Skip to contentSkip to conversation

arm: dts: Stratix10: change pad skew values for EMAC0 PHY driver

PATCH New Ooi 2 participants 3 messages Nov 21, 2019 – Nov 22, 2019 Arm (32-bit)

lore
Share & tools
lore

Ooi

#0 lore raw

PATCH 1/1 arm: dts: Stratix10: change pad skew values for EMAC0 PHY driver

The HPS EMAC0 drive strength is changed to 4mA because the initial 8mA drive strength has caused CE test to fail. This requires changes on the pad skew for EMAC0 PHY driver. Based on several measurements done, Tx clock does not require the extra 0.96ns delay which was needed in Arria10.

---
 arch/arm/dts/socfpga_stratix10_socdk.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/dts/socfpga_stratix10_socdk.dts +1 -1
index 8c7b422..b7b48a5 100755
@@ -74,7 +74,7 @@
 			rxd2-skew-ps = <420>; /* 0ps */
 			rxd3-skew-ps = <420>; /* 0ps */
 			txen-skew-ps = <0>; /* -420ps */
-			txc-skew-ps = <1860>; /* 960ps */
+			txc-skew-ps = <900>; /* 0ps */
 			rxdv-skew-ps = <420>; /* 0ps */
 			rxc-skew-ps = <1680>; /* 780ps */
 		};
Signature · 1 line
1.9.1
#1 lore raw

PATCH 1/1 arm: dts: Stratix10: change pad skew values for EMAC0 PHY driver

Quoted 11 lines

-----Original Message-----
From: Ooi, Joyce <[email protected]>
Sent: Thursday, November 21, 2019 10:49 PM
To: Tan, Ley Foon <[email protected]>; Ang, Chee Hong <[email protected]>
Cc: Ooi, Joyce <[email protected]>; u-boot at lists.denx.de
Subject: [PATCH] arm: dts: Stratix10: change pad skew values for EMAC0 PHY driver

Quoted 6 lines

The HPS EMAC0 drive strength is changed to 4mA because the initial 8mA drive strength has caused CE test to fail. This requires changes on the pad skew for EMAC0 PHY driver. Based on several measurements done, Tx clock does not require the extra 0.96ns delay which was needed in Arria10.

Regards
Ley Foon

Applied
#2 lore raw

PATCH 1/1 arm: dts: Stratix10: change pad skew values for EMAC0 PHY driver

Quoted 11 lines · Ley Foon
Quoted 11 lines

-----Original Message-----
From: Ooi, Joyce <[email protected]>
Sent: Thursday, November 21, 2019 10:49 PM
To: Tan, Ley Foon <[email protected]>; Ang, Chee Hong <[email protected]>
Cc: Ooi, Joyce <[email protected]>; u-boot at lists.denx.de
Subject: [PATCH] arm: dts: Stratix10: change pad skew values for EMAC0 PHY driver

Quoted 7 lines
Quoted 6 lines

The HPS EMAC0 drive strength is changed to 4mA because the initial 8mA drive strength has caused CE test to fail. This requires changes on the pad skew for EMAC0 PHY driver. Based on several measurements done, Tx clock does not require the extra 0.96ns delay which was needed in Arria10.

Applied, thanks.