Add support to handle targets without TrustZone
Subsystems (3)
v2 cover Add support to handle targets without TrustZone
The iommu mapping for S2 SIDs are taken care by TrustZone. For the targets which does not have the support of TrustZone, these mappings need to be created in the driver using an iommu domain.
Leaving these SIDs unconfigured will result in a global smmu fault. Hence configuring them for Non-TrustZone targets is mandatory.
Changes from v1:
- Rebase and fix compilation errors on latest ath10k tree tip
Rakesh Pillai (3):
dt-bindings: ath10k: Add wifi-firmware subnode for wifi node
ath10k: Setup the msa resources before qmi init
ath10k: Add support for targets without trustzone
.../bindings/net/wireless/qcom,ath10k.txt | 14 ++ drivers/net/wireless/ath/ath10k/core.h | 5 + drivers/net/wireless/ath/ath10k/qmi.c | 61 +------ drivers/net/wireless/ath/ath10k/qmi.h | 3 - drivers/net/wireless/ath/ath10k/snoc.c | 182 ++++++++++++++++++++- drivers/net/wireless/ath/ath10k/snoc.h | 7 + 6 files changed, 208 insertions(+), 64 deletions(-)
Signature · 1 line
2.7.4
PATCH v2 3/3 ath10k: Add support for targets without trustzone
Add the support to attach and map iommu
domain for targets which do not have the
support of TrustZone.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
--- drivers/net/wireless/ath/ath10k/snoc.c | 118 ++++++++++++++++++++++++++++++++- drivers/net/wireless/ath/ath10k/snoc.h | 7 ++ 2 files changed, 124 insertions(+), 1 deletion(-)
drivers/net/wireless/ath/ath10k/snoc.c +117 -1
@@ -12,6 +12,7 @@#include <linux/property.h> #include <linux/regulator/consumer.h> #include <linux/of_address.h> +#include <linux/iommu.h> #include "ce.h" #include "coredump.h"
@@ -1499,6 +1500,111 @@ static int ath10k_setup_msa_resources(struct ath10k *ar, u32 msa_size)return 0 ; } +static int ath10k_fw_init (struct ath10k *ar) +{ +struct ath10k_snoc *ar_snoc =ath10k_snoc_priv (ar); +struct device *host_dev = &ar_snoc->dev->dev; +struct platform_device_info info; +struct iommu_domain *iommu_dom; +struct platform_device *pdev; +struct device_node *node; +int ret; + + node =of_get_child_by_name (host_dev->of_node,"wifi-firmware" ); +if (!node) { + ar_snoc->use_tz = true; +return 0 ; + } + +memset (&info,0 ,sizeof (info)); + info.fwnode = &node->fwnode; + info.parent = host_dev; + info.name = node->name; + info.dma_mask =DMA_BIT_MASK (32 ); + + pdev =platform_device_register_full (&info); +if (IS_ERR (pdev)) { +of_node_put (node); +return PTR_ERR (pdev); + } + + pdev->dev.of_node = node; + + ret =of_dma_configure (&pdev->dev, node, true); +if (ret) { +ath10k_err (ar,"dma configure fail: %d\n" , ret); + goto err_unregister; + } + + ar_snoc->fw.dev = &pdev->dev; + + iommu_dom =iommu_domain_alloc (&platform_bus_type); +if (!iommu_dom) { +ath10k_err (ar,"failed to allocate iommu domain\n" ); + ret = -ENOMEM ; + goto err_unregister; + } + + ret =iommu_attach_device (iommu_dom, ar_snoc->fw.dev); +if (ret) { +ath10k_err (ar,"could not attach device: %d\n" , ret); + goto err_iommu_free; + } + + ar_snoc->fw.iommu_domain = iommu_dom; + ar_snoc->fw.fw_start_addr = ar->msa.paddr; + + ret =iommu_map (iommu_dom, ar_snoc->fw.fw_start_addr, + ar->msa.paddr, ar->msa.mem_size, +IOMMU_READ |IOMMU_WRITE ); +if (ret) { +ath10k_err (ar,"failed to map firmware region: %d\n" , ret); + goto err_iommu_detach; + } + +of_node_put (node); + +return 0 ; + +err_iommu_detach: +iommu_detach_device (iommu_dom, ar_snoc->fw.dev); + +err_iommu_free: +iommu_domain_free (iommu_dom); + +err_unregister: +platform_device_unregister (pdev); +of_node_put (node); + +return ret; +} + +static int ath10k_fw_deinit (struct ath10k *ar) +{ +struct ath10k_snoc *ar_snoc =ath10k_snoc_priv (ar); +const size_t mapped_size = ar_snoc->fw.mapped_mem_size; +struct iommu_domain *iommu; +size_t unmapped_size; + +if (ar_snoc->use_tz) +return 0 ; + + iommu = ar_snoc->fw.iommu_domain; + + unmapped_size =iommu_unmap (iommu, ar_snoc->fw.fw_start_addr, + mapped_size); +if (unmapped_size != mapped_size) +ath10k_err (ar,"failed to unmap firmware: %zu\n" , + unmapped_size); + +iommu_detach_device (iommu, ar_snoc->fw.dev); +iommu_domain_free (iommu); + +platform_device_unregister (to_platform_device (ar_snoc->fw.dev)); + +return 0 ; +} +static const struct of_device_id ath10k_snoc_dt_match[] = { { .compatible ="qcom,wcn3990-wifi" , .data = &drv_priv,
@@ -1607,16 +1713,25 @@ static int ath10k_snoc_probe(struct platform_device *pdev) goto err_power_off; } + ret =ath10k_fw_init (ar); +if (ret) { +ath10k_err (ar,"failed to initialize firmware: %d\n" , ret); + goto err_power_off; + } + ret =ath10k_qmi_init (ar, msa_size);if (ret) {ath10k_warn (ar,"failed to register wlfw qmi client: %d\n" , ret); - goto err_power_off; + goto err_fw_deinit; }ath10k_dbg (ar,ATH10K_DBG_SNOC ,"snoc probe\n" );return 0 ; +err_fw_deinit: +ath10k_fw_deinit (ar); + err_power_off:ath10k_hw_power_off (ar);
@@ -1648,6 +1763,7 @@ static int ath10k_snoc_remove(struct platform_device *pdev)ath10k_core_unregister (ar);ath10k_hw_power_off (ar); +ath10k_fw_deinit (ar);ath10k_snoc_free_irq (ar);ath10k_snoc_release_resource (ar);ath10k_qmi_deinit (ar);
drivers/net/wireless/ath/ath10k/snoc.h +7 -0
@@ -55,6 +55,13 @@ struct regulator_bulk_data;struct ath10k_snoc {struct platform_device *dev;struct ath10k *ar; +unsigned int use_tz; +struct video_firmware { +struct device *dev; +dma_addr_t fw_start_addr; +struct iommu_domain *iommu_domain; +size_t mapped_mem_size; + } fw;void __iomem *mem;dma_addr_t mem_pa;struct ath10k_snoc_target_info target_info;
Signature · 6 lines
2.7.4 _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
PATCH v2 1/3 dt-bindings: ath10k: Add wifi-firmware subnode for wifi node
In reply to Rakesh PillaiAdd a wifi-firmware subnode for the wifi node.
This wifi-firmware subnode is needed for the
targets which do not support TrustZone.
--- .../devicetree/bindings/net/wireless/qcom,ath10k.txt | 14 ++++++++++++++ 1 file changed, 14 insertions(+)
Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +14 -0
@@ -96,6 +96,17 @@ Optional properties: - qcom,coexist-gpio-pin : gpio pin number information to support coex which will be used by wifi firmware. +* Subnodes +The ath10k wifi node can contain one optional firmware subnode. +Firmware subnode is needed when the platform does not have TustZone. +The firmware subnode must have: + +- iommus: + Usage: required + Value type: <prop-encoded-array> + Definition: A list of phandle and IOMMU specifier pairs. + + Example (to supply PCI based wifi block details): In this example, the node is defined as child node of the PCI controller.
@@ -196,4 +207,7 @@ wifi@18000000 { memory-region = <&wifi_msa_mem>; iommus = <&apps_smmu 0x0040 0x1>; qcom,msa-fixed-perm; + wifi-firmware { + iommus = <&apps_iommu 0xc22 0x1>; + }; };
Signature · 6 lines
2.7.4 _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
PATCH v2 2/3 ath10k: Setup the msa resources before qmi init
In reply to Rakesh PillaiMove the msa resources setup out of qmi init and
setup the msa resources as a part of probe before
the qmi init is done.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
--- drivers/net/wireless/ath/ath10k/core.h | 5 +++ drivers/net/wireless/ath/ath10k/qmi.c | 61 +++++--------------------------- drivers/net/wireless/ath/ath10k/qmi.h | 3 -- drivers/net/wireless/ath/ath10k/snoc.c | 64 ++++++++++++++++++++++++++++++---- 4 files changed, 70 insertions(+), 63 deletions(-)
drivers/net/wireless/ath/ath10k/core.h +5 -0
@@ -949,6 +949,11 @@ struct ath10k {struct ieee80211_hw *hw;struct ieee80211_ops *ops;struct device *dev; +struct msa_region { +dma_addr_t paddr; +u32 mem_size; +void *vaddr; + } msa;u8 mac_addr[ETH_ALEN ];enum ath10k_hw_rev hw_rev;
drivers/net/wireless/ath/ath10k/qmi.c +8 -53
91 lines not on this page · raw message
drivers/net/wireless/ath/ath10k/qmi.h +0 -3
@@ -93,9 +93,6 @@ struct ath10k_qmi {spinlock_t event_lock;/* spinlock for qmi event list */ u32 nr_mem_region;struct ath10k_msa_mem_info mem_region[MAX_NUM_MEMORY_REGIONS ]; -dma_addr_t msa_pa; -u32 msa_mem_size; -void *msa_va;struct ath10k_qmi_chip_info chip_info;struct ath10k_qmi_board_info board_info;struct ath10k_qmi_soc_info soc_info;
drivers/net/wireless/ath/ath10k/snoc.c +57 -7
97 lines not on this page · raw message
Signature · 6 lines
2.7.4 _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
Rob Herring
maintainerRe: [PATCH v2 1/3] dt-bindings: ath10k: Add wifi-firmware subnode for wifi node
In reply to Rakesh PillaiQuoted 32 lines · Rakesh Pillai
Add a wifi-firmware subnode for the wifi node.
This wifi-firmware subnode is needed for the
targets which do not support TrustZone.Signed-off-by Rakesh Pillai <[email protected]>--- .../devicetree/bindings/net/wireless/qcom,ath10k.txt | 14 ++++++++++++++ 1 file changed, 14 insertions(+)Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +11
-0@@ -96,6 +96,17 @@ Optional properties: - qcom,coexist-gpio-pin : gpio pin number information to support coex which will be used by wifi firmware. +* Subnodes +The ath10k wifi node can contain one optional firmware subnode. +Firmware subnode is needed when the platform does not have TustZone. +The firmware subnode must have: + +- iommus: + Usage: required + Value type: <prop-encoded-array> + Definition: A list of phandle and IOMMU specifier pairs. + + Example (to supply PCI based wifi block details): In this example, the node is defined as child node of the PCI controller.
Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt wifi@18000000 { · line 211
Quoted 5 lines
Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +2
-0@@ -196,4 +207,7 @@ wifi@18000000 { memory-region = <&wifi_msa_mem>; iommus = <&apps_smmu 0x0040 0x1>; qcom,msa-fixed-perm; + wifi-firmware { + iommus = <&apps_iommu 0xc22 0x1>;
Why can't you just add a 2nd entry to the existing 'iommus' property?
A driver doing of_dma_configure() is generally not the right thing to do.
Rob
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
RE: [PATCH v2 1/3] dt-bindings: ath10k: Add wifi-firmware subnode for wifi node
Hi Rob,
Comments inline.
Quoted 43 lines
-----Original Message-----
From: Rob Herring <[email protected]>
Sent: Wednesday, April 1, 2020 3:11 AM
To: Rakesh Pillai <[email protected]>
Cc: [email protected]; [email protected]; [email protected]; [email protected]
Subject: Re: [PATCH v2 1/3] dt-bindings: ath10k: Add wifi-firmware subnode for wifi nodeQuoted 7 lines · Rakesh Pillai
Add a wifi-firmware subnode for the wifi node.
This wifi-firmware subnode is needed for the
targets which do not support TrustZone.Signed-off-by Rakesh Pillai <[email protected]>--- .../devicetree/bindings/net/wireless/qcom,ath10k.txt | 14++++++++++++++
Quoted 3 lines
1 file changed, 14 insertions(+)diff --git
a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txtb/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txtQuoted 20 lines
index 71bf91f..65ee68e 100644
Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +11
-0@@ -96,6 +96,17 @@ Optional properties: - qcom,coexist-gpio-pin : gpio pin number information to support coex which will be used by wifi firmware. +* Subnodes +The ath10k wifi node can contain one optional firmware subnode. +Firmware subnode is needed when the platform does not have TustZone. +The firmware subnode must have: + +- iommus: + Usage: required + Value type: <prop-encoded-array> + Definition: A list of phandle and IOMMU specifier pairs. + + Example (to supply PCI based wifi block details):
Quoted 1 line
Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt Optional properties: · line 112
Quoted 1 line
Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +0
-0In this example, the node is defined as child node of the PCI
controller.
Quoted 11 lines
Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt wifi@18000000 { · line 211
Quoted 6 lines
Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +2
-0@@ -196,4 +207,7 @@ wifi@18000000 { memory-region = <&wifi_msa_mem>; iommus = <&apps_smmu 0x0040 0x1>; qcom,msa-fixed-perm; + wifi-firmware { + iommus = <&apps_iommu 0xc22 0x1>;Why can't you just add a 2nd entry to the existing 'iommus' property?
A driver doing
of_dma_configure()is generally not the right thing to do.
The SIDs mentioned in the wifi-firmware node will be belonging to the firmware and not any HLOS.
In other targets with TZ, the hypervisor takes care of configuring the SIDs (for its master).
In this target (sc7180 IDP) we are not having TZ (no hypervisor), hence these need to be configured by HLOS.
The wifi-firmware node is added in-order to differentiate the SID between driver and firmware.
This is same as the approach followed by Venus video driver in the below patch
https://patchwork.kernel.org/patch/11315765/
Quoted 2 lines
Rob
RE: [PATCH v2 3/3] ath10k: Add support for targets without trustzone
In reply to Rakesh PillaiHi Kalle,
I have sent out v3 for this patchset after correcting the firmware structure name which was added in ath10k snoc structure
Thanks,
Rakesh Pillai.
Quoted 208 lines
-----Original Message-----
From: Rakesh Pillai <[email protected]>
Sent: Wednesday, March 25, 2020 4:32 PM
To: [email protected]
Cc: [email protected]; [email protected]; linux- [email protected]; Rakesh Pillai <[email protected]>
Subject: [PATCH v2 3/3] ath10k: Add support for targets without trustzoneAdd the support to attach and map iommu
domain for targets which do not have the
support of TrustZone.Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1Signed-off-by Rakesh Pillai <[email protected]>--- drivers/net/wireless/ath/ath10k/snoc.c | 118 ++++++++++++++++++++++++++++++++- drivers/net/wireless/ath/ath10k/snoc.h | 7 ++ 2 files changed, 124 insertions(+), 1 deletion(-)drivers/net/wireless/ath/ath10k/snoc.c +106
-0@@ -12,6 +12,7 @@#include <linux/property.h> #include <linux/regulator/consumer.h> #include <linux/of_address.h> +#include <linux/iommu.h> #include "ce.h" #include "coredump.h" @@ -1499,6 +1500,111 @@ static int ath10k_setup_msa_resources(struct ath10k *ar, u32 msa_size) return 0; } +static int ath10k_fw_init (struct ath10k *ar) +{ +struct ath10k_snoc *ar_snoc =ath10k_snoc_priv (ar); +struct device *host_dev = &ar_snoc->dev->dev; +struct platform_device_info info; +struct iommu_domain *iommu_dom; +struct platform_device *pdev; +struct device_node *node; +int ret; + + node =of_get_child_by_name (host_dev->of_node,"wifi- firmware"); +if (!node) { + ar_snoc->use_tz = true; +return 0 ; + } + +memset (&info,0 ,sizeof (info)); + info.fwnode = &node->fwnode; + info.parent = host_dev; + info.name = node->name; + info.dma_mask =DMA_BIT_MASK (32 ); + + pdev =platform_device_register_full (&info); +if (IS_ERR (pdev)) { +of_node_put (node); +return PTR_ERR (pdev); + } + + pdev->dev.of_node = node; + + ret =of_dma_configure (&pdev->dev, node, true); +if (ret) { +ath10k_err (ar,"dma configure fail: %d\n" , ret); + goto err_unregister; + } + + ar_snoc->fw.dev = &pdev->dev; + + iommu_dom =iommu_domain_alloc (&platform_bus_type); +if (!iommu_dom) { +ath10k_err (ar,"failed to allocate iommu domain\n" ); + ret = -ENOMEM ; + goto err_unregister; + } + + ret =iommu_attach_device (iommu_dom, ar_snoc->fw.dev); +if (ret) { +ath10k_err (ar,"could not attach device: %d\n" , ret); + goto err_iommu_free; + } + + ar_snoc->fw.iommu_domain = iommu_dom; + ar_snoc->fw.fw_start_addr = ar->msa.paddr; + + ret =iommu_map (iommu_dom, ar_snoc->fw.fw_start_addr, + ar->msa.paddr, ar->msa.mem_size, +IOMMU_READ |IOMMU_WRITE ); +if (ret) { +ath10k_err (ar,"failed to map firmware region: %d\n" , ret); + goto err_iommu_detach; + } + +of_node_put (node); + +return 0 ; + +err_iommu_detach: +iommu_detach_device (iommu_dom, ar_snoc->fw.dev); + +err_iommu_free: +iommu_domain_free (iommu_dom); + +err_unregister: +platform_device_unregister (pdev); +of_node_put (node); + +return ret; +} + +static int ath10k_fw_deinit (struct ath10k *ar) +{ +struct ath10k_snoc *ar_snoc =ath10k_snoc_priv (ar); +const size_t mapped_size = ar_snoc->fw.mapped_mem_size; +struct iommu_domain *iommu; +size_t unmapped_size; + +if (ar_snoc->use_tz) +return 0 ; + + iommu = ar_snoc->fw.iommu_domain; + + unmapped_size =iommu_unmap (iommu, ar_snoc- >fw.fw_start_addr, + mapped_size); +if (unmapped_size != mapped_size) +ath10k_err (ar,"failed to unmap firmware: %zu\n" , + unmapped_size); + +iommu_detach_device (iommu, ar_snoc->fw.dev); +iommu_domain_free (iommu); + +platform_device_unregister (to_platform_device (ar_snoc->fw.dev)); + +return 0 ; +} +static const struct
of_device_idath10k_snoc_dt_match[] = {drivers/net/wireless/ath/ath10k/snoc.c +10
-1{ .compatible = "qcom,wcn3990-wifi", .data = &drv_priv,@@ -1607,16 +1713,25 @@ static int ath10k_snoc_probe(struct platform_device *pdev) goto err_power_off; } + ret =ath10k_fw_init (ar); +if (ret) { +ath10k_err (ar,"failed to initialize firmware: %d\n" , ret); + goto err_power_off; + } + ret =ath10k_qmi_init (ar, msa_size);if (ret) {ath10k_warn (ar,"failed to register wlfw qmi client: %d\n" , ret); - goto err_power_off; + goto err_fw_deinit; }ath10k_dbg (ar,ATH10K_DBG_SNOC ,"snoc probe\n" );return 0 ; +err_fw_deinit: +ath10k_fw_deinit (ar); + err_power_off:drivers/net/wireless/ath/ath10k/snoc.c +1
-0ath10k_hw_power_off (ar);@@ -1648,6 +1763,7 @@ static int ath10k_snoc_remove(struct platform_device *pdev)ath10k_core_unregister (ar );ath10k_hw_power_off (ar); +ath10k_fw_deinit (ar);ath10k_snoc_free_irq (ar);ath10k_snoc_release_resource (ar);drivers/net/wireless/ath/ath10k/snoc.c +0
-0ath10k_qmi_deinit (ar);drivers/net/wireless/ath/ath10k/snoc.h +7
-1@@ -55,6 +55,13 @@ struct regulator_bulk_data;struct ath10k_snoc {struct platform_device *dev;struct ath10k *ar; +unsigned int use_tz; +struct video_firmware { +struct device *dev; +dma_addr_t fw_start_addr; +struct iommu_domain *iommu_domain; +size_t mapped_mem_size; + } fw;void __iomem *mem;dma_addr_t mem_pa;struct ath10k_snoc_target_info target_info; --
Quoted 1 line
2.7.4
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k