Skip to contentSkip to conversation

iw: add optional argument to parse 6G band channel

PATCH In review Pradeep Kumar Chitrapu 3 participants 8 messages Oct 9, 2020 – Nov 6, 2020

lore
Share & tools
lore
#1 lore raw

PATCH 1/1 iw: enable 80MHz support for 6GHz band 11s mesh

In reply to Pradeep Kumar Chitrapu

without this 11s mesh could not be configured with bandwidth 80MHz in 6G band using iw. Also, this will be required to set frequency for 6GHz band in 80MHz.

example:
iw <interface> mesh join <meshname> freq 6195 80MHz

---
 util.c | 13 ++++++++-----
 1 file changed, 8 insertions(+), 5 deletions(-)
util.c +8 -5
index 9ca32c5295ae..175470f11a27 100644
@@ -1241,21 +1241,24 @@ void iw_hexdump(const char *prefix, const __u8 *buf, size_t size)
 int get_cf1(const struct chanmode *chanmode, unsigned long freq)
 {
 	unsigned int cf1 = freq, j;
-	unsigned int vht80[] = { 5180, 5260, 5500, 5580, 5660, 5745 };
+	unsigned int bw80[] = { 5180, 5260, 5500, 5580, 5660, 5745,
+				5955, 6035, 6115, 6195, 6275, 6355,
+				6435, 6515, 6595, 6675, 6755, 6835,
+				6195, 6995 };
 	unsigned int vht160[] = { 5180, 5500 };
 
 	switch (chanmode->width) {
 	case NL80211_CHAN_WIDTH_80:
 	        /* setup center_freq1 */
-		for (j = 0; j < ARRAY_SIZE(vht80); j++) {
-			if (freq >= vht80[j] && freq < vht80[j] + 80)
+		for (j = 0; j < ARRAY_SIZE(bw80); j++) {
+			if (freq >= bw80[j] && freq < bw80[j] + 80)
 				break;
 		}
 
-		if (j == ARRAY_SIZE(vht80))
+		if (j == ARRAY_SIZE(bw80))
 			break;
 
-		cf1 = vht80[j] + 30;
+		cf1 = bw80[j] + 30;
 		break;
 	case NL80211_CHAN_WIDTH_160:
 		/* setup center_freq1 */
Signature · 1 line
1.9.1
#0 lore raw

PATCH 1/1 iw: add optional argument to parse 6G band channel

Channel numbers of 6G band overlaps with those of 2G or 5G bands. Therefore, an optional argument "6G" is added and expected next to channel number to map it to correct 6GHz frequency. If not specified, defaults to matching 2G or 5G frequency.

example:
iw wlanX set channel 149 6G 80MHz --> maps to 6695 MHz
iw wlanX set channel 149 80MHz --> maps to 5745 MHz

---
 interface.c |  5 +++--
 phy.c       |  8 ++++----
 util.c      | 13 +++++++++----
 3 files changed, 16 insertions(+), 10 deletions(-)
interface.c +3 -2
index 89c95a9ac4ab..8e85f831f9f9 100644
@@ -725,8 +725,9 @@ COMMAND(switch, freq,
 	"<control freq> [5|10|20|40|80|80+80|160] [<center1_freq> [<center2_freq>]] [beacons <count>] [block-tx]",
 	NL80211_CMD_CHANNEL_SWITCH, 0, CIB_NETDEV, handle_freq,
 	"Switch the operating channel by sending a channel switch announcement (CSA).");
-COMMAND(switch, channel, "<channel> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz] [beacons <count>] [block-tx]",
-	NL80211_CMD_CHANNEL_SWITCH, 0, CIB_NETDEV, handle_chan, NULL);
+COMMAND(switch, channel, "<channel> [6G] [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz] [beacons <count>] [block-tx]",
+	NL80211_CMD_CHANNEL_SWITCH, 0, CIB_NETDEV, handle_chan,
+	"6GHz channels expects '6G' in argument. If not specified, defaults to 5GHz or 2GHz channels");
 
 
 static int toggle_tid_param(const char *argv0, const char *argv1,
phy.c +4 -4
index 2d489efd7690..31d96cec7886 100644
@@ -222,9 +222,9 @@ static int handle_chan(struct nl80211_state *state, struct nl_msg *msg,
 
 	return put_chandef(msg, &chandef);
 }
-COMMAND(set, channel, "<channel> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz|160MHz]",
+COMMAND(set, channel, "<channel> [6G] [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz|160MHz]",
 	NL80211_CMD_SET_WIPHY, 0, CIB_PHY, handle_chan, NULL);
-COMMAND(set, channel, "<channel> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz|160MHz]",
+COMMAND(set, channel, "<channel> [6G] [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz|160MHz]",
 	NL80211_CMD_SET_WIPHY, 0, CIB_NETDEV, handle_chan, NULL);
 
 
@@ -369,12 +369,12 @@ err_out:
 		free(cac_trigger_argv);
 	return err;
 }
-TOPLEVEL(cac, "channel <channel> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz]\n"
+TOPLEVEL(cac, "channel <channel> [6G] [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz]\n"
 	      "freq <freq> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz]\n"
 	      "freq <control freq> [5|10|20|40|80|80+80|160] [<center1_freq> [<center2_freq>]]",
 	 0, 0, CIB_NETDEV, handle_cac, NULL);
 COMMAND(cac, trigger,
-	"channel <channel> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz]\n"
+	"channel <channel> [6G] [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz]\n"
 	"freq <frequency> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz]\n"
 	"freq <frequency> [5|10|20|40|80|80+80|160] [<center1_freq> [<center2_freq>]]",
 	NL80211_CMD_RADAR_DETECT, 0, CIB_NETDEV, handle_cac_trigger,
util.c +9 -4
index 0a9083c613a4..9ca32c5295ae 100644
@@ -576,7 +576,7 @@ static int parse_freqs(struct chandef *chandef, int argc, char **argv,
  * user by giving "NOHT" instead.
  *
  * The working specifier if chan is set are:
- *   <channel> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz|160MHz]
+ *   <channel> [6G] [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz|160MHz]
  *
  * And if frequency is set:
  *   <freq> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz|160MHz]
@@ -648,7 +648,12 @@ int parse_freqchan(struct chandef *chandef, bool chan, int argc, char **argv,
 	if (chan) {
 		enum nl80211_band band;
 
-		band = freq <= 14 ? NL80211_BAND_2GHZ : NL80211_BAND_5GHZ;
+		if (argc > 1 && strcmp(argv[1], "6G") == 0) {
+			band = NL80211_BAND_6GHZ;
+			_parsed += 1;
+		} else {
+			band = freq <= 14 ? NL80211_BAND_2GHZ : NL80211_BAND_5GHZ;
+		}
 		freq = ieee80211_channel_to_frequency(freq, band);
 	}
 	chandef->control_freq = freq;
@@ -656,9 +661,9 @@ int parse_freqchan(struct chandef *chandef, bool chan, int argc, char **argv,
 	chandef->center_freq1 = freq;
 
 	/* Try to parse HT mode definitions */
-	if (argc > 1) {
+	if ((argc - _parsed) > 0) {
 		for (i = 0; i < ARRAY_SIZE(chanmode); i++) {
-			if (strcasecmp(chanmode[i].name, argv[1]) == 0) {
+			if (strcasecmp(chanmode[i].name, argv[_parsed]) == 0) {
 				chanmode_selected = &chanmode[i];
 				_parsed += 1;
 				break;
Signature · 1 line
1.9.1
#2 lore raw
Quoted 8 lines · Pradeep Kumar Chitrapu

Channel numbers of 6G band overlaps with those of 2G or 5G bands. Therefore, an optional argument "6G" is added and expected next to channel number to map it to correct 6GHz frequency. If not specified, defaults to matching 2G or 5G frequency.

example:
iw wlanX set channel 149 6G 80MHz --> maps to 6695 MHz
iw wlanX set channel 149 80MHz --> maps to 5745 MHz

Hm. I can't really say I like this much.

Is it _really_ needed? I mean, we mostly specify the frequency today, so ... why not just always do that for 6 GHz?

johannes

#3 lore raw
Quoted 6 lines · Johannes Berg
Quoted 5 lines · Pradeep Kumar Chitrapu

Channel numbers of 6G band overlaps with those of 2G or 5G bands. Therefore, an optional argument "6G" is added and expected next to channel number to map it to correct 6GHz frequency. If not specified, defaults to matching 2G or 5G frequency.

Quoted 8 lines
Quoted 3 lines

example:
iw wlanX set channel 149 6G 80MHz --> maps to 6695 MHz
iw wlanX set channel 149 80MHz --> maps to 5745 MHz

Hm. I can't really say I like this much.

Is it _really_ needed? I mean, we mostly specify the frequency today, so ... why not just always do that for 6 GHz?

I suspect there are people preferring channel numbers as much as there are people preferring frequencies. Personally, I think it is acceptable to put this limitation on 6G.

Regards,
Arend

#4 lore raw
Quoted 11 lines · Arend Van Spriel
Quoted 10 lines · Johannes Berg
Quoted 8 lines · Pradeep Kumar Chitrapu

Channel numbers of 6G band overlaps with those of 2G or 5G bands. Therefore, an optional argument "6G" is added and expected next to channel number to map it to correct 6GHz frequency. If not specified, defaults to matching 2G or 5G frequency.

example:
iw wlanX set channel 149 6G 80MHz --> maps to 6695 MHz
iw wlanX set channel 149 80MHz --> maps to 5745 MHz

Quoted 8 lines
Quoted 4 lines

Hm. I can't really say I like this much.

Is it _really_ needed? I mean, we mostly specify the frequency today, so ... why not just always do that for 6 GHz?

I suspect there are people preferring channel numbers as much as there are people preferring frequencies. Personally, I think it is acceptable to put this limitation on 6G.

:)

After I sent the message I figured maybe then we should have different syntax, where we say prefix the channel number by the band?

iw wlanX set channel 6:149 ...
iw wlanX set channel 5:149 ...
iw wlanX set channel 2.4:11 ...

or so?

Seems better than having this optional argument '6G' in one place, and could be supported in a more general fashion.

johannes

#5 lore raw
Quoted 21 lines · Johannes Berg
Quoted 11 lines · Arend Van Spriel
Quoted 10 lines · Johannes Berg
Quoted 8 lines · Pradeep Kumar Chitrapu

Channel numbers of 6G band overlaps with those of 2G or 5G bands. Therefore, an optional argument "6G" is added and expected next to channel number to map it to correct 6GHz frequency. If not specified, defaults to matching 2G or 5G frequency.

example:
iw wlanX set channel 149 6G 80MHz --> maps to 6695 MHz
iw wlanX set channel 149 80MHz --> maps to 5745 MHz

Quoted 8 lines
Quoted 4 lines

Hm. I can't really say I like this much.

Is it _really_ needed? I mean, we mostly specify the frequency today, so ... why not just always do that for 6 GHz?

I suspect there are people preferring channel numbers as much as there are people preferring frequencies. Personally, I think it is acceptable to put this limitation on 6G.

Quoted 8 lines

:)

After I sent the message I figured maybe then we should have different syntax, where we say prefix the channel number by the band?

iw wlanX set channel 6:149 ...
iw wlanX set channel 5:149 ...
iw wlanX set channel 2.4:11 ...

Do you want to make that band: prefix required or optional. btw. starts to look like the format we use with our wl utility ;-)

Regards,
Arend

#6 lore raw
Quoted 24 lines · Arend Van Spriel
Quoted 23 lines · Johannes Berg
Quoted 11 lines · Arend Van Spriel
Quoted 10 lines · Johannes Berg
Quoted 8 lines · Pradeep Kumar Chitrapu

Channel numbers of 6G band overlaps with those of 2G or 5G bands. Therefore, an optional argument "6G" is added and expected next to channel number to map it to correct 6GHz frequency. If not specified, defaults to matching 2G or 5G frequency.

example:
iw wlanX set channel 149 6G 80MHz --> maps to 6695 MHz
iw wlanX set channel 149 80MHz --> maps to 5745 MHz

Quoted 8 lines
Quoted 4 lines

Hm. I can't really say I like this much.

Is it _really_ needed? I mean, we mostly specify the frequency today, so ... why not just always do that for 6 GHz?

I suspect there are people preferring channel numbers as much as there are people preferring frequencies. Personally, I think it is acceptable to put this limitation on 6G.

:)

Quoted 8 lines
Quoted 6 lines

After I sent the message I figured maybe then we should have different syntax, where we say prefix the channel number by the band?

iw wlanX set channel 6:149 ...
iw wlanX set channel 5:149 ...
iw wlanX set channel 2.4:11 ...

Do you want to make that band: prefix required or optional.

That's a good question. Probably should be optional, otherwise everything breaks ...

Quoted 2 lines

btw. starts
to look like the format we use with our wl utility ;-)

Hah! Maybe you have a better idea there? :)

johannes

#7 lore raw
Quoted 28 lines · Johannes Berg
Quoted 27 lines · Arend Van Spriel
Quoted 26 lines · Johannes Berg
Quoted 11 lines · Arend Van Spriel
Quoted 10 lines · Johannes Berg
Quoted 8 lines · Pradeep Kumar Chitrapu

Channel numbers of 6G band overlaps with those of 2G or 5G bands. Therefore, an optional argument "6G" is added and expected next to channel number to map it to correct 6GHz frequency. If not specified, defaults to matching 2G or 5G frequency.

example:
iw wlanX set channel 149 6G 80MHz --> maps to 6695 MHz
iw wlanX set channel 149 80MHz --> maps to 5745 MHz

Quoted 8 lines
Quoted 4 lines

Hm. I can't really say I like this much.

Is it _really_ needed? I mean, we mostly specify the frequency today, so ... why not just always do that for 6 GHz?

I suspect there are people preferring channel numbers as much as there are people preferring frequencies. Personally, I think it is acceptable to put this limitation on 6G.

:)

After I sent the message I figured maybe then we should have different syntax, where we say prefix the channel number by the band?

Quoted 8 lines
Quoted 5 lines
Quoted 3 lines
   iw wlanX set channel 6:149 ...
   iw wlanX set channel 5:149 ...
   iw wlanX set channel 2.4:11 ...

Do you want to make that band: prefix required or optional.

That's a good question. Probably should be optional, otherwise everything breaks ...

Right.

Quoted 4 lines
Quoted 2 lines

btw. starts
to look like the format we use with our wl utility ;-)

Hah! Maybe you have a better idea there? :)

Not really. The above format seems fine as is.

Gr. AvS