scsi: Adjust DBD setting in mode sense for caching mode page per LLD
A message that is not in the archive (sent off-list or not yet received): [email protected]
PATCH v5 1/5 scsi: Adjust DBD setting in mode sense for caching mode page per LLD
UFS JEDEC standards require DBD field to be set to 1 in mode sense command. This patch allows LLD to define the setting of DBD if required.
--- drivers/scsi/scsi_lib.c | 2 ++ include/scsi/scsi_device.h | 1 + 2 files changed, 3 insertions(+)
drivers/scsi/scsi_lib.c +2 -0
@@ -2108,6 +2108,8 @@ void scsi_exit_queue(void)memset (data,0 ,sizeof (*data));memset (&cmd[0 ],0 ,12 ); + + dbd = sdev->set_dbd_for_ms ?8 : dbd; cmd[1 ] = dbd &0x18 ;/* allows DBD and LLBA bits */ cmd[2 ] = modepage;
include/scsi/scsi_device.h +1 -0
@@ -172,6 +172,7 @@ struct scsi_device {* because we did a bus reset. */ unsigned use_10_for_rw:1; /* first try 10-byte read / write */ unsigned use_10_for_ms:1; /* first try 10-byte mode sense/select */ + unsigned set_dbd_for_ms:1; /* Set "DBD" field in mode sense */ unsigned no_report_opcodes:1; /* no REPORT SUPPORTED OPERATION CODES */ unsigned no_write_same:1; /* no WRITE SAME command */ unsigned use_16_for_rw:1; /* Use read/write(16) over read/write(10) */
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
PATCH v5 2/5 scsi: ufs: Use DBD setting in mode sense
In reply to a message not in the archiveUFS standards requires DBD field to be set to 1 in mode sense(10).
Some card vendors are more strict and check the DBD field, hence respond with CHECK_CONDITION (Sense key set to ILLEGAL_REQUEST and ASC set to INVALID FIELD IN CDB).
When host send mode sense for page caching, as a result of the CHECK_CONDITION response, host assumes that the device doesn't support the cache feature and doesn't send SYNCHRONIZE_CACHE commands to flush the device cache. This can result in data corruption in case of sudden power down, when there is data stored in the device cache.
This patch fixes the DBD field setting as required in UFS standards.
--- drivers/scsi/ufs/ufshcd.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/scsi/ufs/ufshcd.c +3 -0
@@ -4596,6 +4596,9 @@ static int ufshcd_slave_alloc(struct scsi_device *sdev)/* Mode sense(6) is not supported by UFS, so use Mode sense(10) */ sdev->use_10_for_ms =1 ; +/* DBD field should be set to 1 in mode sense(10) */ + sdev->set_dbd_for_ms =1 ; +/* allow SCSI layer to restart the device in case of errors */ sdev->allow_restart =1 ;
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
PATCH v5 3/5 scsi: ufs: Release clock if DMA map fails
In reply to a message not in the archiveIn queuecommand path, if DMA map fails, it bails out with clock held. In this case, release the clock to keep its usage paired.
--- drivers/scsi/ufs/ufshcd.c | 1 + 1 file changed, 1 insertion(+)
drivers/scsi/ufs/ufshcd.c +1 -0
@@ -2480,6 +2480,7 @@ static int ufshcd_queuecommand(struct Scsi_Host *host, struct scsi_cmnd *cmd)if (err) { lrbp->cmd =NULL ;clear_bit_unlock (tag, &hba->lrb_in_use); +ufshcd_release (hba); goto out; }/* Make sure descriptors are ready before ringing the doorbell */
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
PATCH v5 4/5 scsi: ufs: Do not clear the DL layer timers
In reply to a message not in the archiveDuring power mode change, PACP_PWR_Req frame sends PAPowerModeUserData parameters (and they are considered valid by device if Flags[4] - UserDataValid bit is set in the same frame). Currently we don't set these PAPowerModeUserData parameters and hardware always sets UserDataValid bit which would clear all the DL layer timeout values of the peer device after the power mode change.
This change sets the PAPowerModeUserData[0..5] to UniPro specification recommended default values, in addition we are also setting the relevant DME_LOCAL_* timer attributes as required by UFS HCI specification.
Reviewed-by Avri Altman <[email protected]>
--- drivers/scsi/ufs/ufshcd.c | 20 ++++++++++++++++++++ drivers/scsi/ufs/unipro.h | 11 +++++++++++ 2 files changed, 31 insertions(+)
drivers/scsi/ufs/ufshcd.c +20 -0
@@ -4084,6 +4084,26 @@ static int ufshcd_change_power_mode(struct ufs_hba *hba,ufshcd_dme_set (hba,UIC_ARG_MIB (PA_HSSERIES ), pwr_mode->hs_rate); +ufshcd_dme_set (hba,UIC_ARG_MIB (PA_PWRMODEUSERDATA0 ), + DL_FC0ProtectionTimeOutVal_Default); +ufshcd_dme_set (hba,UIC_ARG_MIB (PA_PWRMODEUSERDATA1 ), + DL_TC0ReplayTimeOutVal_Default); +ufshcd_dme_set (hba,UIC_ARG_MIB (PA_PWRMODEUSERDATA2 ), + DL_AFC0ReqTimeOutVal_Default); +ufshcd_dme_set (hba,UIC_ARG_MIB (PA_PWRMODEUSERDATA3 ), + DL_FC1ProtectionTimeOutVal_Default); +ufshcd_dme_set (hba,UIC_ARG_MIB (PA_PWRMODEUSERDATA4 ), + DL_TC1ReplayTimeOutVal_Default); +ufshcd_dme_set (hba,UIC_ARG_MIB (PA_PWRMODEUSERDATA5 ), + DL_AFC1ReqTimeOutVal_Default); + +ufshcd_dme_set (hba,UIC_ARG_MIB (DME_LocalFC0ProtectionTimeOutVal), + DL_FC0ProtectionTimeOutVal_Default); +ufshcd_dme_set (hba,UIC_ARG_MIB (DME_LocalTC0ReplayTimeOutVal), + DL_TC0ReplayTimeOutVal_Default); +ufshcd_dme_set (hba,UIC_ARG_MIB (DME_LocalAFC0ReqTimeOutVal), + DL_AFC0ReqTimeOutVal_Default); + ret =ufshcd_uic_change_pwr_mode (hba, pwr_mode->pwr_rx <<4 | pwr_mode->pwr_tx);
drivers/scsi/ufs/unipro.h +11 -0
@@ -161,6 +161,17 @@/* PHY Adapter Protocol Constants */ #define PA_MAXDATALANES 4 +#define DL_FC0ProtectionTimeOutVal_Default 8191 +#define DL_TC0ReplayTimeOutVal_Default 65535 +#define DL_AFC0ReqTimeOutVal_Default 32767 +#define DL_FC1ProtectionTimeOutVal_Default 8191 +#define DL_TC1ReplayTimeOutVal_Default 65535 +#define DL_AFC1ReqTimeOutVal_Default 32767 + +#define DME_LocalFC0ProtectionTimeOutVal 0xD041 +#define DME_LocalTC0ReplayTimeOutVal 0xD042 +#define DME_LocalAFC0ReqTimeOutVal 0xD043 +/* PA power modes */ enum {FAST_MODE =1 ,
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
PATCH v5 5/5 scsi: ufs: Do not free irq in suspend
In reply to a message not in the archiveSince ufshcd irq resource is allocated with the device resource management aware IRQ request implementation, we don't really need to free up irq during suspend, disabling it during suspend and reenabling it during resume should be good enough.
--- drivers/scsi/ufs/ufshcd.c | 18 ++++-------------- 1 file changed, 4 insertions(+), 14 deletions(-)
drivers/scsi/ufs/ufshcd.c +4 -14
@@ -266,26 +266,18 @@ static inline bool ufshcd_valid_tag(struct ufs_hba *hba, int tag)return tag >=0 && tag < hba->nutrs; } -static inline int ufshcd_enable_irq (struct ufs_hba *hba) +static inline void ufshcd_enable_irq (struct ufs_hba *hba) { -int ret =0 ; -if (!hba->is_irq_enabled) { - ret =request_irq (hba->irq, ufshcd_intr,IRQF_SHARED ,UFSHCD , - hba); -if (ret) -dev_err (hba->dev,"%s: request_irq failed, ret=%d\n" , - __func__, ret); +enable_irq (hba->irq); hba->is_irq_enabled = true; } - -return ret; }static inline void ufshcd_disable_irq (struct ufs_hba *hba) {if (hba->is_irq_enabled) { -free_irq (hba->irq, hba); +disable_irq (hba->irq); hba->is_irq_enabled = false; } }
@@ -7930,9 +7922,7 @@ static int ufshcd_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op) goto out;/* enable the host irq as host controller would be active soon */ - ret =ufshcd_enable_irq (hba); -if (ret) - goto disable_irq_and_vops_clks; +ufshcd_enable_irq (hba); ret =ufshcd_vreg_set_hpm (hba);if (ret)
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project