1900 ,2000 ,2100 ,2200 ,2300 ,2400 ,2500 ,2600 ,2700 , + 2800, 2900, 3000, 3100 }, }, [mcp980x] = { .set_mask = 3 << 5, /* 12-bit mode */
@@ -422,6 +428,13 @@ static int lm75_update_interval(struct device *dev, long val)return err; data->sample_time = data->params->sample_times[index];break ; +case pct2075: + err =i2c_smbus_write_byte_data (data->client,PCT2075_REG_IDLE , + index +1 ); +if (err) +return err; + data->sample_time = data->params->sample_times[index]; +break ; }return 0 ; }
@@ -512,7 +525,7 @@ static bool lm75_is_volatile_reg(struct device *dev, unsigned int reg)static const struct regmap_config lm75_regmap_config = { .reg_bits =8 , .val_bits =16 , - .max_register =LM75_REG_MAX , + .max_register =PCT2075_REG_IDLE , .writeable_reg = lm75_is_writeable_reg, .volatile_reg = lm75_is_volatile_reg, .val_format_endian =REGMAP_ENDIAN_BIG ,
Signature · 1 line
2.7.4