DMA Timeouts with 3112 SATA Controller (status == 0x21)
Hi,
I am in the process of trying to setup a Dual Xeon machine with a Silicon Image 3112 SATA controller. The system is booting from a parallel ATA disk and there are two SATA disks being used to store data.
I was able to access the SATA drives, both in a raid0 and non-raid configuration, using the driver (sii3112rl.o) with the machine. This module was compiled for a uni-processor RH8.0 kernel (2.8.18-14). We were getting transfer rates of around 40MB/s in non-raid and 80MB/s in raid0. There was no SMP version of the module supplied so it was kind of useless to us.
So, I tried a 2.4.21-pre6 kernel (SMP with hyperthreading). The 3112 controller was identified at boot and I was able to access the disks. However, hdparm was reporting very poor transfer rates, around 1.8MB/s. It turned out that DMA was not enabled on the disks. When I enabled DMA I got back to a transfer rate around 40MB/s. I set the transfer mode to udma6.
Then I tried to make an ext3 filesystem. mkfs would get up to around the 240th inode table (ie: "Writing inode tables: 240/xyz") and then freeze up for a while. The following errors were displayed on the console:
hde: dma_timer_expiry: dma_status == 0x21
hde: timeout waiting for DMA
hde: timeout waiting for DMA
hde: status timeout: status = 0xd8 {Busy}
hde: drive not ready for command
ide2: reset phy status=0x00000113 siimage_reset
ide2: reset timed-out, status=0xd8
hde: status timeout: status = 0xd8 {Busy}
hde: drive not ready for command
ide2: reset phy status=0x00000113 siimage_reset
ide2: reset timed-out, status=0xd8followed by loads of IO errors. After this, the disk was uncontactable. I thought the problem might be with udma6 so I tried all of them but with the same problems. I also tried 2.5.66 and a RedHat 2.4.20-2.54 kernel but these had the same problems. If I turned DMA off I was able to make a filesystem (although very slowly). I was also able to make a filesystem using the original supplied driver.
The timeouts also occurred if I used the silraid module and accessed the disks via /dev/ataraid/d0.
I could swap the drives for parallel ATA ones but would rather get the SATA ones working if possible. I recall reading a message from Andre containing performance details about a 3112 controller and Linux raid 1, so I presume that it is possible to get this configuration going and it is just that I am a doofus.
Here is some info on the machine:
# lspci 00:00.0 Host bridge: Intel Corp.: Unknown device 2550 (rev 03) 00:00.1 Class ff00: Intel Corp.: Unknown device 2551 (rev 03) 00:01.0 PCI bridge: Intel Corp.: Unknown device 2552 (rev 03) 00:02.0 PCI bridge: Intel Corp.: Unknown device 2553 (rev 03) 00:02.1 Class ff00: Intel Corp.: Unknown device 2554 (rev 03) 00:1d.0 USB Controller: Intel Corp. 82801DB USB (Hub #1) (rev 02) 00:1d.1 USB Controller: Intel Corp. 82801DB USB (Hub #2) (rev 02) 00:1d.2 USB Controller: Intel Corp. 82801DB USB (Hub #3) (rev 02) 00:1d.7 USB Controller: Intel Corp. 82801DB USB EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB PCI Bridge (rev 82) 00:1f.0 ISA bridge: Intel Corp. 82801DB ISA Bridge (LPC) (rev 02) 00:1f.1 IDE interface: Intel Corp. 82801DB ICH4 IDE (rev 02) 00:1f.3 SMBus: Intel Corp. 82801DB SMBus (rev 02) 02:1c.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04) 02:1d.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04) 02:1e.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04) 02:1f.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04) 04:02.0 Ethernet controller: Intel Corp. 82540EM Gigabit Ethernet Controller (rev 02) 05:02.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) 05:03.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 0d) 05:04.0 Unknown mass storage controller: CMD Technology Inc: Unknown device 3112 (rev 02)
# hdparm -i /dev/hde
/dev/hde:
Model=ST3120023AS, FwRev=3.01, SerialNo=3KA1MN43
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=234441648
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2: 1 2 3 4 5 6# hdparm -I /dev/hde
/dev/hde:
ATA device, with non-removable media
Model Number: ST3120023AS
Serial Number: 3KA1MN43
Firmware Revision: 3.01
Standards:
Used: ATA/ATAPI-6 T13 1410D revision 2
Supported: 6 5 4 3
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 234441648
device size with M = 1024*1024: 114473 MBytes
device size with M = 1000*1000: 120034 MBytes (120 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 4 Queue depth: 1
Standby timer values: spec'd by Standard
R/W multiple sector transfer: Max = 16 Current = 16
Recommended acoustic management value: 128, current value: 0
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
Automatic Acoustic Management feature set
SET MAX security extension
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
HW reset results:
CBLID- above Vih
Device num = 0
Checksum: correct# smartctl -v /dev/hde Vendor Specific SMART Attributes with Thresholds: Revision Number: 10 Attribute Flag Value Worst Threshold Raw Value ( 1)Raw Read Error Rate 0x000f 066 060 034 0000083fe871 ( 3)Spin Up Time 0x0003 100 100 000 000000000000 ( 4)Start Stop Count 0x0032 100 100 020 000000000000 ( 5)Reallocated Sector Ct 0x0033 100 100 036 000000000000 ( 7)Seek Error Rate 0x000f 070 060 030 000000a93dad ( 9)Power On Hours 0x0032 100 100 000 0000000000ed ( 10)Spin Retry Count 0x0013 100 100 097 000000000000 ( 12)Power Cycle Count 0x0032 100 100 020 000000000047 (194)Unknown Attribute 0x0022 036 051 000 000000000024 (195)Unknown Attribute 0x001a 066 060 000 0000083fe871 (197)Current Pending Sector 0x0012 100 100 000 000000000000 (198)Offline Uncorrectable 0x0010 100 100 000 000000000000 (199)UDMA CRC Error Count 0x003e 200 200 000 000000000000 (200)Unknown Attribute 0x0000 100 253 000 000000000000 (202)Unknown Attribute 0x0032 100 253 000 000000000000
Any help would be most appreciated.
Thanks
David
Signature · 4 lines
David Tymon Senior Software Engineer mailto:[email protected] Safehouse International http://www.safehouse.com.au Tel: +61 3 9827 5411 Fax: +61 3 9827 7411
Hi *,
On Saturday I tried a Seagate 120GiB SATA with my onboard SiI3112 on my ASUS P4G8X (with an Intel 7205 chipset). I suppose that David is using a similiar setup with an 7505 chipset? Perhaps the problem is somehow related to this chipset: I saw the exact same errors as David. I also tried several kernels: 2.4.20-ac2, 2.4.20-pre5-ac3, 2.4.20-pre7, 2.5.66, 2.4.20-8 from Redhat 9, ... with exactly the same result.
Martin