Skip to contentSkip to conversation

ADD interconnect support for Qualcomm DWC3 driver

PATCH Superseded Sandeep Maheswaram 2 participants 4 messages Jul 21, 2020

Subsystems (6)

v9 of 11 Superseded Latest is v11 →

lore
Share & tools
lore
#1 lore raw

PATCH v9 1/2 usb: dwc3: qcom: Add interconnect support in dwc3 driver

In reply to Sandeep Maheswaram

Add interconnect support in dwc3-qcom driver to vote for bus bandwidth.

This requires for two different paths - from USB to DDR. The other is from APPS to USB.

---
 drivers/usb/dwc3/dwc3-qcom.c | 127 ++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 125 insertions(+), 2 deletions(-)
drivers/usb/dwc3/dwc3-qcom.c +125 -2
index e1e78e9..82e08ff 100644
@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/extcon.h>
+#include <linux/interconnect.h>
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
 #include <linux/phy/phy.h>
@@ -43,6 +44,14 @@
 #define SDM845_QSCRATCH_SIZE			0x400
 #define SDM845_DWC3_CORE_SIZE			0xcd00
 
+/* Interconnect path bandwidths in MBps */
+#define USB_MEMORY_AVG_HS_BW MBps_to_icc(240)
+#define USB_MEMORY_PEAK_HS_BW MBps_to_icc(700)
+#define USB_MEMORY_AVG_SS_BW  MBps_to_icc(1000)
+#define USB_MEMORY_PEAK_SS_BW MBps_to_icc(2500)
+#define APPS_USB_AVG_BW 0
+#define APPS_USB_PEAK_BW MBps_to_icc(40)
+
 struct dwc3_acpi_pdata {
 	u32			qscratch_base_offset;
 	u32			qscratch_base_size;
@@ -76,6 +85,8 @@ struct dwc3_qcom {
 	enum usb_dr_mode	mode;
 	bool			is_suspended;
 	bool			pm_suspended;
+	struct icc_path		*icc_path_ddr;
+	struct icc_path		*icc_path_apps;
 };
 
 static inline void dwc3_qcom_setbits(void __iomem *base, u32 offset, u32 val)
@@ -190,6 +201,101 @@ static int dwc3_qcom_register_extcon(struct dwc3_qcom *qcom)
 	return 0;
 }
 
+/* Bandwidth levels are set in dwc3_qcom_interconnect_init ,
+ * so just "enable" interconnects.
+ */
+static int dwc3_qcom_interconnect_enable(struct dwc3_qcom *qcom)
+{
+	int ret;
+
+	ret = icc_enable(qcom->icc_path_ddr);
+	if (ret)
+		return ret;
+
+	ret = icc_enable(qcom->icc_path_apps);
+	if (ret)
+		return ret;
+
+	return ret;
+}
+
+/*Disabling the interconnect, will set the bandwidth to 0 */
+static int dwc3_qcom_interconnect_disable(struct dwc3_qcom *qcom)
+{
+	int ret;
+
+	ret = icc_disable(qcom->icc_path_ddr);
+	if (ret)
+		return ret;
+
+	ret = icc_disable(qcom->icc_path_apps);
+	if (ret)
+		return ret;
+
+	return ret;
+}
+
+/**
+ * dwc3_qcom_interconnect_init() - Get interconnect path handles
+ * and set bandwidhth.
+ * @qcom:			Pointer to the concerned usb core.
+ *
+ */
+static int dwc3_qcom_interconnect_init(struct dwc3_qcom *qcom)
+{
+	struct device *dev = qcom->dev;
+	int ret;
+
+	qcom->icc_path_ddr = of_icc_get(dev, "usb-ddr");
+	if (IS_ERR(qcom->icc_path_ddr)) {
+		dev_err(dev, "failed to get usb-ddr path: %ld\n",
+			PTR_ERR(qcom->icc_path_ddr));
+		return PTR_ERR(qcom->icc_path_ddr);
+	}
+
+	qcom->icc_path_apps = of_icc_get(dev, "apps-usb");
+	if (IS_ERR(qcom->icc_path_apps)) {
+		dev_err(dev, "failed to get apps-usb path: %ld\n",
+				PTR_ERR(qcom->icc_path_apps));
+		return PTR_ERR(qcom->icc_path_apps);
+	}
+
+	if (usb_get_maximum_speed(&qcom->dwc3->dev) >= USB_SPEED_SUPER ||
+			usb_get_maximum_speed(&qcom->dwc3->dev) == USB_SPEED_UNKNOWN)
+		ret = icc_set_bw(qcom->icc_path_ddr,
+			USB_MEMORY_AVG_SS_BW, USB_MEMORY_PEAK_SS_BW);
+	else
+		ret = icc_set_bw(qcom->icc_path_ddr,
+			USB_MEMORY_AVG_HS_BW, USB_MEMORY_PEAK_HS_BW);
+
+	if (ret) {
+		dev_err(dev, "failed to set bandwidth for usb-ddr path: %d\n", ret);
+		return ret;
+	}
+
+	ret = icc_set_bw(qcom->icc_path_apps,
+		APPS_USB_AVG_BW, APPS_USB_PEAK_BW);
+
+	if (ret) {
+		dev_err(dev, "failed to set bandwidth for apps-usb path: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * dwc3_qcom_interconnect_exit() - Release interconnect path handles
+ * @qcom:			Pointer to the concerned usb core.
+ *
+ * This function is used to release interconnect path handle.
+ */
+static void dwc3_qcom_interconnect_exit(struct dwc3_qcom *qcom)
+{
+	icc_put(qcom->icc_path_ddr);
+	icc_put(qcom->icc_path_apps);
+}
+
 static void dwc3_qcom_disable_interrupts(struct dwc3_qcom *qcom)
 {
 	if (qcom->hs_phy_irq) {
@@ -239,7 +345,7 @@ static void dwc3_qcom_enable_interrupts(struct dwc3_qcom *qcom)
 static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
 {
 	u32 val;
-	int i;
+	int i, ret;
 
 	if (qcom->is_suspended)
 		return 0;
@@ -251,6 +357,10 @@ static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
 	for (i = qcom->num_clocks - 1; i >= 0; i--)
 		clk_disable_unprepare(qcom->clks[i]);
 
+	ret = dwc3_qcom_interconnect_disable(qcom);
+	if (ret)
+		dev_warn(qcom->dev, "failed to disable interconnect: %d\n", ret);
+
 	qcom->is_suspended = true;
 	dwc3_qcom_enable_interrupts(qcom);
 
@@ -276,6 +386,10 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom)
 		}
 	}
 
+	ret = dwc3_qcom_interconnect_enable(qcom);
+	if (ret)
+		dev_warn(qcom->dev, "failed to enable interconnect: %d\n", ret);
+
 	/* Clear existing events from PHY related to L2 in/out */
 	dwc3_qcom_setbits(qcom->qscratch_base, PWR_EVNT_IRQ_STAT_REG,
 			  PWR_EVNT_LPM_IN_L2_MASK | PWR_EVNT_LPM_OUT_L2_MASK);
@@ -285,6 +399,8 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom)
 	return 0;
 }
 
+
+
 static irqreturn_t qcom_dwc3_resume_irq(int irq, void *data)
 {
 	struct dwc3_qcom *qcom = data;
@@ -638,6 +754,10 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 		goto depopulate;
 	}
 
+	ret = dwc3_qcom_interconnect_init(qcom);
+	if (ret)
+		goto depopulate;
+
 	qcom->mode = usb_get_dr_mode(&qcom->dwc3->dev);
 
 	/* enable vbus override for device mode */
@@ -647,7 +767,7 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 	/* register extcon to override sw_vbus on Vbus change later */
 	ret = dwc3_qcom_register_extcon(qcom);
 	if (ret)
-		goto depopulate;
+		goto interconnect_exit;
 
 	device_init_wakeup(&pdev->dev, 1);
 	qcom->is_suspended = false;
@@ -657,6 +777,8 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 
 	return 0;
 
+interconnect_exit:
+	dwc3_qcom_interconnect_exit(qcom);
 depopulate:
 	if (np)
 		of_platform_depopulate(&pdev->dev);
@@ -687,6 +809,7 @@ static int dwc3_qcom_remove(struct platform_device *pdev)
 	}
 	qcom->num_clocks = 0;
 
+	dwc3_qcom_interconnect_exit(qcom);
 	reset_control_assert(qcom->resets);
 
 	pm_runtime_allow(dev);
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#0 lore raw

v9 cover ADD interconnect support for Qualcomm DWC3 driver

This path series aims to add interconnect support in dwc3-qcom driver on SDM845 and SC7180 SoCs.

Changes from v8 -> v9

Quoted 1 line

Addressed comments from Matthias.

Changes from v7 -> v8

Quoted 1 line

Only driver change is pending all other patches are merged so dropped

from the series.

Quoted 1 line

Removed the device_is_bound call and getting speed from device tree

and rearranged interconnect functions to avoid forward declarations.

Quoted 1 line

Added patch to specify maximum speed for dwc3 DT node.

Changes from v6 -> v7

Quoted 2 lines

[PATCH 2/4] Fixed review comments from Matthias in DWC3 driver. Other patches remain unchanged.

Changes from v5 -> v6

Quoted 4 lines

[PATCH 1/4] Addressed comments from Rob.
[PATCH 2/4] Fixed review comments from Matthias in DWC3 driver. [PATCH 3/4] Ignoring 80 char limit in defining interconnect paths. Added [PATCH 4/4] in this series. Adding interconnect nodes for SC7180.

    Depends on patch https://patchwork.kernel.org/patch/11417989/.	

Changes from v4 -> v5

Quoted 1 line

[PATCH 1/3] Added the interconnect properties in yaml. This patch depends

    on series https://patchwork.kernel.org/cover/11372641/.
Quoted 2 lines

[PATCH 2/3] Fixed review comments from Matthias in DWC3 driver. [PATCH 3/3] Modified as per the new interconnect nodes in sdm845. Depends

    on series https://patchwork.kernel.org/cover/11372211/. 

Changes from v3 -> v4

Quoted 2 lines

Fixed review comments from Matthias
[PATCH 1/3] and [PATCH 3/3] remains unchanged

Changes from v2 -> v3

Quoted 2 lines

Fixed review comments from Matthias and Manu changed the functions prefix from usb_* to dwc3_qcom_*

Changes since V1:

Quoted 2 lines

Comments by Georgi Djakov on "[PATCH 2/3]" addressed [PATCH 1/3] and [PATCH 3/3] remains unchanged

Sandeep Maheswaram (2):
usb: dwc3: qcom: Add interconnect support in dwc3 driver
arm64: dts: qcom: sc7180: Add maximum speed property for DWC3 USB node

 arch/arm64/boot/dts/qcom/sc7180.dtsi |   1 +
 drivers/usb/dwc3/dwc3-qcom.c         | 127 ++++++++++++++++++++++++++++++++++-
 2 files changed, 126 insertions(+), 2 deletions(-)
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#3 lore raw

PATCH v9 2/2 arm64: dts: qcom: sc7180: Add maximum speed property for DWC3 USB node

Adding maximum speed property for DWC3 USB node which can be used for setting interconnect bandwidth.

---
 arch/arm64/boot/dts/qcom/sc7180.dtsi | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/qcom/sc7180.dtsi +1 -0
index 16df08d..3fe759b6 100644
@@ -2656,6 +2656,7 @@
 				snps,dis_enblslpm_quirk;
 				phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
 				phy-names = "usb2-phy", "usb3-phy";
+				maximum-speed = "super-speed";
 			};
 		};
 
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#2 lore raw

Re: [PATCH v9 1/2] usb: dwc3: qcom: Add interconnect support in dwc3 driver

In reply to Sandeep Maheswaram

Hi Sandeep,

Quoted 9 lines · Sandeep Maheswaram

Add interconnect support in dwc3-qcom driver to vote for bus bandwidth.

This requires for two different paths - from USB to DDR. The other is from APPS to USB.

^
Please remove this tag for now (should have requested this earlier). It seems we are very close, but apparently the review is still/again ongoing.

Quoted 41 lines
---
 drivers/usb/dwc3/dwc3-qcom.c | 127 ++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 125 insertions(+), 2 deletions(-)
drivers/usb/dwc3/dwc3-qcom.c +11 -0
index e1e78e9..82e08ff 100644
@@ -13,6 +13,7 @@
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/extcon.h>
+#include <linux/interconnect.h>
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
 #include <linux/phy/phy.h>
@@ -43,6 +44,14 @@
 #define SDM845_QSCRATCH_SIZE			0x400
 #define SDM845_DWC3_CORE_SIZE			0xcd00
 
+/* Interconnect path bandwidths in MBps */
+#define USB_MEMORY_AVG_HS_BW MBps_to_icc(240)
+#define USB_MEMORY_PEAK_HS_BW MBps_to_icc(700)
+#define USB_MEMORY_AVG_SS_BW  MBps_to_icc(1000)
+#define USB_MEMORY_PEAK_SS_BW MBps_to_icc(2500)
+#define APPS_USB_AVG_BW 0
+#define APPS_USB_PEAK_BW MBps_to_icc(40)
+
 struct dwc3_acpi_pdata {
 	u32			qscratch_base_offset;
 	u32			qscratch_base_size;
@@ -76,6 +85,8 @@ struct dwc3_qcom {
 	enum usb_dr_mode	mode;
 	bool			is_suspended;
 	bool			pm_suspended;
+	struct icc_path		*icc_path_ddr;
+	struct icc_path		*icc_path_apps;
 };
 
 static inline void dwc3_qcom_setbits(void __iomem *base, u32 offset, u32 val)

drivers/usb/dwc3/dwc3-qcom.c static int dwc3_qcom_register_extcon(struct dwc3_qcom *qcom) · line 206

Quoted 6 lines
drivers/usb/dwc3/dwc3-qcom.c +3 -0
@@ -190,6 +201,101 @@ static int dwc3_qcom_register_extcon(struct dwc3_qcom *qcom)
 	return 0;
 }
 
+/* Bandwidth levels are set in dwc3_qcom_interconnect_init ,
+ * so just "enable" interconnects.
+ */

nits:
- the common format for functions in this file is:

    /**
     * <description>
     */

- remove blank before the ','

That said, not all functions in this file have documentation, and this comment doesn't seem to add much, so you could consider to just remove it.

drivers/usb/dwc3/dwc3-qcom.c static int dwc3_qcom_register_extcon(struct dwc3_qcom *qcom) · line 217

Quoted 11 lines
drivers/usb/dwc3/dwc3-qcom.c +11 -0
+static int dwc3_qcom_interconnect_enable(struct dwc3_qcom *qcom)
+{
+	int ret;
+
+	ret = icc_enable(qcom->icc_path_ddr);
+	if (ret)
+		return ret;
+
+	ret = icc_enable(qcom->icc_path_apps);
+	if (ret)
+		return ret;

You changed the logic here: in v8 the DDR path would be disabled again if enabling the APPS patch failed. I think it would be preferable to keep the enable state of the two ICC paths in sync if possible.

If not, just do

   	return icc_enable(qcom->icc_path_apps);

instead of

	if (ret)
		return ret;

	return ret;

drivers/usb/dwc3/dwc3-qcom.c static int dwc3_qcom_register_extcon(struct dwc3_qcom *qcom) · line 222

Quoted 5 lines
drivers/usb/dwc3/dwc3-qcom.c +5 -0
+
+	return ret;
+}
+
+/*Disabling the interconnect, will set the bandwidth to 0 */

nit: add blank before 'Disabling'.

Same as above, the comment doesn't add much value, you can consider to remove it.

drivers/usb/dwc3/dwc3-qcom.c static int dwc3_qcom_register_extcon(struct dwc3_qcom *qcom) · line 233

Quoted 11 lines
drivers/usb/dwc3/dwc3-qcom.c +11 -0
+static int dwc3_qcom_interconnect_disable(struct dwc3_qcom *qcom)
+{
+	int ret;
+
+	ret = icc_disable(qcom->icc_path_ddr);
+	if (ret)
+		return ret;
+
+	ret = icc_disable(qcom->icc_path_apps);
+	if (ret)
+		return ret;

Same as above, either reenable the DDR path in case of failure, or simplify the code.

Quoted 100 lines
drivers/usb/dwc3/dwc3-qcom.c +74 -1
+
+	return ret;
+}
+
+/**
+ * dwc3_qcom_interconnect_init() - Get interconnect path handles
+ * and set bandwidhth.
+ * @qcom:			Pointer to the concerned usb core.
+ *
+ */
+static int dwc3_qcom_interconnect_init(struct dwc3_qcom *qcom)
+{
+	struct device *dev = qcom->dev;
+	int ret;
+
+	qcom->icc_path_ddr = of_icc_get(dev, "usb-ddr");
+	if (IS_ERR(qcom->icc_path_ddr)) {
+		dev_err(dev, "failed to get usb-ddr path: %ld\n",
+			PTR_ERR(qcom->icc_path_ddr));
+		return PTR_ERR(qcom->icc_path_ddr);
+	}
+
+	qcom->icc_path_apps = of_icc_get(dev, "apps-usb");
+	if (IS_ERR(qcom->icc_path_apps)) {
+		dev_err(dev, "failed to get apps-usb path: %ld\n",
+				PTR_ERR(qcom->icc_path_apps));
+		return PTR_ERR(qcom->icc_path_apps);
+	}
+
+	if (usb_get_maximum_speed(&qcom->dwc3->dev) >= USB_SPEED_SUPER ||
+			usb_get_maximum_speed(&qcom->dwc3->dev) == USB_SPEED_UNKNOWN)
+		ret = icc_set_bw(qcom->icc_path_ddr,
+			USB_MEMORY_AVG_SS_BW, USB_MEMORY_PEAK_SS_BW);
+	else
+		ret = icc_set_bw(qcom->icc_path_ddr,
+			USB_MEMORY_AVG_HS_BW, USB_MEMORY_PEAK_HS_BW);
+
+	if (ret) {
+		dev_err(dev, "failed to set bandwidth for usb-ddr path: %d\n", ret);
+		return ret;
+	}
+
+	ret = icc_set_bw(qcom->icc_path_apps,
+		APPS_USB_AVG_BW, APPS_USB_PEAK_BW);
+
+	if (ret) {
+		dev_err(dev, "failed to set bandwidth for apps-usb path: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * dwc3_qcom_interconnect_exit() - Release interconnect path handles
+ * @qcom:			Pointer to the concerned usb core.
+ *
+ * This function is used to release interconnect path handle.
+ */
+static void dwc3_qcom_interconnect_exit(struct dwc3_qcom *qcom)
+{
+	icc_put(qcom->icc_path_ddr);
+	icc_put(qcom->icc_path_apps);
+}
+
 static void dwc3_qcom_disable_interrupts(struct dwc3_qcom *qcom)
 {
 	if (qcom->hs_phy_irq) {
@@ -239,7 +345,7 @@ static void dwc3_qcom_enable_interrupts(struct dwc3_qcom *qcom)
 static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
 {
 	u32 val;
-	int i;
+	int i, ret;
 
 	if (qcom->is_suspended)
 		return 0;
@@ -251,6 +357,10 @@ static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
 	for (i = qcom->num_clocks - 1; i >= 0; i--)
 		clk_disable_unprepare(qcom->clks[i]);
 
+	ret = dwc3_qcom_interconnect_disable(qcom);
+	if (ret)
+		dev_warn(qcom->dev, "failed to disable interconnect: %d\n", ret);
+
 	qcom->is_suspended = true;
 	dwc3_qcom_enable_interrupts(qcom);
 
@@ -276,6 +386,10 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom)
 		}
 	}
 
+	ret = dwc3_qcom_interconnect_enable(qcom);
+	if (ret)
+		dev_warn(qcom->dev, "failed to enable interconnect: %d\n", ret);
+
 	/* Clear existing events from PHY related to L2 in/out */
 	dwc3_qcom_setbits(qcom->qscratch_base, PWR_EVNT_IRQ_STAT_REG,
 			  PWR_EVNT_LPM_IN_L2_MASK | PWR_EVNT_LPM_OUT_L2_MASK);

drivers/usb/dwc3/dwc3-qcom.c static int dwc3_qcom_resume(struct dwc3_qcom *qcom) · line 403

Quoted 5 lines
drivers/usb/dwc3/dwc3-qcom.c +2 -0
@@ -285,6 +399,8 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom)
 	return 0;
 }
 
+
+

nit: remove one empty line

Quoted 44 lines
drivers/usb/dwc3/dwc3-qcom.c +8 -1
 static irqreturn_t qcom_dwc3_resume_irq(int irq, void *data)
 {
 	struct dwc3_qcom *qcom = data;
@@ -638,6 +754,10 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 		goto depopulate;
 	}
 
+	ret = dwc3_qcom_interconnect_init(qcom);
+	if (ret)
+		goto depopulate;
+
 	qcom->mode = usb_get_dr_mode(&qcom->dwc3->dev);
 
 	/* enable vbus override for device mode */
@@ -647,7 +767,7 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 	/* register extcon to override sw_vbus on Vbus change later */
 	ret = dwc3_qcom_register_extcon(qcom);
 	if (ret)
-		goto depopulate;
+		goto interconnect_exit;
 
 	device_init_wakeup(&pdev->dev, 1);
 	qcom->is_suspended = false;
@@ -657,6 +777,8 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 
 	return 0;
 
+interconnect_exit:
+	dwc3_qcom_interconnect_exit(qcom);
 depopulate:
 	if (np)
 		of_platform_depopulate(&pdev->dev);
@@ -687,6 +809,7 @@ static int dwc3_qcom_remove(struct platform_device *pdev)
 	}
 	qcom->num_clocks = 0;
 
+	dwc3_qcom_interconnect_exit(qcom);
 	reset_control_assert(qcom->resets);
 
 	pm_runtime_allow(dev);
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation