hw/arm: sabrelite: Improve emulation fidelity to allow booting upstream U-Boot
cover hw/arm: sabrelite: Improve emulation fidelity to allow booting upstream U-Boot
From: Bin Meng <[email protected]>
At present the upstream U-Boot (as of today, v2021.01-rc3) does not boot on QEMU sabrelite machine.
This fixes several issues to improve emulation fidelity of the i.MX6 sabrelite board. With this series, upstream U-Boot can boot to U-Boot command shell.
Bin Meng (3):
hw/misc: imx6_ccm: Update PMU_MISC0 reset value hw/msic: imx6_ccm: Correct register value for silicon type hw/arm: sabrelite: Connect the Ethernet PHY at address 6
hw/arm/sabrelite.c | 4 ++++ hw/misc/imx6_ccm.c | 4 ++-- 2 files changed, 6 insertions(+), 2 deletions(-)
Signature · 1 line
2.7.4
PATCH 1/3 hw/misc: imx6_ccm: Update PMU_MISC0 reset value
From: Bin Meng <[email protected]>
U-Boot expects PMU_MISC0 register bit 7 is set (see init_bandgap() in arch/arm/mach-imx/mx6/soc.c) during boot. This bit indicates the bandgap has stabilized.
With this change, the latest upstream U-Boot (v2021.01-rc3) for imx6 sabrelite board (mx6qsabrelite_defconfig), with a slight change made by switching CONFIG_OF_SEPARATE to CONFIG_OF_EMBED, boots to U-Boot shell on QEMU with the following command:
$ qemu-system-arm -M sabrelite -m 1G -kernel u-boot -display none \
-serial null -serial stdioBoot log below:
U-Boot 2021.01-rc3 (Dec 12 2020 - 17:40:02 +0800)
CPU: Freescale i.MX?? rev1.0 at 792 MHz
Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Lite Board
Board: SABRE Lite
I2C: ready
DRAM: 1 GiB
force_idle_bus: sda=0 scl=0 sda.gp=0x5c scl.gp=0x55
force_idle_bus: failed to clear bus, sda=0 scl=0
force_idle_bus: sda=0 scl=0 sda.gp=0x6d scl.gp=0x6c
force_idle_bus: failed to clear bus, sda=0 scl=0
force_idle_bus: sda=0 scl=0 sda.gp=0xcb scl.gp=0x5
force_idle_bus: failed to clear bus, sda=0 scl=0
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - No block device, using default environment
In: serial Out: serial Err: serial Net: Board Net Initialization Failed
No ethernet found.
starting USB...
Bus usb@2184000: usb dr_mode not found
USB EHCI 1.00
Bus usb@2184200: USB EHCI 1.00
scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found
Hit any key to stop autoboot: 0
=>
---
hw/misc/imx6_ccm.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
hw/misc/imx6_ccm.c +1 -1
@@ -450,7 +450,7 @@ static void imx6_ccm_reset(DeviceState *dev) s->analog[PMU_REG_3P0 ] =0x00000F74 ; s->analog[PMU_REG_2P5 ] =0x00005071 ; s->analog[PMU_REG_CORE ] =0x00402010 ; - s->analog[PMU_MISC0 ] =0x04000000 ; + s->analog[PMU_MISC0 ] =0x04000080 ; s->analog[PMU_MISC1 ] =0x00000000 ; s->analog[PMU_MISC2 ] =0x00272727 ;
Signature · 1 line
2.7.4
Re: [PATCH 1/3] hw/misc: imx6_ccm: Update PMU_MISC0 reset value
Quoted 60 lines · Bin Meng
From: Bin Meng <[email protected]>
U-Boot expects
PMU_MISC0register bit 7 is set (seeinit_bandgap()inarch/arm/mach-imx/mx6/soc.c) during boot. This bit indicates the bandgap has stabilized.With this change, the latest upstream U-Boot (v2021.01-rc3) for imx6 sabrelite board (
mx6qsabrelite_defconfig), with a slight change made by switchingCONFIG_OF_SEPARATEtoCONFIG_OF_EMBED, boots to U-Boot shell on QEMU with the following command:$ qemu-system-arm -M sabrelite -m 1G -kernel u-boot -display none \ -serial null -serial stdioBoot log below:
U-Boot 2021.01-rc3 (Dec 12 2020 - 17:40:02 +0800)
CPU: Freescale i.MX?? rev1.0 at 792 MHz
Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Lite Board
Board: SABRE Lite
I2C: ready
DRAM: 1 GiB
force_idle_bus: sda=0 scl=0 sda.gp=0x5c scl.gp=0x55
force_idle_bus: failed to clear bus, sda=0 scl=0
force_idle_bus: sda=0 scl=0 sda.gp=0x6d scl.gp=0x6c
force_idle_bus: failed to clear bus, sda=0 scl=0
force_idle_bus: sda=0 scl=0 sda.gp=0xcb scl.gp=0x5
force_idle_bus: failed to clear bus, sda=0 scl=0
MMC:FSL_SDHC: 0,FSL_SDHC: 1
Loading Environment from MMC... *** Warning - No block device, using default environmentIn: serial Out: serial Err: serial Net: Board Net Initialization FailedNo ethernet found.
starting USB...
Bus usb@2184000: usbdr_modenot found
USB EHCI 1.00
Bus usb@2184200: USB EHCI 1.00
scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found
Hit any key to stop autoboot: 0
=>Signed-off-by Bin Meng <[email protected]>---
hw/misc/imx6_ccm.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)hw/misc/imx6_ccm.c +0
-0
hw/misc/imx6_ccm.c static void imx6_ccm_reset(DeviceState *dev) · line 453
Quoted 5 lines
hw/misc/imx6_ccm.c +1
-1@@ -450,7 +450,7 @@ static void imx6_ccm_reset(DeviceState *dev) s->analog[PMU_REG_3P0 ] =0x00000F74 ; s->analog[PMU_REG_2P5 ] =0x00005071 ; s->analog[PMU_REG_CORE ] =0x00402010 ; - s->analog[PMU_MISC0 ] =0x04000000 ; + s->analog[PMU_MISC0 ] =0x04000080 ;
Are the registers different on the imx6ul machine or should a similar change be made to imx6ul_ccm_reset?
Also what is the write behaviour of this bit? If it is RAO/WI then analog_mask needs fixing so a write to the register doesn't reset the state.
Quoted 2 lines
hw/misc/imx6_ccm.c +0
-0s->analog[PMU_MISC1 ] =0x00000000 ; s->analog[PMU_MISC2 ] =0x00272727 ;
Signature · 1 line
Alex Bennée
Re: [PATCH 1/3] hw/misc: imx6_ccm: Update PMU_MISC0 reset value
Quoted 59 lines · Alex Bennée
Quoted 55 lines · Bin Meng
From: Bin Meng <[email protected]>
U-Boot expects
PMU_MISC0register bit 7 is set (seeinit_bandgap()inarch/arm/mach-imx/mx6/soc.c) during boot. This bit indicates the bandgap has stabilized.With this change, the latest upstream U-Boot (v2021.01-rc3) for imx6 sabrelite board (
mx6qsabrelite_defconfig), with a slight change made by switchingCONFIG_OF_SEPARATEtoCONFIG_OF_EMBED, boots to U-Boot shell on QEMU with the following command:$ qemu-system-arm -M sabrelite -m 1G -kernel u-boot -display none \ -serial null -serial stdioBoot log below:
U-Boot 2021.01-rc3 (Dec 12 2020 - 17:40:02 +0800)
CPU: Freescale i.MX?? rev1.0 at 792 MHz
Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Lite Board
Board: SABRE Lite
I2C: ready
DRAM: 1 GiB
force_idle_bus: sda=0 scl=0 sda.gp=0x5c scl.gp=0x55
force_idle_bus: failed to clear bus, sda=0 scl=0
force_idle_bus: sda=0 scl=0 sda.gp=0x6d scl.gp=0x6c
force_idle_bus: failed to clear bus, sda=0 scl=0
force_idle_bus: sda=0 scl=0 sda.gp=0xcb scl.gp=0x5
force_idle_bus: failed to clear bus, sda=0 scl=0
MMC:FSL_SDHC: 0,FSL_SDHC: 1
Loading Environment from MMC... *** Warning - No block device, using default environmentIn: serial Out: serial Err: serial Net: Board Net Initialization FailedNo ethernet found.
starting USB...
Bus usb@2184000: usbdr_modenot found
USB EHCI 1.00
Bus usb@2184200: USB EHCI 1.00
scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found
Hit any key to stop autoboot: 0
=>Signed-off-by Bin Meng <[email protected]>---
hw/misc/imx6_ccm.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
Quoted 13 lines
hw/misc/imx6_ccm.c static void imx6_ccm_reset(DeviceState *dev) · line 453
Quoted 10 lines
hw/misc/imx6_ccm.c +1
-1@@ -450,7 +450,7 @@ static void imx6_ccm_reset(DeviceState *dev) s->analog[PMU_REG_3P0 ] =0x00000F74 ; s->analog[PMU_REG_2P5 ] =0x00005071 ; s->analog[PMU_REG_CORE ] =0x00402010 ; - s->analog[PMU_MISC0 ] =0x04000000 ; + s->analog[PMU_MISC0 ] =0x04000080 ;Are the registers different on the imx6ul machine or should a similar change be made to
imx6ul_ccm_reset?
I am not sure. I did not try the mcimx6ul-evk machine. I only looked at the i.MX6 DQ reference manual, and current user in QEMU of this imx6_ccm is only the sabrelite machine.
Quoted 8 lines
Also what is the write behaviour of this bit? If it is RAO/WI then
analog_maskneeds fixing so a write to the register doesn't reset the state.Quoted 2 lines
hw/misc/imx6_ccm.c +0
-0s->analog[PMU_MISC1 ] =0x00000000 ; s->analog[PMU_MISC2 ] =0x00272727 ;
There is no analog_mask in the imx6_ccm codes. It exists in the imx6ul_ccm however.
The i.MX6 DQ reference manual says this bit is RW, and does not document the behavior of write. AFAICT this bit is only concerned by the bootloader.
Regards,
Bin
Re: [PATCH 1/3] hw/misc: imx6_ccm: Update PMU_MISC0 reset value
Quoted 87 lines · Bin Meng
Quoted 59 lines · Alex Bennée
Quoted 55 lines · Bin Meng
From: Bin Meng <[email protected]>
U-Boot expects
PMU_MISC0register bit 7 is set (seeinit_bandgap()inarch/arm/mach-imx/mx6/soc.c) during boot. This bit indicates the bandgap has stabilized.With this change, the latest upstream U-Boot (v2021.01-rc3) for imx6 sabrelite board (
mx6qsabrelite_defconfig), with a slight change made by switchingCONFIG_OF_SEPARATEtoCONFIG_OF_EMBED, boots to U-Boot shell on QEMU with the following command:$ qemu-system-arm -M sabrelite -m 1G -kernel u-boot -display none \ -serial null -serial stdioBoot log below:
U-Boot 2021.01-rc3 (Dec 12 2020 - 17:40:02 +0800)
CPU: Freescale i.MX?? rev1.0 at 792 MHz
Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Lite Board
Board: SABRE Lite
I2C: ready
DRAM: 1 GiB
force_idle_bus: sda=0 scl=0 sda.gp=0x5c scl.gp=0x55
force_idle_bus: failed to clear bus, sda=0 scl=0
force_idle_bus: sda=0 scl=0 sda.gp=0x6d scl.gp=0x6c
force_idle_bus: failed to clear bus, sda=0 scl=0
force_idle_bus: sda=0 scl=0 sda.gp=0xcb scl.gp=0x5
force_idle_bus: failed to clear bus, sda=0 scl=0
MMC:FSL_SDHC: 0,FSL_SDHC: 1
Loading Environment from MMC... *** Warning - No block device, using default environmentIn: serial Out: serial Err: serial Net: Board Net Initialization FailedNo ethernet found.
starting USB...
Bus usb@2184000: usbdr_modenot found
USB EHCI 1.00
Bus usb@2184200: USB EHCI 1.00
scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found
Hit any key to stop autoboot: 0
=>Signed-off-by Bin Meng <[email protected]>---
hw/misc/imx6_ccm.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)Quoted 13 lines
hw/misc/imx6_ccm.c static void imx6_ccm_reset(DeviceState *dev) · line 453
Quoted 10 lines
hw/misc/imx6_ccm.c +1
-1@@ -450,7 +450,7 @@ static void imx6_ccm_reset(DeviceState *dev) s->analog[PMU_REG_3P0 ] =0x00000F74 ; s->analog[PMU_REG_2P5 ] =0x00005071 ; s->analog[PMU_REG_CORE ] =0x00402010 ; - s->analog[PMU_MISC0 ] =0x04000000 ; + s->analog[PMU_MISC0 ] =0x04000080 ;Are the registers different on the imx6ul machine or should a similar change be made to
imx6ul_ccm_reset?I am not sure. I did not try the mcimx6ul-evk machine. I only looked at the i.MX6 DQ reference manual, and current user in QEMU of this
imx6_ccmis only the sabrelite machine.Quoted 8 lines
Also what is the write behaviour of this bit? If it is RAO/WI then
analog_maskneeds fixing so a write to the register doesn't reset the state.Quoted 2 lines
hw/misc/imx6_ccm.c +0
-0s->analog[PMU_MISC1 ] =0x00000000 ; s->analog[PMU_MISC2 ] =0x00272727 ;
Quoted 6 lines
There is no
analog_maskin theimx6_ccmcodes. It exists in theimx6ul_ccmhowever.The i.MX6 DQ reference manual says this bit is RW, and does not document the behavior of write. AFAICT this bit is only concerned by the bootloader.
My bad - I was grepping for PMU_MISC0. It would be nice to nail down if there is any similarity between the two instances. Doing a diff between the two does look pretty similar which makes me wonder if there is scope for a more generic shared code implementation with a few feature flags. I suspect that is a more involved job however which is out of scope for this series.
Quoted 3 lines
Regards,
Bin
Signature · 1 line
Alex Bennée
Re: [PATCH 1/3] hw/misc: imx6_ccm: Update PMU_MISC0 reset value
In reply to Bin MengQuoted 83 lines · Bin Meng
Quoted 59 lines · Alex Bennée
Quoted 55 lines · Bin Meng
From: Bin Meng <[email protected]>
U-Boot expects
PMU_MISC0register bit 7 is set (seeinit_bandgap()inarch/arm/mach-imx/mx6/soc.c) during boot. This bit indicates the bandgap has stabilized.With this change, the latest upstream U-Boot (v2021.01-rc3) for imx6 sabrelite board (
mx6qsabrelite_defconfig), with a slight change made by switchingCONFIG_OF_SEPARATEtoCONFIG_OF_EMBED, boots to U-Boot shell on QEMU with the following command:$ qemu-system-arm -M sabrelite -m 1G -kernel u-boot -display none \ -serial null -serial stdioBoot log below:
U-Boot 2021.01-rc3 (Dec 12 2020 - 17:40:02 +0800)
CPU: Freescale i.MX?? rev1.0 at 792 MHz
Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Lite Board
Board: SABRE Lite
I2C: ready
DRAM: 1 GiB
force_idle_bus: sda=0 scl=0 sda.gp=0x5c scl.gp=0x55
force_idle_bus: failed to clear bus, sda=0 scl=0
force_idle_bus: sda=0 scl=0 sda.gp=0x6d scl.gp=0x6c
force_idle_bus: failed to clear bus, sda=0 scl=0
force_idle_bus: sda=0 scl=0 sda.gp=0xcb scl.gp=0x5
force_idle_bus: failed to clear bus, sda=0 scl=0
MMC:FSL_SDHC: 0,FSL_SDHC: 1
Loading Environment from MMC... *** Warning - No block device, using default environmentIn: serial Out: serial Err: serial Net: Board Net Initialization FailedNo ethernet found.
starting USB...
Bus usb@2184000: usbdr_modenot found
USB EHCI 1.00
Bus usb@2184200: USB EHCI 1.00
scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found
Hit any key to stop autoboot: 0
=>Signed-off-by Bin Meng <[email protected]>---
hw/misc/imx6_ccm.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)Quoted 13 lines
hw/misc/imx6_ccm.c static void imx6_ccm_reset(DeviceState *dev) · line 453
Quoted 10 lines
hw/misc/imx6_ccm.c +1
-1@@ -450,7 +450,7 @@ static void imx6_ccm_reset(DeviceState *dev) s->analog[PMU_REG_3P0 ] =0x00000F74 ; s->analog[PMU_REG_2P5 ] =0x00005071 ; s->analog[PMU_REG_CORE ] =0x00402010 ; - s->analog[PMU_MISC0 ] =0x04000000 ; + s->analog[PMU_MISC0 ] =0x04000080 ;Are the registers different on the imx6ul machine or should a similar change be made to
imx6ul_ccm_reset?I am not sure. I did not try the mcimx6ul-evk machine. I only looked at the i.MX6 DQ reference manual, and current user in QEMU of this
imx6_ccmis only the sabrelite machine.Quoted 5 lines
Also what is the write behaviour of this bit? If it is RAO/WI then
analog_maskneeds fixing so a write to the register doesn't reset the state.
Quoted 6 lines
Quoted 3 lines
hw/misc/imx6_ccm.c static void imx6_ccm_reset(DeviceState *dev) · line 455
Quoted 2 lines
hw/misc/imx6_ccm.c +0
-0s->analog[PMU_MISC1 ] =0x00000000 ; s->analog[PMU_MISC2 ] =0x00272727 ;There is no
analog_maskin theimx6_ccmcodes. It exists in theimx6ul_ccmhowever.
My bad - I was grepping for PMU_MISC0. It would be nice to nail down if there is any similarity between the two instances. Doing a diff between the two does look pretty similar which makes me wonder if there is scope for a more generic shared code implementation with a few feature flags. I suspect that is a more involved job however which is out of scope for this series.
Quoted 7 lines
The i.MX6 DQ reference manual says this bit is RW, and does not document the behavior of write. AFAICT this bit is only concerned by the bootloader.
Regards,
Bin
Signature · 1 line
Alex Bennée
PATCH 2/3 hw/msic: imx6_ccm: Correct register value for silicon type
In reply to Bin MengFrom: Bin Meng <[email protected]>
Currently when U-Boot boots, it prints "??" for i.MX processor:
CPU: Freescale i.MX?? rev1.0 at 792 MHz
The register that was used to determine the silicon type is undocumented in the latest IMX6DQRM (Rev. 6, 05/2020), but we can refer to get_cpu_rev() in arch/arm/mach-imx/mx6/soc.c in the U-Boot source codes that USB_ANALOG_DIGPROG is used.
Update its reset value to indicate i.MX6Q.
---
hw/misc/imx6_ccm.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
hw/misc/imx6_ccm.c +1 -1
@@ -462,7 +462,7 @@ static void imx6_ccm_reset(DeviceState *dev) s->analog[USB_ANALOG_USB2_VBUS_DETECT ] =0x00000004 ; s->analog[USB_ANALOG_USB2_CHRG_DETECT ] =0x00000000 ; s->analog[USB_ANALOG_USB2_MISC ] =0x00000002 ; - s->analog[USB_ANALOG_DIGPROG ] =0x00000000 ; + s->analog[USB_ANALOG_DIGPROG ] =0x00630000 ;/* all PLLs need to be locked */ s->analog[CCM_ANALOG_PLL_ARM ] |=CCM_ANALOG_PLL_LOCK ;
Signature · 1 line
2.7.4
PATCH 3/3 hw/arm: sabrelite: Connect the Ethernet PHY at address 6
In reply to Bin MengFrom: Bin Meng <[email protected]>
At present, when booting U-Boot on QEMU sabrelite, we see:
Net: Board Net Initialization Failed
No ethernet found.
U-Boot scans PHY at address 4/5/6/7 (see board_eth_init() in the U-Boot source: board/boundary/nitrogen6x/nitrogen6x.c). On the real board, the Ethernet PHY is at address 6. Adjust this by updating the "fec-phy-num" property of the fsl_imx6 SoC object.
With this change, U-Boot sees the PHY but complains MAC address:
Net: using phy at 6
FEC [PRIME]
Error: FEC address not set.
This is due to U-Boot tries to read the MAC address from the fuse, which QEMU does not have any valid content filled in. However this does not prevent the Ethernet from working in QEMU. We just need to set up the MAC address later in the U-Boot command shell, by:
=> setenv ethaddr 00:11:22:33:44:55
---
hw/arm/sabrelite.c | 4 ++++ 1 file changed, 4 insertions(+)
hw/arm/sabrelite.c +4 -0
@@ -51,6 +51,10 @@ static void sabrelite_init(MachineState *machine) s =FSL_IMX6 (object_new (TYPE_FSL_IMX6 ));object_property_add_child (OBJECT (machine),"soc" ,OBJECT (s)); + +/* Ethernet PHY address is 6 */ +object_property_set_int (OBJECT (s),"fec-phy-num" ,6 , &error_fatal); +qdev_realize (DEVICE (s),NULL , &error_fatal); memory_region_add_subregion(get_system_memory(), FSL_IMX6_MMDC_ADDR,
Signature · 1 line
2.7.4
Re: [PATCH 3/3] hw/arm: sabrelite: Connect the Ethernet PHY at address 6
Quoted 18 lines · Bin Meng
From: Bin Meng <[email protected]>
At present, when booting U-Boot on QEMU sabrelite, we see:
Net: Board Net Initialization Failed
No ethernet found.U-Boot scans PHY at address 4/5/6/7 (see
board_eth_init()in the U-Boot source:board/boundary/nitrogen6x/nitrogen6x.c). On the real board, the Ethernet PHY is at address 6. Adjust this by updating the "fec-phy-num" property of thefsl_imx6SoC object.With this change, U-Boot sees the PHY but complains MAC address:
Net: using phy at 6
FEC [PRIME]
Error: FEC address not set.
Quoted 8 lines
This is due to U-Boot tries to read the MAC address from the fuse, which QEMU does not have any valid content filled in. However this does not prevent the Ethernet from working in QEMU. We just need to set up the MAC address later in the U-Boot command shell, by:
=> setenv ethaddr 00:11:22:33:44:55
Signed-off-by Bin Meng <[email protected]>
As you are giving this board some attention is there any chance you could be persuaded to add an entry in docs/system/arm (linked from docs/system/target-arm.rst) to briefly describe the board and what is known to work and boot on it?
Signature · 1 line
Alex Bennée
Re: [PATCH 3/3] hw/arm: sabrelite: Connect the Ethernet PHY at address 6
Quoted 27 lines · Alex Bennée
Quoted 23 lines · Bin Meng
From: Bin Meng <[email protected]>
At present, when booting U-Boot on QEMU sabrelite, we see:
Net: Board Net Initialization Failed
No ethernet found.U-Boot scans PHY at address 4/5/6/7 (see
board_eth_init()in the U-Boot source:board/boundary/nitrogen6x/nitrogen6x.c). On the real board, the Ethernet PHY is at address 6. Adjust this by updating the "fec-phy-num" property of thefsl_imx6SoC object.With this change, U-Boot sees the PHY but complains MAC address:
Net: using phy at 6
FEC [PRIME]
Error: FEC address not set.This is due to U-Boot tries to read the MAC address from the fuse, which QEMU does not have any valid content filled in. However this does not prevent the Ethernet from working in QEMU. We just need to set up the MAC address later in the U-Boot command shell, by:
Quoted 6 lines
Quoted 3 lines
=> setenv ethaddr 00:11:22:33:44:55
Signed-off-by Bin Meng <[email protected]>Reviewed-by Alex Bennée <[email protected]>
Thanks for the review.
Quoted 4 lines
As you are giving this board some attention is there any chance you could be persuaded to add an entry in docs/system/arm (linked from
docs/system/target-arm.rst) to briefly describe the board and what is known to work and boot on it?
Sure, I will try to add something for this board in v2.
Regards,
Bin
Quoted 4 lines · Bin Meng
From: Bin Meng <[email protected]>
At present the upstream U-Boot (as of today, v2021.01-rc3) does not boot on QEMU sabrelite machine.
Are there any public build artefacts for u-boot on saberlite that could be used for an acceptance test?
Quoted 13 lines
This fixes several issues to improve emulation fidelity of the i.MX6 sabrelite board. With this series, upstream U-Boot can boot to U-Boot command shell.
Bin Meng (3):
hw/misc:imx6_ccm: UpdatePMU_MISC0reset value hw/msic:imx6_ccm: Correct register value for silicon type hw/arm: sabrelite: Connect the Ethernet PHY at address 6hw/arm/sabrelite.c | 4 ++++ hw/misc/imx6_ccm.c | 4 ++-- 2 files changed, 6 insertions(+), 2 deletions(-)
Signature · 1 line
Alex Bennée
Quoted 11 lines · Alex Bennée
Quoted 4 lines · Bin Meng
From: Bin Meng <[email protected]>
At present the upstream U-Boot (as of today, v2021.01-rc3) does not boot on QEMU sabrelite machine.
Are there any public build artefacts for u-boot on saberlite that could be used for an acceptance test?
I am not aware of one. Upstream U-Boot has build pipelines but it does not publish artifacts.
Quoted 5 lines
Quoted 5 lines
This fixes several issues to improve emulation fidelity of the i.MX6 sabrelite board. With this series, upstream U-Boot can boot to U-Boot command shell.
Regards,
Bin