net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCs
Subsystems (3)
PATCH v2 1/3 net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCs
From: Aaron Tseng <[email protected]>
Add Cortina Access Ethernet device driver for CAxxxx SoCs. This driver supports both legacy and DM_ETH network models.
---
Changes in v2:
- clean up old debug code
- reference CRC functions already provided in u-boot core
- remove unused code, ex: CA_IN/CA_OUT
- refactor the design of register read/write, union -> struct
- remove platform dependent code
MAINTAINERS | 4 + drivers/net/Kconfig | 7 + drivers/net/Makefile | 1 + drivers/net/cortina_ni.c | 1103 ++++++++++++++++++++++++++++++++++++++++++++++ drivers/net/cortina_ni.h | 401 +++++++++++++++++ 5 files changed, 1516 insertions(+) create mode 100644 drivers/net/cortina_ni.c create mode 100644 drivers/net/cortina_ni.h
MAINTAINERS +4 -0
@@ -198,6 +198,8 @@ F: drivers/mmc/ca_dw_mmc.c F: drivers/spi/ca_sflash.c F: drivers/i2c/i2c-cortina.c F: drivers/i2c/i2c-cortina.h +F: drivers/net/cortina_ni.c +F: drivers/net/cortina_ni.h ARM/CZ.NIC TURRIS MOX SUPPORT M: Marek Behun <[email protected]>
@@ -806,6 +808,8 @@ F: drivers/mmc/ca_dw_mmc.c F: drivers/spi/ca_sflash.c F: drivers/i2c/i2c-cortina.c F: drivers/i2c/i2c-cortina.h +F: drivers/net/cortina_ni.c +F: drivers/net/cortina_ni.h MIPS MSCC M: Gregory CLEMENT <[email protected]>
drivers/net/Kconfig +7 -0
@@ -149,6 +149,13 @@ config BCMGENET help This driver supports the BCMGENET Ethernet MAC. +config CORTINA_NI_ENET + bool "Cortina-Access Ethernet driver" + depends on DM_ETH && CORTINA_PLATFORM + help + This driver supports the Cortina-Access Ethernet MAC for + all supported CAxxxx SoCs. + config DWC_ETH_QOS bool "Synopsys DWC Ethernet QOS device support" depends on DM_ETH
drivers/net/Makefile +1 -0
@@ -14,6 +14,7 @@ obj-$(CONFIG_DRIVER_AX88180) += ax88180.o obj-$(CONFIG_BCM_SF2_ETH) += bcm-sf2-eth.o obj-$(CONFIG_BCM_SF2_ETH_GMAC) += bcm-sf2-eth-gmac.o obj-$(CONFIG_CALXEDA_XGMAC) += calxedaxgmac.o +obj-$(CONFIG_CORTINA_NI_ENET) += cortina_ni.o obj-$(CONFIG_CS8900) += cs8900.o obj-$(CONFIG_TULIP) += dc2114x.o obj-$(CONFIG_ETH_DESIGNWARE) += designware.o
drivers/net/cortina_ni.c new file +1103 -0
1,103 lines not on this page · raw message
drivers/net/cortina_ni.h new file +401 -0
401 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 2/3 net: phy: ca_phy: Add driver for CAxxxx SoCs
From: Abbie Chang <[email protected]>
Add phy driver support for MACs embedded inside Cortina Access SoCs
Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver
---
Changes in v2: None
MAINTAINERS | 2 + drivers/net/phy/Kconfig | 7 +++ drivers/net/phy/Makefile | 1 + drivers/net/phy/ca_phy.c | 133 +++++++++++++++++++++++++++++++++++++++++++++++ drivers/net/phy/phy.c | 3 ++ include/phy.h | 1 + 6 files changed, 147 insertions(+) create mode 100644 drivers/net/phy/ca_phy.c
MAINTAINERS +2 -0
@@ -200,6 +200,7 @@ F: drivers/i2c/i2c-cortina.c F: drivers/i2c/i2c-cortina.h F: drivers/net/cortina_ni.c F: drivers/net/cortina_ni.h +F: drivers/net/phy/ca_phy.c ARM/CZ.NIC TURRIS MOX SUPPORT M: Marek Behun <[email protected]>
@@ -810,6 +811,7 @@ F: drivers/i2c/i2c-cortina.c F: drivers/i2c/i2c-cortina.h F: drivers/net/cortina_ni.c F: drivers/net/cortina_ni.h +F: drivers/net/phy/ca_phy.c MIPS MSCC M: Gregory CLEMENT <[email protected]>
drivers/net/phy/Kconfig +7 -0
@@ -131,6 +131,13 @@ config SYS_CORTINA_FW_IN_SPIFLASH endchoice +config PHY_CORTINA_ACCESS + bool "Cortina Access Ethernet PHYs support" + default y + depends on CORTINA_NI_ENET + help + Cortina Access Ethernet PHYs init process + config PHY_DAVICOM bool "Davicom Ethernet PHYs support"
drivers/net/phy/Makefile +1 -0
@@ -14,6 +14,7 @@ obj-$(CONFIG_PHY_AQUANTIA) += aquantia.o obj-$(CONFIG_PHY_ATHEROS) += atheros.o obj-$(CONFIG_PHY_BROADCOM) += broadcom.o obj-$(CONFIG_PHY_CORTINA) += cortina.o +obj-$(CONFIG_PHY_CORTINA_ACCESS) += ca_phy.o obj-$(CONFIG_PHY_DAVICOM) += davicom.o obj-$(CONFIG_PHY_ET1011C) += et1011c.o obj-$(CONFIG_PHY_LXT) += lxt.o
drivers/net/phy/ca_phy.c new file +133 -0
133 lines not on this page · raw message
drivers/net/phy/phy.c +3 -0
@@ -500,6 +500,9 @@ int phy_init(void)#ifdef CONFIG_PHY_CORTINA phy_cortina_init ();#endif +#ifdef CONFIG_PHY_CORTINA_ACCESS +phy_cortina_access_init (); +#endif #ifdef CONFIG_PHY_DAVICOM phy_davicom_init ();#endif
include/phy.h +1 -0
@@ -493,6 +493,7 @@ int phy_aquantia_init(void);int phy_atheros_init (void );int phy_broadcom_init (void );int phy_cortina_init (void ); +int phy_cortina_access_init (void );int phy_davicom_init (void );int phy_et1011c_init (void );int phy_lxt_init (void );
Signature · 1 line
2.7.4
PATCH v2 2/3 net: phy: ca_phy: Add driver for CAxxxx SoCs
Quoted 7 lines · Alex Nemirovsky
From: Abbie Chang <[email protected]>
Add phy driver support for MACs embedded inside Cortina Access SoCs
Signed-off-by Abbie Chang <[email protected]>Signed-off-by Alex Nemirovsky <[email protected]>
Quoted 6 lines
CC Joe Hershberger <[email protected]>CC Tom Rini <[email protected]>CC Aaron Tseng <[email protected]>Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20210127/f40f6559/attachment.sig>
PATCH v2 3/3 board: presidio-asic: Add CAxxxx Ethernet support
In reply to Alex NemirovskyAdd CAxxxx Ethernet support for the Cortina Access Presidio Engineering Board
---
Changes in v2:
- only support DM_ETH network models by removing
code for legacy mode support
arch/arm/dts/ca-presidio-engboard.dts | 31 ++++++++++++++++++++++++++++ configs/cortina_presidio-asic-emmc_defconfig | 4 +++- include/configs/presidio_asic.h | 15 +++++++++++++- 3 files changed, 48 insertions(+), 2 deletions(-)
arch/arm/dts/ca-presidio-engboard.dts +31 -0
@@ -95,4 +95,35 @@ }; }; + + eth: ethnet at 0xf4300000 { + compatible = "eth_cortina"; + reg = <0x0 0xf4320000 0x34>, + <0x0 0xf43290d8 0x04>, + <0x0 0xf4304000 0x04>; + + /* port0: phy address 1 - GMAC0: port 0 + * port1: phy address 2 - GMAC1: port 1 + * port2: phy address 3 - GMAC2: port 2 + * port3: phy address 4 - GMAC3: port 3 + * port4: phy address 5 - RGMII: port 4 + */ + valid-port-map = <0x1f>; + valid-port-num = <5>; + valid-ports = <0x1 0x0>, + <0x2 0x1>, + <0x3 0x2>, + <0x4 0x3>, + <0x5 0x4>; + def-active-port = <0x3>; + inter-gphy-num = <6>; + inter-gphy-val = <0xf43380fc 0xbcd>, + <0xf43380dc 0xeeee>, + <0xf43380d8 0xeeee>, + <0xf43380fc 0xbce>, + <0xf43380c0 0x7777>, + <0xf43380c4 0x7777>; + init-rgmii = <1>; + ni-xram-base = <0xF4500000>; + }; };
configs/cortina_presidio-asic-emmc_defconfig +3 -1
@@ -22,7 +22,6 @@ CONFIG_CMD_EXT2=y CONFIG_CMD_EXT4=y CONFIG_OF_CONTROL=y CONFIG_OF_LIVE=y -# CONFIG_NET is not set CONFIG_DM=y CONFIG_CORTINA_GPIO=y CONFIG_DM_I2C=y
@@ -30,6 +29,9 @@ CONFIG_SYS_I2C_CA=y CONFIG_DM_MMC=y CONFIG_MMC_DW=y CONFIG_MMC_DW_CORTINA=y +CONFIG_PHYLIB=y +CONFIG_DM_ETH=y +CONFIG_CORTINA_NI_ENET=y CONFIG_DM_SERIAL=y CONFIG_CORTINA_UART=y CONFIG_WDT=y
include/configs/presidio_asic.h +14 -1
@@ -2,7 +2,7 @@/* * Copyright (C) 2020 Cortina Access Inc. * -* Configuration for Cortina-Access Presidio board. +* Configuration for Cortina-Access Presidio board */ #ifndef __PRESIDIO_ASIC_H
@@ -63,6 +63,19 @@ sizeof(CONFIG_SYS_PROMPT) + 16)#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define KSEG1_ATU_XLAT (x) (x) + +/* HW REG ADDR */ +#define NI_READ_POLL_COUNT 1000 +#define CA_NI_MDIO_REG_BASE 0xF4338 +#define NI_HV_GLB_MAC_ADDR_CFG0_OFFSET 0x010 +#define NI_HV_GLB_MAC_ADDR_CFG1_OFFSET 0x014 +#define NI_HV_PT_BASE 0x400 +#define NI_HV_XRAM_BASE 0x820 +#define GLOBAL_BLOCK_RESET_OFFSET 0x04 +#define GLOBAL_GLOBAL_CONFIG_OFFSET 0x20 +#define GLOBAL_IO_DRIVE_CONTROL_OFFSET 0x4c +/* max command args */ #define CONFIG_SYS_MAXARGS 64#define CONFIG_EXTRA_ENV_SETTINGS "silent=y\0"
Signature · 1 line
2.7.4
PATCH v2 3/3 board: presidio-asic: Add CAxxxx Ethernet support
Quoted 5 lines · Alex Nemirovsky
Add CAxxxx Ethernet support for the Cortina Access Presidio Engineering Board
Signed-off-by Alex Nemirovsky <[email protected]>CC Tom Rini <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20210127/bb7f9bb5/attachment.sig>
PATCH v2 1/3 net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCs
In reply to Alex NemirovskyQuoted 5 lines · Alex Nemirovsky
From: Aaron Tseng <[email protected]>
Add Cortina Access Ethernet device driver for CAxxxx SoCs. This driver supports both legacy and
DM_ETHnetwork models.
Quoted 7 lines
Signed-off-by Aaron Tseng <[email protected]>Signed-off-by Alex Nemirovsky <[email protected]>Signed-off-by Abbie Chang <[email protected]>CC Joe Hershberger <[email protected]>CC Abbie Chang <[email protected]>CC Tom Rini <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20210127/454f6e22/attachment.sig>