i2c: iproc: fix race between client unreg and isr
Subsystems (2)
PATCH v2 1/1 i2c: iproc: fix race between client unreg and isr
When i2c client unregisters, synchronize irq before setting iproc_i2c->slave to NULL.
(1) disable_irq()
(2) Mask event enable bits in control reg
(3) Erase slave address (avoid further writes to rx fifo)
(4) Flush tx and rx FIFOs
(5) Clear pending event (interrupt) bits in status reg
(6) enable_irq()
(7) Set client pointer to NULL
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000318
[ 371.020421] pc : bcm_iproc_i2c_isr+0x530/0x11f0 [ 371.025098] lr : __handle_irq_event_percpu+0x6c/0x170 [ 371.030309] sp : ffff800010003e40 [ 371.033727] x29: ffff800010003e40 x28: 0000000000000060 [ 371.039206] x27: ffff800010ca9de0 x26: ffff800010f895df [ 371.044686] x25: ffff800010f18888 x24: ffff0008f7ff3600 [ 371.050165] x23: 0000000000000003 x22: 0000000001600000 [ 371.055645] x21: ffff800010f18888 x20: 0000000001600000 [ 371.061124] x19: ffff0008f726f080 x18: 0000000000000000 [ 371.066603] x17: 0000000000000000 x16: 0000000000000000 [ 371.072082] x15: 0000000000000000 x14: 0000000000000000 [ 371.077561] x13: 0000000000000000 x12: 0000000000000001 [ 371.083040] x11: 0000000000000000 x10: 0000000000000040 [ 371.088519] x9 : ffff800010f317c8 x8 : ffff800010f317c0 [ 371.093999] x7 : ffff0008f805b3b0 x6 : 0000000000000000 [ 371.099478] x5 : ffff0008f7ff36a4 x4 : ffff8008ee43d000 [ 371.104957] x3 : 0000000000000000 x2 : ffff8000107d64c0 [ 371.110436] x1 : 00000000c00000af x0 : 0000000000000000
[ 371.115916] Call trace: [ 371.118439] bcm_iproc_i2c_isr+0x530/0x11f0 [ 371.122754] __handle_irq_event_percpu+0x6c/0x170 [ 371.127606] handle_irq_event_percpu+0x34/0x88 [ 371.132189] handle_irq_event+0x40/0x120 [ 371.136234] handle_fasteoi_irq+0xcc/0x1a0 [ 371.140459] generic_handle_irq+0x24/0x38 [ 371.144594] __handle_domain_irq+0x60/0xb8 [ 371.148820] gic_handle_irq+0xc0/0x158 [ 371.152687] el1_irq+0xb8/0x140 [ 371.155927] arch_cpu_idle+0x10/0x18 [ 371.159615] do_idle+0x204/0x290 [ 371.162943] cpu_startup_entry+0x24/0x60 [ 371.166990] rest_init+0xb0/0xbc [ 371.170322] arch_call_rest_init+0xc/0x14 [ 371.174458] start_kernel+0x404/0x430
--- drivers/i2c/busses/i2c-bcm-iproc.c | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-)
drivers/i2c/busses/i2c-bcm-iproc.c +12 -1
@@ -1078,7 +1078,7 @@ static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave)if (!iproc_i2c->slave)return -EINVAL ; - iproc_i2c->slave =NULL ; +disable_irq (iproc_i2c->irq);/* disable all slave interrupts */ tmp =iproc_i2c_rd_reg (iproc_i2c,IE_OFFSET );
@@ -1091,6 +1091,17 @@ static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave) tmp &= ~BIT (S_CFG_EN_NIC_SMB_ADDR3_SHIFT );iproc_i2c_wr_reg (iproc_i2c,S_CFG_SMBUS_ADDR_OFFSET , tmp); +/* flush TX/RX FIFOs */ + tmp = (BIT (S_FIFO_RX_FLUSH_SHIFT ) |BIT (S_FIFO_TX_FLUSH_SHIFT )); +iproc_i2c_wr_reg (iproc_i2c,S_FIFO_CTRL_OFFSET , tmp); + +/* clear all pending slave interrupts */ +iproc_i2c_wr_reg (iproc_i2c,IS_OFFSET ,ISR_MASK_SLAVE ); + +enable_irq (iproc_i2c->irq); + + iproc_i2c->slave =NULL ; +return 0 ; }
Signature · 1 line
2.17.1
Quoted 73 lines · Dhananjay Phadke
When i2c client unregisters, synchronize irq before setting
iproc_i2c->slaveto NULL.(1)
disable_irq()
(2) Mask event enable bits in control reg
(3) Erase slave address (avoid further writes to rx fifo)
(4) Flush tx and rx FIFOs
(5) Clear pending event (interrupt) bits in status reg
(6)enable_irq()
(7) Set client pointer to NULLUnable to handle kernel NULL pointer dereference at virtual address 0000000000000318[ 371.020421] pc : bcm_iproc_i2c_isr+0x530/0x11f0 [ 371.025098] lr : __handle_irq_event_percpu+0x6c/0x170 [ 371.030309] sp : ffff800010003e40 [ 371.033727] x29: ffff800010003e40 x28: 0000000000000060 [ 371.039206] x27: ffff800010ca9de0 x26: ffff800010f895df [ 371.044686] x25: ffff800010f18888 x24: ffff0008f7ff3600 [ 371.050165] x23: 0000000000000003 x22: 0000000001600000 [ 371.055645] x21: ffff800010f18888 x20: 0000000001600000 [ 371.061124] x19: ffff0008f726f080 x18: 0000000000000000 [ 371.066603] x17: 0000000000000000 x16: 0000000000000000 [ 371.072082] x15: 0000000000000000 x14: 0000000000000000 [ 371.077561] x13: 0000000000000000 x12: 0000000000000001 [ 371.083040] x11: 0000000000000000 x10: 0000000000000040 [ 371.088519] x9 : ffff800010f317c8 x8 : ffff800010f317c0 [ 371.093999] x7 : ffff0008f805b3b0 x6 : 0000000000000000 [ 371.099478] x5 : ffff0008f7ff36a4 x4 : ffff8008ee43d000 [ 371.104957] x3 : 0000000000000000 x2 : ffff8000107d64c0 [ 371.110436] x1 : 00000000c00000af x0 : 0000000000000000[ 371.115916] Call trace: [ 371.118439] bcm_iproc_i2c_isr+0x530/0x11f0 [ 371.122754] __handle_irq_event_percpu+0x6c/0x170 [ 371.127606] handle_irq_event_percpu+0x34/0x88 [ 371.132189] handle_irq_event+0x40/0x120 [ 371.136234] handle_fasteoi_irq+0xcc/0x1a0 [ 371.140459] generic_handle_irq+0x24/0x38 [ 371.144594] __handle_domain_irq+0x60/0xb8 [ 371.148820] gic_handle_irq+0xc0/0x158 [ 371.152687] el1_irq+0xb8/0x140 [ 371.155927] arch_cpu_idle+0x10/0x18 [ 371.159615] do_idle+0x204/0x290 [ 371.162943] cpu_startup_entry+0x24/0x60 [ 371.166990] rest_init+0xb0/0xbc [ 371.170322] arch_call_rest_init+0xc/0x14 [ 371.174458] start_kernel+0x404/0x430Fixes c245d94ed106 ("i2c: iproc: Add multi byte read-write support for slave mode")Signed-off-by Dhananjay Phadke <[email protected]>--- drivers/i2c/busses/i2c-bcm-iproc.c | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-)drivers/i2c/busses/i2c-bcm-iproc.c +1
-1@@ -1078,7 +1078,7 @@ static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave)if (!iproc_i2c->slave)return -EINVAL ; - iproc_i2c->slave =NULL ; +disable_irq (iproc_i2c->irq);/* disable all slave interrupts */ tmp =iproc_i2c_rd_reg (iproc_i2c,IE_OFFSET );@@ -1091,6 +1091,17 @@ static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave) tmp &= ~BIT (S_CFG_EN_NIC_SMB_ADDR3_SHIFT );iproc_i2c_wr_reg (iproc_i2c,S_CFG_SMBUS_ADDR_OFFSET , tmp);
drivers/i2c/busses/i2c-bcm-iproc.c static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave) · line 1103
Quoted 10 lines
drivers/i2c/busses/i2c-bcm-iproc.c +10
-0+/* flush TX/RX FIFOs */ + tmp = (BIT (S_FIFO_RX_FLUSH_SHIFT ) |BIT (S_FIFO_TX_FLUSH_SHIFT )); +iproc_i2c_wr_reg (iproc_i2c,S_FIFO_CTRL_OFFSET , tmp); + +/* clear all pending slave interrupts */ +iproc_i2c_wr_reg (iproc_i2c,IS_OFFSET ,ISR_MASK_SLAVE ); + +enable_irq (iproc_i2c->irq); + + iproc_i2c->slave =NULL ;
There is nothing that checks on iproc_i2c->slave being valid within the interrupt handler, we assume that the pointer is valid which is fin, however non functional it may be, it may feel more natural to move the assignment before the enable_irq()?
Signature · 1 line
Florian
Quoted 16 lines · Florian Fainelli
Quoted 16 lines
When i2c client unregisters, synchronize irq before setting
iproc_i2c->slaveto NULL.(1)
disable_irq()
(2) Mask event enable bits in control reg
(3) Erase slave address (avoid further writes to rx fifo)
(4) Flush tx and rx FIFOs
(5) Clear pending event (interrupt) bits in status reg
(6)enable_irq()
(7) Set client pointer to NULLdrivers/i2c/busses/i2c-bcm-iproc.c +0
-0@@ -1091,6 +1091,17 @@ static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave) tmp &= ~BIT (S_CFG_EN_NIC_SMB_ADDR3_SHIFT );iproc_i2c_wr_reg (iproc_i2c,S_CFG_SMBUS_ADDR_OFFSET , tmp);
Quoted 15 lines
drivers/i2c/busses/i2c-bcm-iproc.c static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave) · line 1103
Quoted 10 lines
drivers/i2c/busses/i2c-bcm-iproc.c +10
-0+/* flush TX/RX FIFOs */ + tmp = (BIT (S_FIFO_RX_FLUSH_SHIFT ) |BIT (S_FIFO_TX_FLUSH_SHIFT )); +iproc_i2c_wr_reg (iproc_i2c,S_FIFO_CTRL_OFFSET , tmp); + +/* clear all pending slave interrupts */ +iproc_i2c_wr_reg (iproc_i2c,IS_OFFSET ,ISR_MASK_SLAVE ); + +enable_irq (iproc_i2c->irq); + + iproc_i2c->slave =NULL ;There is nothing that checks on
iproc_i2c->slavebeing valid within the interrupt handler, we assume that the pointer is valid which is fin, however non functional it may be, it may feel more natural to move the assignment before theenable_irq()?
As far as the teardown sequence ensures no more interrupts arrive after enable_irq() and they are enabled only after setting pointer during client register(); checking for NULL in ISR isn't necessary.
If The teardown sequence doesn't guarantee quiescing of interrupts, setting NULL before or after enable_irq() is equally vulnerable.
Dhananjay
Quoted 33 lines · Dhananjay Phadke
Quoted 16 lines · Florian Fainelli
Quoted 16 lines
When i2c client unregisters, synchronize irq before setting
iproc_i2c->slaveto NULL.(1)
disable_irq()
(2) Mask event enable bits in control reg
(3) Erase slave address (avoid further writes to rx fifo)
(4) Flush tx and rx FIFOs
(5) Clear pending event (interrupt) bits in status reg
(6)enable_irq()
(7) Set client pointer to NULLdrivers/i2c/busses/i2c-bcm-iproc.c +0
-0@@ -1091,6 +1091,17 @@ static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave) tmp &= ~BIT (S_CFG_EN_NIC_SMB_ADDR3_SHIFT );iproc_i2c_wr_reg (iproc_i2c,S_CFG_SMBUS_ADDR_OFFSET , tmp);Quoted 15 lines
drivers/i2c/busses/i2c-bcm-iproc.c static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave) · line 1103
Quoted 10 lines
drivers/i2c/busses/i2c-bcm-iproc.c +10
-0+/* flush TX/RX FIFOs */ + tmp = (BIT (S_FIFO_RX_FLUSH_SHIFT ) |BIT (S_FIFO_TX_FLUSH_SHIFT )); +iproc_i2c_wr_reg (iproc_i2c,S_FIFO_CTRL_OFFSET , tmp); + +/* clear all pending slave interrupts */ +iproc_i2c_wr_reg (iproc_i2c,IS_OFFSET ,ISR_MASK_SLAVE ); + +enable_irq (iproc_i2c->irq); + + iproc_i2c->slave =NULL ;There is nothing that checks on
iproc_i2c->slavebeing valid within the interrupt handler, we assume that the pointer is valid which is fin, however non functional it may be, it may feel more natural to move the assignment before theenable_irq()?
Quoted 3 lines
As far as the teardown sequence ensures no more interrupts arrive after
enable_irq()and they are enabled only after setting pointer during clientregister(); checking for NULL in ISR isn't necessary.
Agreed.
Quoted 3 lines
If The teardown sequence doesn't guarantee quiescing of interrupts, setting NULL before or after
enable_irq()is equally vulnerable.
The teardown sequence is sort of a critical section if we may say, so ensuring that everything happens within it and that enable_irq() is the last operation would seem more natural to me at least. Thanks
Signature · 1 line
Florian
Quoted 36 lines · Florian Fainelli
Quoted 33 lines · Dhananjay Phadke
Quoted 31 lines · Florian Fainelli
Quoted 16 lines
When i2c client unregisters, synchronize irq before setting
iproc_i2c->slaveto NULL.(1)
disable_irq()
(2) Mask event enable bits in control reg
(3) Erase slave address (avoid further writes to rx fifo)
(4) Flush tx and rx FIFOs
(5) Clear pending event (interrupt) bits in status reg
(6)enable_irq()
(7) Set client pointer to NULLdrivers/i2c/busses/i2c-bcm-iproc.c +0
-0@@ -1091,6 +1091,17 @@ static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave) tmp &= ~BIT (S_CFG_EN_NIC_SMB_ADDR3_SHIFT );iproc_i2c_wr_reg (iproc_i2c,S_CFG_SMBUS_ADDR_OFFSET , tmp);drivers/i2c/busses/i2c-bcm-iproc.c static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave) · line 1103
Quoted 10 lines
drivers/i2c/busses/i2c-bcm-iproc.c +10
-0+/* flush TX/RX FIFOs */ + tmp = (BIT (S_FIFO_RX_FLUSH_SHIFT ) |BIT (S_FIFO_TX_FLUSH_SHIFT )); +iproc_i2c_wr_reg (iproc_i2c,S_FIFO_CTRL_OFFSET , tmp); + +/* clear all pending slave interrupts */ +iproc_i2c_wr_reg (iproc_i2c,IS_OFFSET ,ISR_MASK_SLAVE ); + +enable_irq (iproc_i2c->irq); + + iproc_i2c->slave =NULL ;There is nothing that checks on
iproc_i2c->slavebeing valid within the interrupt handler, we assume that the pointer is valid which is fin, however non functional it may be, it may feel more natural to move the assignment before theenable_irq()?
Quoted 6 lines
Quoted 3 lines
As far as the teardown sequence ensures no more interrupts arrive after
enable_irq()and they are enabled only after setting pointer during clientregister(); checking for NULL in ISR isn't necessary.Agreed.
Okay I think we all agree that this teardown sequence will guarantee that no further "slave" interrupts will be fired after it.
Quoted 8 lines
Quoted 3 lines
If The teardown sequence doesn't guarantee quiescing of interrupts, setting NULL before or after
enable_irq()is equally vulnerable.The teardown sequence is sort of a critical section if we may say, so ensuring that everything happens within it and that
enable_irq()is the last operation would seem more natural to me at least. Thanks
I tend to agree with Florian here.
1. Enable/Disable IRQ is done on the interrupt line for both master and slave (or even other peripherals that share the same interrupt line, although that is not the case here since this interrupt is dedicated to I2C in all iProc based SoCs).
2. The tear down sequence here wrapped by disable/enable_irq is slave specific
The effect of 1. is temporary, and the purpose of it is to ensure slave interrupts are quiesced properly at the end of the sequence.
If we consider both 1. and 2., I agree with Florian that while the end result is the same, it is indeed more natural to wrap the entire slave tear down sequence within disable/enable irq.
Thanks,
Ray