8139too on ABIT BP6 causes "eth0: transmit timed out"
I'm running:
Linux nice 2.4.12-ac3 #1 SMP Sat Oct 20 16:21:24 MEST 2001 i686 unknown
but this problem is not specific to that kernel. I've been having it for a looong time.
Specifically, I get:
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Tx queue start entry 32190531 dirty entry 32190527.
eth0: Tx descriptor 0 is 00002000. eth0: Tx descriptor 1 is 00002000. eth0: Tx descriptor 2 is 00002000. eth0: Tx descriptor 3 is 00002000. (queue head)
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
and then the machine is dead, network-wise. I have to reboot (reset).
Note that I am on an ABIT BP6 board, and I do get a lot of APIC errors under heavy network traffic, which is what raises the above. By heavy network traffic, I mean a 7 Mb/s full duplex (it's a 100 Mb/s LAN).
I suspect that somewhere, the APIC gets hosed and looses an interrupt, and then the ethernet driver no longer processes its queue. Is there anything that can be done to reset the hardware state more fully when this occurs?
Raphael
APM disable broken (was -> Re: 8139too on ABIT BP6 causes "eth0: transmit timed out" )
Raphael Manfredi <[email protected]> wrote:
...[recent 2.4-based kernel]...
Quoted 6 lines
but this problem is not specific to that kernel. I've been having it for a looong time.
Specifically, I get:
NETDEV WATCHDOG: eth0: transmit timed out
...
Quoted 6 lines
and then the machine is dead, network-wise. I have to reboot (reset).
Note that I am on an ABIT BP6 board, and I do get a lot of APIC errors under heavy network traffic, which is what raises the above. By heavy network traffic, I mean a 7 Mb/s full duplex (it's a 100 Mb/s LAN).
I had what looks like exactly this problem with my ABIT BP6 -based machine running RH 7.1, and the problem turned out to be the interaction between SMP and the APM BIOS, when APM is turned on. A different network card, but the same symptom. Another symptom I would occasionally see was a certain kind of hard-disk hang, but only on the integrated HPT366 controller.
I suggest you try either:
-- adding the "noapic" line to your kernel command-line (which will
lose you some I/O performance since normal interrupts will not be handled APIC-style)
-- completely disabling APM from your kernel configuration. Using
"apm=off/disabled" (I can't remember the exact one you're supposed to use here) does not totally disable APM usage.
This brings me to my other point. During the Linux kernel startup code (in the early assembly), the APM BIOS checking code leaves the BIOS in the "connected" state even if the kernel option for disabling APM or the SMP forced disable of APM is triggered.
This makes various motherboards (such as the ABIT BP6) unstable.
The Right Thing to do would be to disconnect the APM BIOS if it is determined that APM support should be disabled.
I could probably generate a patch to fix this if it looked like it would be accepted by the folks maintaining APM support...
--
Erich Stefan Boleyn <[email protected]> http://www.uruk.org/
"Reality is truly stranger than fiction; Probably why fiction is so popular"
Re: APM disable broken (was -> Re: 8139too on ABIT BP6 causes "eth0: transmit timed out" )
Hello erich,
Monday, October 29, 2001, 12:11:27 AM, you wrote:
i have a dual celeron in a bp6, i reflash de bios with
http://bp6.gamesquad.net/bios.phtml the bios revision Final RU BIOS (newest Fianl Release BIOS from Abit)
and i have a ovislink 8139C chip and a hp 100mb switch and all works fine
euo> Raphael Manfredi <[email protected]> wrote:
euo> ...[recent 2.4-based kernel]...
Quoted 6 lines
Quoted 6 lines
but this problem is not specific to that kernel. I've been having it for a looong time.
Specifically, I get:
NETDEV WATCHDOG: eth0: transmit timed out
euo> ...
Quoted 6 lines
Quoted 6 lines
and then the machine is dead, network-wise. I have to reboot (reset).
Note that I am on an ABIT BP6 board, and I do get a lot of APIC errors under heavy network traffic, which is what raises the above. By heavy network traffic, I mean a 7 Mb/s full duplex (it's a 100 Mb/s LAN).
euo> I had what looks like exactly this problem with my ABIT BP6 -based machine euo> running RH 7.1, and the problem turned out to be the interaction between euo> SMP and the APM BIOS, when APM is turned on. A different network card, euo> but the same symptom. Another symptom I would occasionally see was a euo> certain kind of hard-disk hang, but only on the integrated HPT366 euo> controller.
euo> I suggest you try either:
euo> -- adding the "noapic" line to your kernel command-line (which will euo> lose you some I/O performance since normal interrupts will not be euo> handled APIC-style) euo> -- completely disabling APM from your kernel configuration. Using euo> "apm=off/disabled" (I can't remember the exact one you're supposed euo> to use here) does not totally disable APM usage.
euo> This brings me to my other point. During the Linux kernel startup euo> code (in the early assembly), the APM BIOS checking code leaves the euo> BIOS in the "connected" state even if the kernel option for disabling euo> APM or the SMP forced disable of APM is triggered.
euo> This makes various motherboards (such as the ABIT BP6) unstable.
euo> The Right Thing to do would be to disconnect the APM BIOS if it is euo> determined that APM support should be disabled.
euo> I could probably generate a patch to fix this if it looked like it would euo> be accepted by the folks maintaining APM support...
euo> --
euo> Erich Stefan Boleyn <[email protected]> http://www.uruk.org/
euo> "Reality is truly stranger than fiction; Probably why fiction is so popular" euo> -
euo> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in euo> the body of a message to [email protected]
euo> More majordomo info at http://vger.kernel.org/majordomo-info.html
euo> Please read the FAQ at http://www.tux.org/lkml/
Signature · 2 lines
Best regards, victor mailto:[email protected]
Re: APM disable broken (was -> Re: 8139too on ABIT BP6 causes "eth0: transmit timed out" )
In reply to [email protected]Quoted 20 lines · On Mondayen den 29 October 2001 00.11, [email protected] wrote:
Raphael Manfredi <[email protected]> wrote:
...[recent 2.4-based kernel]...
Quoted 6 lines
but this problem is not specific to that kernel. I've been having it for a looong time.
Specifically, I get:
NETDEV WATCHDOG: eth0: transmit timed out
...
Quoted 6 lines
and then the machine is dead, network-wise. I have to reboot (reset).
Note that I am on an ABIT BP6 board, and I do get a lot of APIC errors under heavy network traffic, which is what raises the above. By heavy network traffic, I mean a 7 Mb/s full duplex (it's a 100 Mb/s LAN).
Quoted 6 lines
I had what looks like exactly this problem with my ABIT BP6 -based machine running RH 7.1, and the problem turned out to be the interaction between SMP and the APM BIOS, when APM is turned on. A different network card, but the same symptom. Another symptom I would occasionally see was a certain kind of hard-disk hang, but only on the integrated HPT366 controller.
You might want to try the latest Abit BP6 "RU" bios with HPT366 bios v1.28, get it at:
ftp://ftp.mathematik.uni-marburg.de/pub/mirror/abit/beta/bp6/bios/128/bp6ru128.zip
Chears.
Signature · 6 lines
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- | Oden Eriksson, Deserve-IT Networks, Jokkmokk, Sweden. | Mandrake Linux release 8.2 (Cooker) for i586 | Current uptime with kernel 2.4.12-6mdksmp: 14min | cpu0 @ 814.28 bm, fan 4500 rpm, temp +31.0°C | cpu1 @ 815.92 bm, fan 4500 rpm, temp +29°C
Quoted 11 lines · Raphael Manfredi
Specifically, I get:
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Tx queue start entry 32190531 dirty entry 32190527.eth0: Tx descriptor 0 is 00002000. eth0: Tx descriptor 1 is 00002000. eth0: Tx descriptor 2 is 00002000. eth0: Tx descriptor 3 is 00002000. (queue head)eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
and then the machine is dead, network-wise. I have to reboot (reset).
I have this problem when I compile the driver with PIO mode, except it is that way as soon as the card is initalized. The only way for me to use PIO is to put the Becker driver in its place.
-D
Quoting Martin Eriksson <[email protected]> from ml.linux.kernel:
:What Bios are you running? You should be running the modified RU1.25 Bios, :and have enabled MPS 1.4. Also disable "Spread Spectrum" and do *not* :overclock.
I have the RU BIOS, I enabled MPS 1.4.
What is "Spread Spectrum?".
I don't overclock. I never do.
I remember seeing messages about network lockups on the ABIT BP6, and there was a patch submitted to the list. It had to do with a Sysreq patch that would "do something to the APIC" and re-enable network interrupts.
However, I don't remember who this was, and where the patch is.
Is the older Becker driver for the RTL8139 more robust? I know it's no longer maintained, but if I want to try it, how do I proceed? I don't remember seeing it offered in the configuration menu.
Raphael