phy: phy-imx8mq-usb: Add USB PHY driver for i.MX8MQ
PATCH 1/4 phy: phy-imx8mq-usb: Add USB PHY driver for i.MX8MQ
Add the USB PHY driver for i.MX8MQ to work with DWC3 USB controller.
--- drivers/phy/Kconfig | 7 ++ drivers/phy/Makefile | 1 + drivers/phy/phy-imx8mq-usb.c | 197 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 205 insertions(+) create mode 100644 drivers/phy/phy-imx8mq-usb.c
drivers/phy/Kconfig +7 -0
@@ -268,5 +268,12 @@ config PHY_MTK_TPHY multi-ports is first version, otherwise is second veriosn, so you can easily distinguish them by banks layout. +config PHY_IMX8MQ_USB + bool "NXP i.MX8MQ USB PHY Driver" + depends on PHY + depends on IMX8MQ + help + Support the USB3.0 PHY in NXP i.MX8MQ SoC + source "drivers/phy/rockchip/Kconfig" endmenu
drivers/phy/Makefile +1 -0
@@ -31,3 +31,4 @@ obj-$(CONFIG_MT7620_USB_PHY) += mt7620-usb-phy.o obj-$(CONFIG_MT76X8_USB_PHY) += mt76x8-usb-phy.o obj-$(CONFIG_PHY_DA8XX_USB) += phy-da8xx-usb.o obj-$(CONFIG_PHY_MTK_TPHY) += phy-mtk-tphy.o +obj-$(CONFIG_PHY_IMX8MQ_USB) += phy-imx8mq-usb.o
drivers/phy/phy-imx8mq-usb.c new file +197 -0
197 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH 2/4 arm: dts: imx8mq: Add alias for two usb controllers
Add alias for two DWC3 usb controllers to fix the seq index.
--- arch/arm/dts/imx8mq.dtsi | 2 ++ 1 file changed, 2 insertions(+)
arch/arm/dts/imx8mq.dtsi +2 -0
@@ -39,6 +39,8 @@ spi0 = &ecspi1; spi1 = &ecspi2; spi2 = &ecspi3; + usb0 = &usb_dwc3_0; + usb1 = &usb_dwc3_1; }; ckil: clock-ckil {
Signature · 1 line
2.7.4
Re: [PATCH 2/4] arm: dts: imx8mq: Add alias for two usb controllers
Am Sun, Feb 21, 2021 at 08:26:22AM -0800 schrieb Ye Li:
Quoted 12 lines
Add alias for two DWC3 usb controllers to fix the seq index.
Signed-off-by Ye Li <[email protected]>--- arch/arm/dts/imx8mq.dtsi | 2 ++ 1 file changed, 2 insertions(+)arch/arm/dts/imx8mq.dtsi +0
-0
arch/arm/dts/imx8mq.dtsi line 43
Quoted 5 lines
arch/arm/dts/imx8mq.dtsi +2
-0@@ -39,6 +39,8 @@ spi0 = &ecspi1; spi1 = &ecspi2; spi2 = &ecspi3; + usb0 = &usb_dwc3_0; + usb1 = &usb_dwc3_1;
I'm not sure what the policy is. Should changes to the device tree be put into the u-boot.dtsi? At least it isn't part of torvald's master branch. In any case:
Quoted 6 lines
arch/arm/dts/imx8mq.dtsi +0
-0}; ckil: clock-ckil {Signature · 1 line
2.7.4
PATCH 3/4 arm: imx8mq: Add USB clock init function
In reply to Ye LiAdd clock function to setup relevant clocks for USB3.0 controllers and PHYs on i.MX8MQ
--- arch/arm/include/asm/arch-imx8m/clock.h | 1 + arch/arm/mach-imx/imx8m/clock_imx8mq.c | 22 ++++++++++++++++++++++ 2 files changed, 23 insertions(+)
arch/arm/include/asm/arch-imx8m/clock.h +1 -0
@@ -257,6 +257,7 @@ u32 imx_get_uartclk(void);int clock_init (void );void init_clk_usdhc (u32 index);void init_uart_clk (u32 index); +void init_usb_clk (void );void init_wdog_clk (void );unsigned int mxc_get_clock (enum mxc_clock clk);int clock_enable (enum clk_ccgr_index index,bool enable);
arch/arm/mach-imx/imx8m/clock_imx8mq.c +22 -0
@@ -393,6 +393,28 @@ void init_wdog_clk(void)clock_enable (CCGR_WDOG3 ,1 ); } +void init_usb_clk (void ) +{ +if (!is_usb_boot ()) { +clock_enable (CCGR_USB_CTRL1 ,0 ); +clock_enable (CCGR_USB_CTRL2 ,0 ); +clock_enable (CCGR_USB_PHY1 ,0 ); +clock_enable (CCGR_USB_PHY2 ,0 ); +/* 500MHz */ +clock_set_target_val (USB_BUS_CLK_ROOT ,CLK_ROOT_ON | +CLK_ROOT_SOURCE_SEL (1 )); +/* 100MHz */ +clock_set_target_val (USB_CORE_REF_CLK_ROOT ,CLK_ROOT_ON | +CLK_ROOT_SOURCE_SEL (1 )); +/* 100MHz */ +clock_set_target_val (USB_PHY_REF_CLK_ROOT ,CLK_ROOT_ON | +CLK_ROOT_SOURCE_SEL (1 )); +clock_enable (CCGR_USB_CTRL1 ,1 ); +clock_enable (CCGR_USB_CTRL2 ,1 ); +clock_enable (CCGR_USB_PHY1 ,1 ); +clock_enable (CCGR_USB_PHY2 ,1 ); + } +}void init_nand_clk (void ) {
Signature · 1 line
2.7.4
Re: [PATCH 3/4] arm: imx8mq: Add USB clock init function
Am Sun, Feb 21, 2021 at 08:26:23AM -0800 schrieb Ye Li:
Quoted 4 lines
Add clock function to setup relevant clocks for USB3.0 controllers and PHYs on i.MX8MQ
Signed-off-by Ye Li <[email protected]>
Quoted 53 lines
--- arch/arm/include/asm/arch-imx8m/clock.h | 1 + arch/arm/mach-imx/imx8m/clock_imx8mq.c | 22 ++++++++++++++++++++++ 2 files changed, 23 insertions(+)arch/arm/include/asm/arch-imx8m/clock.h +1
-0@@ -257,6 +257,7 @@ u32 imx_get_uartclk(void);int clock_init (void );void init_clk_usdhc (u32 index);void init_uart_clk (u32 index); +void init_usb_clk (void );void init_wdog_clk (void );unsigned int mxc_get_clock (enum mxc_clock clk);int clock_enable (enum clk_ccgr_index index,bool enable);arch/arm/mach-imx/imx8m/clock_imx8mq.c +22
-0@@ -393,6 +393,28 @@ void init_wdog_clk(void)clock_enable (CCGR_WDOG3 ,1 ); } +void init_usb_clk (void ) +{ +if (!is_usb_boot ()) { +clock_enable (CCGR_USB_CTRL1 ,0 ); +clock_enable (CCGR_USB_CTRL2 ,0 ); +clock_enable (CCGR_USB_PHY1 ,0 ); +clock_enable (CCGR_USB_PHY2 ,0 ); +/* 500MHz */ +clock_set_target_val (USB_BUS_CLK_ROOT ,CLK_ROOT_ON | +CLK_ROOT_SOURCE_SEL (1 )); +/* 100MHz */ +clock_set_target_val (USB_CORE_REF_CLK_ROOT ,CLK_ROOT_ON | +CLK_ROOT_SOURCE_SEL (1 )); +/* 100MHz */ +clock_set_target_val (USB_PHY_REF_CLK_ROOT ,CLK_ROOT_ON | +CLK_ROOT_SOURCE_SEL (1 )); +clock_enable (CCGR_USB_CTRL1 ,1 ); +clock_enable (CCGR_USB_CTRL2 ,1 ); +clock_enable (CCGR_USB_PHY1 ,1 ); +clock_enable (CCGR_USB_PHY2 ,1 ); + } +}void init_nand_clk (void ) {Signature · 1 line
2.7.4
PATCH 4/4 imx8mq_evk: Enable the USB3.0 host port
In reply to Ye LiSetup USB clock in board codes, and enable the DWC3 XHCI and PHY drivers to make USB3.0 host port working on i.MX8MQ EVK.
--- board/freescale/imx8mq_evk/imx8mq_evk.c | 4 ++++ configs/imx8mq_evk_defconfig | 9 +++++++++ 2 files changed, 13 insertions(+)
board/freescale/imx8mq_evk/imx8mq_evk.c +4 -0
@@ -86,6 +86,10 @@ int board_init(void)setup_fec ();#endif +#if defined(CONFIG_USB_DWC3 ) || defined(CONFIG_USB_XHCI_DWC3 ) +init_usb_clk (); +#endif +return 0 ; }
configs/imx8mq_evk_defconfig +9 -0
@@ -54,3 +54,12 @@ CONFIG_DM_REGULATOR_GPIO=y CONFIG_DM_RESET=y CONFIG_MXC_UART=y CONFIG_DM_THERMAL=y +CONFIG_CMD_USB=y +CONFIG_USB=y +CONFIG_USB_STORAGE=y +CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_DWC3=y +CONFIG_PHY=y +CONFIG_PHY_IMX8MQ_USB=y
Signature · 1 line
2.7.4
Fabio Estevam
reviewerPATCH 4/4 imx8mq_evk: Enable the USB3.0 host port
Hi Ye Li,
Quoted 5 lines · Ye Li
Setup USB clock in board codes, and enable the DWC3 XHCI and PHY drivers to make USB3.0 host port working on i.MX8MQ EVK.
Signed-off-by Ye Li <[email protected]>
Thanks for the patch.
Have you tested it in the imx8mq-evk using the latest U-Boot master branch?
The reason I am asking is that imx8mq-evk does not even boot for me unless I apply the following two patches:
https://lists.denx.de/pipermail/u-boot/2021-February/441971.html
https://lists.denx.de/pipermail/u-boot/2021-February/441988.html
Please advise.
[EXT] Re: [PATCH 4/4] imx8mq_evk: Enable the USB3.0 host port
Hi Fabio,
Quoted 35 lines · Fabio Estevam
Caution: EXT Email
Hi Ye Li,
Quoted 6 lines · Ye Li
Setup USB clock in board codes, and enable the DWC3 XHCI and PHY drivers to make USB3.0 host port working on i.MX8MQ EVK.
Signed-off-by Ye Li <[email protected]>Thanks for the patch.
Have you tested it in the imx8mq-evk using the latest U-Boot master branch?
The reason I am asking is that imx8mq-evk does not even boot for me unless I apply the following two patches:
https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Flis
ts.denx.de%2Fpipermail%2Fu-boot%2F2021- February%2F441971.html&data=04%7C01%7Cye.li%40nxp.com%7C16ed6adce 72548e2c57e08d8d97cbf71%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C 637498477099446700%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIj oiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=10PTxobzvXV UaVhn1Rv1yM5xe0uZk3aluha81cPAK%2Fc%3D&reserved=0https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Flis
ts.denx.de%2Fpipermail%2Fu-boot%2F2021- February%2F441988.html&data=04%7C01%7Cye.li%40nxp.com%7C16ed6adce 72548e2c57e08d8d97cbf71%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C 637498477099446700%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIj oiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=lyG6qFbrKVf vMjii3vS5fZ3DQTbxinqms%2FO4D1yX4l4%3D&reserved=0
Quoted 1 line
Please advise.
Sure, I have tested it on 8mq evk. I can reproduce the two issues you met.?
The first issue is caused by the ALIGN. The implementation of standard ALIGN requires the aligned size to be power of 2. But the ALIGN in imx8mimage does not have this requirement. So below result is wrong by using the standard ALIGN. Your fix should be OK for this issue.?
file_off += ALIGN(sbuf.st_size, HDMI_FW_SIZE + 0x2000 + 0x1000);
For the second issue, I did not debug into it. But our vendor tree also uses off-on-delay-us in both u-boot and kernel. So it is likely caused by other change.?
Attach the log of usb host test.
U-Boot SPL 2021.04-rc2-00059-g1784e9b (Feb 21 2021 - 14:35:00 -0800) PMIC:??PFUZE100 ID=0x10
Normal Boot
Trying to boot from MMC2
E/TC:0 0 caam_mp_init:364 ************************************* E/TC:0 0 caam_mp_init:365 * Warning: Manufacturing protection * E/TC:0 0 caam_mp_init:366 *??????????is not supported?????????* E/TC:0 0 caam_mp_init:367 *************************************
U-Boot 2021.04-rc2-00059-g1784e9b (Feb 21 2021 - 14:35:00 -0800)
CPU:???Freescale i.MX8MQ rev2.0 at 1000 MHz
Reset cause: POR
Model: NXP i.MX8MQ EVK
DRAM:??3 GiB
MMC:???FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - No block device, using default environment
In:????serial
Out:???serial
Err:???serial
Net:???eth0: ethernet at 30be0000
Hit any key to stop autoboot:??0
u-boot=> usb start
starting USB...
Bus usb at 38200000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb at 38200000 for devices... cannot reset port 1!? 2 USB Device(s) found
???????scanning usb for storage devices... 1 Storage Device(s) found u-boot=> usb dev
IDE device 0: Vendor: Kingston Rev:??Prod: DataTraveler 3.0 ????????????Type: Removable Hard Disk ????????????Capacity: 14755.2 MB = 14.4 GB (30218842 x 512) u-boot=> usb read 0x40480000 0x0 0x1000
usb read: device 0 block # 0, count 4096 ... 4096 blocks read: OK
Best regards,
Ye Li
Fabio Estevam
reviewer[EXT] Re: [PATCH 4/4] imx8mq_evk: Enable the USB3.0 host port
Hi Ye Li,
Quoted 6 lines · Ye Li
Sure, I have tested it on 8mq evk. I can reproduce the two issues you met.
The first issue is caused by the ALIGN. The implementation of standard ALIGN requires the aligned size to be power of 2. But the ALIGN in imx8mimage does not have this requirement. So below result is wrong by using the standard ALIGN. Your fix should be OK for this issue.
Good, could you please reply to my ALIGN macro patch with your Tested-by tag then?
Quoted 3 lines
For the second issue, I did not debug into it. But our vendor tree also uses off-on-delay-us in both u-boot and kernel. So it is likely caused by other change.
Considering we are already at 2021.04-rc2, I think it would be safer to go with my patch that removes off-on-delay-us.
What do you think?
Thanks
[EXT] Re: [PATCH 4/4] imx8mq_evk: Enable the USB3.0 host port
Hi Fabio,
Quoted 16 lines · Fabio Estevam
Caution: EXT Email
Hi Ye Li,
Quoted 10 lines · Ye Li
Sure, I have tested it on 8mq evk. I can reproduce the two issues you
met.
The first issue is caused by the ALIGN. The implementation of standard
ALIGN requires the aligned size to be power of 2. But the ALIGN in imx8mimage does not have this requirement. So below result is wrong by
using the standard ALIGN. Your fix should be OK for this issue.
Quoted 3 lines
Good, could you please reply to my ALIGN macro patch with your Tested-by tag then?
Replied it.
Quoted 6 lines
Quoted 6 lines
For the second issue, I did not debug into it. But our vendor tree also
uses off-on-delay-us in both u-boot and kernel. So it is likely caused
by other change.
Quoted 6 lines
Considering we are already at 2021.04-rc2, I think it would be safer to go with my patch that removes off-on-delay-us.
What do you think?
Thanks
My debug shows the issue is triggered by below commit:
commit 9098682200e6cca4b776638a51200dafa16f50fb
Author: Haibo Chen <[email protected]>
Date:???Tue Sep 22 18:11:43 2020 +0800
????mmc: fsl_esdhc_imx: remove the 1ms delay before sending command ????
????This 1ms delay before sending command already exist from the beginning
????of the fsl_esdhc driver added in year 2008. Now this driver has been
????split for two files: fsl_esdhc.c and fsl_esdhc_imx.c. fsl_esdhc_imx.c
????only for i.MX series. i.MX series esdhc/usdhc do not need this 1ms delay
????before sending any command. So remove this 1ms, this will save a lot
????time if handling a large mmc data.
????
????Signed-off-by: Haibo Chen <[email protected]>
The first "go idle" command in mmc_get_op_cond seems not put SD card to idle status, but if adding a delay before it (like 1ms delay), then everything works. This commit removed 1ms delay in sending command, so the issue is triggered. ?The root cause might be "startup-delay-us" needed for this regulator to reach a threshold voltage for SD working. Below change also can fix the issue.
arch/arm/dts/imx8mq-evk-u-boot.dtsi +0 -0
@@ -1,6 +1,7 @@
?// SPDX-License-Identifier: (GPL-2.0 OR MIT)
?
?®_usdhc2_vmmc {
+ ? ? ? startup-delay-us = <1000>;
????????u-boot,off-on-delay-us = <20000>;
?};
@Haibo, Could you help looking into the issue. What's your opinion to add the startup-delay-us or revert your commit?
Best regards,
Ye Li
Fabio Estevam
reviewer[EXT] Re: [PATCH 4/4] imx8mq_evk: Enable the USB3.0 host port
Hi Ye Li,
Quoted 1 line · Ye Li
My debug shows the issue is triggered by below commit:
Thanks for investigating this issue. Appreciate it.
Quoted 39 lines
commit
9098682200e6cca4b776638a51200dafa16f50fbAuthor: Haibo Chen <[email protected]> Date: Tue Sep 22 18:11:43 2020 +0800mmc:
fsl_esdhc_imx: remove the 1ms delay before sending commandThis 1ms delay before sending command already exist from the
beginning
of thefsl_esdhcdriver added in year 2008. Now this driver has
been
split for two files:fsl_esdhc.candfsl_esdhc_imx.c.fsl_esdhc_imx.c
only for i.MX series. i.MX series esdhc/usdhc do not need this 1ms
delay
before sending any command. So remove this 1ms, this will save a
lot
time if handling a large mmc data.Signed-off-by Haibo Chen <[email protected]>The first "go idle" command in
mmc_get_op_condseems not put SD card to idle status, but if adding a delay before it (like 1ms delay), then everything works. This commit removed 1ms delay in sending command, so the issue is triggered. The root cause might be "startup-delay-us" needed for this regulator to reach a threshold voltage for SD working. Below change also can fix the issue.arch/arm/dts/imx8mq-evk-u-boot.dtsi +1
-0@@ -1,6 +1,7 @@ // SPDX-License-Identifier: (GPL-2.0 OR MIT) ®_usdhc2_vmmc { + startup-delay-us = <1000>; u-boot,off-on-delay-us = <20000>; };
Quoted 2 lines
@Haibo, Could you help looking into the issue. What's your opinion to add the startup-delay-us or revert your commit?
As the 1ms delay in the driver has been present since 2008, I prefer to go with the revert for the following reasons:
1) We would need to fix all the esdhc users in devicetree.
2) By adding startup-delay-us only to the U-Boot dts we are deviating from the Linux devicetree once again, which we should avoid.
Thanks,
Fabio Estevam
[EXT] Re: [PATCH 4/4] imx8mq_evk: Enable the USB3.0 host port
In reply to Ye LiQuoted 77 lines
-----Original Message-----
From: Ye Li
Sent: 2021?2?27? 14:05
To: festevam at gmail.com; Bough Chen <[email protected]>
Cc: Peng Fan <[email protected]>; u-boot at lists.denx.de; dl-uboot-imx <[email protected]>; sbabic at denx.de
Subject: Re: [EXT] Re: [PATCH 4/4]imx8mq_evk: Enable the USB3.0 host portHi Fabio,
Quoted 14 lines · Fabio Estevam
Caution: EXT Email
Hi Ye Li,
Quoted 8 lines · Ye Li
Sure, I have tested it on 8mq evk. I can reproduce the two issues you met.
The first issue is caused by the ALIGN. The implementation of standard ALIGN requires the aligned size to be power of 2. But the ALIGN in imx8mimage does not have this requirement. So below result is wrong by using the standard ALIGN. Your fix should be OK for this issue.Quoted 3 lines
Good, could you please reply to my ALIGN macro patch with your Tested-by tag then?
Replied it.
Quoted 10 lines
Quoted 4 lines
For the second issue, I did not debug into it. But our vendor tree also uses off-on-delay-us in both u-boot and kernel. So it is likely caused by other change.
Considering we are already at 2021.04-rc2, I think it would be safer to go with my patch that removes off-on-delay-us.
What do you think?
Thanks
My debug shows the issue is triggered by below commit:
commit
9098682200e6cca4b776638a51200dafa16f50fbAuthor: Haibo Chen <[email protected]> Date: Tue Sep 22 18:11:43 2020 +0800mmc:
fsl_esdhc_imx: remove the 1ms delay before sending commandThis 1ms delay before sending command already exist from the beginning of the
fsl_esdhcdriver added in year 2008. Now this driver has been split for two files:fsl_esdhc.candfsl_esdhc_imx.c.fsl_esdhc_imx.c
only for i.MX series. i.MX series esdhc/usdhc do not need this 1ms delay before sending any command. So remove this 1ms, this will save a lot time if handling a large mmc data.Signed-off-by Haibo Chen <[email protected]>The first "go idle" command in
mmc_get_op_condseems not put SD card to idle status, but if adding a delay before it (like 1ms delay), then everything works. This commit removed 1ms delay in sending command, so the issue is triggered. The root cause might be "startup-delay-us"
needed for this regulator to reach a threshold voltage for SD working. Below change also can fix the issue.arch/arm/dts/imx8mq-evk-u-boot.dtsi +1
-0@@ -1,6 +1,7 @@ // SPDX-License-Identifier: (GPL-2.0 OR MIT) ®_usdhc2_vmmc { + startup-delay-us = <1000>; u-boot,off-on-delay-us = <20000>; };
Quoted 3 lines
@Haibo, Could you help looking into the issue. What's your opinion to add the startup-delay-us or revert your commit?
Hi Fabio,
I co-debug with Ye, and find the issue is also related with clock enable/disable. For current logic on imx usdhc, hardware automatically gate off the card clock when idle. So before the first command "go idle", there is no clock on the clock line, which not align with the sd spec.
Refer to SD3.0 spec 6.4.1 Power UP
The host shall supply power to the card so that the voltage is reached to Vdd_min within 250ms and
start to supply at least 74 SD clocks to the SD card with keeping CMD line to high. In case of SPI
mode, CS shall be held to high during 74 clock cycles
if we give the card the correct clock rate before the first "go idle" command, this issue gone.
Please try to apply the patch I send on 2021/1/27 [PATCH] mmc: fsl_esdhc_imx: use VENDORSPEC_FRC_SDCLK_ON to control card clock output
Quoted 2 lines
Best regards,
Ye Li
-------------- next part --------------
A non-text attachment was scrubbed...
Name: smime.p7s
Type: application/pkcs7-signature
Size: 9571 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20210303/0bf8a121/attachment-0001.bin>
Re: [EXT] Re: [PATCH 4/4] imx8mq_evk: Enable the USB3.0 host port
Am Wed, Mar 03, 2021 at 08:53:52AM +0000 schrieb Bough Chen:
Quoted 90 lines
Quoted 77 lines
-----Original Message-----
From: Ye Li
Sent: 2021年2月27日 14:05
To: [email protected]; Bough Chen <[email protected]>
Cc: Peng Fan <[email protected]>; [email protected]; dl-uboot-imx <[email protected]>; [email protected]
Subject: Re: [EXT] Re: [PATCH 4/4]imx8mq_evk: Enable the USB3.0 host portHi Fabio,
Quoted 14 lines · Fabio Estevam
Caution: EXT Email
Hi Ye Li,
Quoted 8 lines · Ye Li
Sure, I have tested it on 8mq evk. I can reproduce the two issues you met.
The first issue is caused by the ALIGN. The implementation of standard ALIGN requires the aligned size to be power of 2. But the ALIGN in imx8mimage does not have this requirement. So below result is wrong by using the standard ALIGN. Your fix should be OK for this issue.Quoted 3 lines
Good, could you please reply to my ALIGN macro patch with your Tested-by tag then?
Replied it.
Quoted 10 lines
Quoted 4 lines
For the second issue, I did not debug into it. But our vendor tree also uses off-on-delay-us in both u-boot and kernel. So it is likely caused by other change.
Considering we are already at 2021.04-rc2, I think it would be safer to go with my patch that removes off-on-delay-us.
What do you think?
Thanks
My debug shows the issue is triggered by below commit:
commit
9098682200e6cca4b776638a51200dafa16f50fbAuthor: Haibo Chen <[email protected]> Date: Tue Sep 22 18:11:43 2020 +0800mmc:
fsl_esdhc_imx: remove the 1ms delay before sending commandThis 1ms delay before sending command already exist from the beginning of the
fsl_esdhcdriver added in year 2008. Now this driver has been split for two files:fsl_esdhc.candfsl_esdhc_imx.c.fsl_esdhc_imx.c
only for i.MX series. i.MX series esdhc/usdhc do not need this 1ms delay before sending any command. So remove this 1ms, this will save a lot time if handling a large mmc data.Signed-off-by Haibo Chen <[email protected]>The first "go idle" command in
mmc_get_op_condseems not put SD card to idle status, but if adding a delay before it (like 1ms delay), then everything works. This commit removed 1ms delay in sending command, so the issue is triggered. The root cause might be "startup-delay-us"
needed for this regulator to reach a threshold voltage for SD working. Below change also can fix the issue.arch/arm/dts/imx8mq-evk-u-boot.dtsi +1
-0@@ -1,6 +1,7 @@ // SPDX-License-Identifier: (GPL-2.0 OR MIT) ®_usdhc2_vmmc { + startup-delay-us = <1000>; u-boot,off-on-delay-us = <20000>; };Quoted 3 lines
@Haibo, Could you help looking into the issue. What's your opinion to add the startup-delay-us or revert your commit?
Hi Fabio,
I co-debug with Ye, and find the issue is also related with clock enable/disable. For current logic on imx usdhc, hardware automatically gate off the card clock when idle. So before the first command "go idle", there is no clock on the clock line, which not align with the sd spec.
Refer to SD3.0 spec 6.4.1 Power UP
The host shall supply power to the card so that the voltage is reached toVdd_minwithin 250ms and
start to supply at least 74 SD clocks to the SD card with keeping CMD line to high. In case of SPI
mode, CS shall be held to high during 74 clock cycles
Quoted 5 lines
if we give the card the correct clock rate before the first "go idle" command, this issue gone.
Please try to apply the patch I send on 2021/1/27 [PATCH] mmc:fsl_esdhc_imx: useVENDORSPEC_FRC_SDCLK_ONto control card clock outputQuoted 2 lines
Best regards,
Ye Li
Hi,
is this patchset still being reviewed? I think the discussion has moved to some SD card problem, which is fixed now? Would be nice if USB 3.0 worked on i.MX8MQ platforms.
I can also have a look at reviewing the functionality, but I don't think I can spot U-Boot coding style issues.
Best regards,
Patrick
Fabio Estevam
reviewerRe: [EXT] Re: [PATCH 4/4] imx8mq_evk: Enable the USB3.0 host port
Hi Patrick,
Quoted 2 lines · Patrick Wildt
is this patchset still being reviewed? I think the discussion has moved to some SD card problem, which is fixed now? Would be nice if USB 3.0
I think you are referring to
https://source.denx.de/u-boot/u-boot/-/commit/63756575b42b8b4fb3f59cbbf0cedf03331bc2d2
If so, I had to revert it as it caused boot time regression (10s in SPL + 10 s in U-Boot proper) in several
i.MX boards:
https://source.denx.de/u-boot/u-boot/-/commit/f132aab403271ff00c0cfdd3af6504e87c7d0aaf
I haven't tested USB 3.0 in mainline U-Boot on imx8mq-evk. Maybe Peng or Ye Li can comment.
Regards,
Fabio Estevam
Quoted 7 lines
worked on i.MX8MQ platforms.
I can also have a look at reviewing the functionality, but I don't think I can spot U-Boot coding style issues.
Best regards,
Patrick
Re: [EXT] Re: [PATCH 4/4] imx8mq_evk: Enable the USB3.0 host port
Am Mon, Jul 12, 2021 at 10:28:25AM -0300 schrieb Fabio Estevam:
Quoted 10 lines
Hi Patrick,
Quoted 2 lines · Patrick Wildt
is this patchset still being reviewed? I think the discussion has moved to some SD card problem, which is fixed now? Would be nice if USB 3.0
I think you are referring to
https://source.denx.de/u-boot/u-boot/-/commit/63756575b42b8b4fb3f59cbbf0cedf03331bc2d2
Quoted 8 lines
If so, I had to revert it as it caused boot time regression (10s in SPL + 10 s in U-Boot proper) in several
i.MX boards:https://source.denx.de/u-boot/u-boot/-/commit/f132aab403271ff00c0cfdd3af6504e87c7d0aaf
I haven't tested USB 3.0 in mainline U-Boot on imx8mq-evk. Maybe Peng or Ye Li can comment.
Hi Fabio,
I cherry-picked this USB 3.0 series from Ye Ling on to the MNT Reform2 patchset I sent out, and I'm happy with the results.
Best regards,
Patrick
Re: [PATCH 4/4] imx8mq_evk: Enable the USB3.0 host port
In reply to Ye LiAm Sun, Feb 21, 2021 at 08:26:24AM -0800 schrieb Ye Li:
Quoted 4 lines
Setup USB clock in board codes, and enable the DWC3 XHCI and PHY drivers to make USB3.0 host port working on i.MX8MQ EVK.
Signed-off-by Ye Li <[email protected]>
The same change works on the MNT Reform 2 as well.
Quoted 39 lines
board/freescale/imx8mq_evk/imx8mq_evk.c | 4 ++++ configs/imx8mq_evk_defconfig | 9 +++++++++ 2 files changed, 13 insertions(+)board/freescale/imx8mq_evk/imx8mq_evk.c +4
-0@@ -86,6 +86,10 @@ int board_init(void)setup_fec ();#endif +#if defined(CONFIG_USB_DWC3 ) || defined(CONFIG_USB_XHCI_DWC3 ) +init_usb_clk (); +#endif +return 0 ; }configs/imx8mq_evk_defconfig +9
-0@@ -54,3 +54,12 @@ CONFIG_DM_REGULATOR_GPIO=y CONFIG_DM_RESET=y CONFIG_MXC_UART=y CONFIG_DM_THERMAL=y +CONFIG_CMD_USB=y +CONFIG_USB=y +CONFIG_USB_STORAGE=y +CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_DWC3=y +CONFIG_PHY=y +CONFIG_PHY_IMX8MQ_USB=ySignature · 1 line
2.7.4
Am Sun, Feb 21, 2021 at 08:26:21AM -0800 schrieb Ye Li:
Quoted 3 lines
Add the USB PHY driver for i.MX8MQ to work with DWC3 USB controller.
Signed-off-by Ye Li <[email protected]>
Quoted 239 lines
--- drivers/phy/Kconfig | 7 ++ drivers/phy/Makefile | 1 + drivers/phy/phy-imx8mq-usb.c | 197 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 205 insertions(+) create mode 100644 drivers/phy/phy-imx8mq-usb.cdrivers/phy/Kconfig +7
-0@@ -268,5 +268,12 @@ config PHY_MTK_TPHY multi-ports is first version, otherwise is second veriosn, so you can easily distinguish them by banks layout. +config PHY_IMX8MQ_USB + bool "NXP i.MX8MQ USB PHY Driver" + depends on PHY + depends on IMX8MQ + help + Support the USB3.0 PHY in NXP i.MX8MQ SoC + source "drivers/phy/rockchip/Kconfig" endmenudrivers/phy/Makefile +1
-0@@ -31,3 +31,4 @@ obj-$(CONFIG_MT7620_USB_PHY) += mt7620-usb-phy.o obj-$(CONFIG_MT76X8_USB_PHY) += mt76x8-usb-phy.o obj-$(CONFIG_PHY_DA8XX_USB) += phy-da8xx-usb.o obj-$(CONFIG_PHY_MTK_TPHY) += phy-mtk-tphy.o +obj-$(CONFIG_PHY_IMX8MQ_USB) += phy-imx8mq-usb.odrivers/phy/phy-imx8mq-usb.c new file +197
-0@@ -0,0 +1,197 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright 2021 NXP +* +*/ + +#include <common.h> +#include <asm/io.h> +#include <dm.h> +#include <errno.h> +#include <generic-phy.h> +#include <linux/bitops.h> +#include <linux/err.h> +#include <clk.h> + +#define PHY_CTRL0 0x0 +#define PHY_CTRL0_REF_SSP_EN BIT(2) +#define PHY_CTRL0_FSEL_MASK GENMASK(10, 5) +#define PHY_CTRL0_FSEL_24M 0x2a +#define PHY_CTRL0_FSEL_100M 0x27 +#define PHY_CTRL0_SSC_RANGE_MASK GENMASK(23, 21) +#define PHY_CTRL0_SSC_RANGE_4003PPM (0x2 << 21) + +#define PHY_CTRL1 0x4 +#define PHY_CTRL1_RESET BIT(0) +#define PHY_CTRL1_COMMONONN BIT(1) +#define PHY_CTRL1_ATERESET BIT(3) +#define PHY_CTRL1_DCDENB BIT(17) +#define PHY_CTRL1_CHRGSEL BIT(18) +#define PHY_CTRL1_VDATSRCENB0 BIT(19) +#define PHY_CTRL1_VDATDETENB0 BIT(20) + +#define PHY_CTRL2 0x8 +#define PHY_CTRL2_TXENABLEN0 BIT(8) +#define PHY_CTRL2_OTG_DISABLE BIT(9) + +#define PHY_CTRL3 0xc +#define PHY_CTRL3_COMPDISTUNE_MASK GENMASK(2, 0) +#define PHY_CTRL3_TXPREEMP_TUNE_MASK GENMASK(16, 15) +#define PHY_CTRL3_TXPREEMP_TUNE_SHIFT 15 +#define PHY_CTRL3_TXRISE_TUNE_MASK GENMASK(21, 20) +#define PHY_CTRL3_TXRISE_TUNE_SHIFT 20 +/* 1111: +24% ... 0000: -6% step: 2% */ +#define PHY_CTRL3_TXVREF_TUNE_MASK GENMASK(25, 22) +#define PHY_CTRL3_TXVREF_TUNE_SHIFT 22 +#define PHY_CTRL3_TX_VBOOST_LEVEL_MASK GENMASK(31, 29) +#define PHY_CTRL3_TX_VBOOST_LEVEL_SHIFT 29 + +#define PHY_CTRL4 0x10 +#define PHY_CTRL4_PCS_TX_DEEMPH_3P5DB_MASK GENMASK(20, 15) +#define PHY_CTRL4_PCS_TX_DEEMPH_3P5DB_SHIFT 15 + +#define PHY_CTRL5 0x14 +#define PHY_CTRL5_DMPWD_OVERRIDE_SEL BIT(23) +#define PHY_CTRL5_DMPWD_OVERRIDE BIT(22) +#define PHY_CTRL5_DPPWD_OVERRIDE_SEL BIT(21) +#define PHY_CTRL5_DPPWD_OVERRIDE BIT(20) +#define PHY_CTRL5_PCS_TX_SWING_FULL_MASK GENMASK(6, 0) + +#define PHY_CTRL6 0x18 +#define PHY_CTRL6_RXTERM_OVERRIDE_SEL BIT(29) +#define PHY_CTRL6_ALT_CLK_EN BIT(1) +#define PHY_CTRL6_ALT_CLK_SEL BIT(0) + +#define PHY_STS0 0x40 +#define PHY_STS0_OTGSESSVLD BIT(7) +#define PHY_STS0_CHGDET BIT(4) +#define PHY_STS0_FSVPLUS BIT(3) +#define PHY_STS0_FSVMINUS BIT(2) + +struct imx8mq_usb_phy { +#if CONFIG_IS_ENABLED (CLK ) +struct clk phy_clk; +#endif +void __iomem *base; +}; + +static const struct udevice_id imx8mq_usb_phy_of_match[] = { + { + .compatible ="fsl,imx8mq-usb-phy" , + }, + {}, +}; + +static int imx8mq_usb_phy_init (struct phy *usb_phy) +{ +struct udevice *dev = usb_phy->dev; +struct imx8mq_usb_phy *imx_phy =dev_get_priv (dev); +u32 value; + + value =readl (imx_phy->base +PHY_CTRL1 ); + value &= ~(PHY_CTRL1_VDATSRCENB0 |PHY_CTRL1_VDATDETENB0 | +PHY_CTRL1_COMMONONN ); + value |=PHY_CTRL1_RESET |PHY_CTRL1_ATERESET ; +writel (value, imx_phy->base +PHY_CTRL1 ); + + value =readl (imx_phy->base +PHY_CTRL0 ); + value |=PHY_CTRL0_REF_SSP_EN ; + value &= ~PHY_CTRL0_SSC_RANGE_MASK ; + value |=PHY_CTRL0_SSC_RANGE_4003PPM ; +writel (value, imx_phy->base +PHY_CTRL0 ); + + value =readl (imx_phy->base +PHY_CTRL2 ); + value |=PHY_CTRL2_TXENABLEN0 ; +writel (value, imx_phy->base +PHY_CTRL2 ); + + value =readl (imx_phy->base +PHY_CTRL1 ); + value &= ~(PHY_CTRL1_RESET |PHY_CTRL1_ATERESET ); +writel (value, imx_phy->base +PHY_CTRL1 ); + +return 0 ; +} + +static int imx8mq_usb_phy_power_on (struct phy *usb_phy) +{ +struct udevice *dev = usb_phy->dev; +struct imx8mq_usb_phy *imx_phy =dev_get_priv (dev); +u32 value; + +#if CONFIG_IS_ENABLED (CLK ) +int ret; + ret =clk_enable (&imx_phy->phy_clk); +if (ret) { +printf ("Failed to enable usb phy clock\n" ); +return ret; + } +#endif + +/* Disable rx term override */ + value =readl (imx_phy->base +PHY_CTRL6 ); + value &= ~PHY_CTRL6_RXTERM_OVERRIDE_SEL ; +writel (value, imx_phy->base +PHY_CTRL6 ); + +return 0 ; +} + +static int imx8mq_usb_phy_power_off (struct phy *usb_phy) +{ +struct udevice *dev = usb_phy->dev; +struct imx8mq_usb_phy *imx_phy =dev_get_priv (dev); +u32 value; + +/* Override rx term to be 0 */ + value =readl (imx_phy->base +PHY_CTRL6 ); + value |=PHY_CTRL6_RXTERM_OVERRIDE_SEL ; +writel (value, imx_phy->base +PHY_CTRL6 ); + +#if CONFIG_IS_ENABLED (CLK ) +clk_disable (&imx_phy->phy_clk); +#endif + +return 0 ; +} + +static int imx8mq_usb_phy_exit (struct phy *usb_phy) +{ +return imx8mq_usb_phy_power_off (usb_phy); +} + +struct phy_ops imx8mq_usb_phy_ops = { + .init = imx8mq_usb_phy_init, + .power_on = imx8mq_usb_phy_power_on, + .power_off = imx8mq_usb_phy_power_off, + .exit = imx8mq_usb_phy_exit, +}; + +int imx8mq_usb_phy_probe (struct udevice *dev) +{ +struct imx8mq_usb_phy *priv =dev_get_priv (dev); + + priv->base =dev_read_addr_ptr (dev); + +if (!priv->base) +return -EINVAL ; + +#if CONFIG_IS_ENABLED (CLK ) +int ret; + +/* Assigned clock already set clock */ + ret =clk_get_by_name (dev,"phy" , &priv->phy_clk); +if (ret) { +printf ("Failed to get usb phy clock\n" ); +return ret; + } +#endif + +return 0 ; +} + +U_BOOT_DRIVER (nxp_imx8mq_usb_phy) = { + .name ="nxp_imx8mq_usb_phy" , + .id =UCLASS_PHY , + .of_match = imx8mq_usb_phy_of_match, + .probe = imx8mq_usb_phy_probe, + .ops = &imx8mq_usb_phy_ops, + .priv_auto =sizeof (struct imx8mq_usb_phy ), +};Signature · 1 line
2.7.4
Fabio Estevam
reviewerHi Patrick,
Quoted 8 lines · Patrick Wildt
Am Sun, Feb 21, 2021 at 08:26:21AM -0800 schrieb Ye Li:
Quoted 3 lines
Add the USB PHY driver for i.MX8MQ to work with DWC3 USB controller.
Signed-off-by Ye Li <[email protected]>Reviewed-by Patrick Wildt <[email protected]>Tested-by Patrick Wildt <[email protected]>
It seems Ye Li missed adding Marek on Cc.
Could you please resend the series with Marek on Cc?
Thanks
Hi Fabio,
Quoted 7 lines · Fabio Estevam
Hi Patrick,
Quoted 4 lines · Patrick Wildt
Am Sun, Feb 21, 2021 at 08:26:21AM -0800 schrieb Ye Li:
Quoted 2 lines
Add the USB PHY driver for i.MX8MQ to work with DWC3 USB controller.
Quoted 9 lines
Quoted 4 lines
Quoted 1 line
Signed-off-by Ye Li <[email protected]>Reviewed-by Patrick Wildt <[email protected]>Tested-by Patrick Wildt <[email protected]>It seems Ye Li missed adding Marek on Cc.
Could you please resend the series with Marek on Cc?
I see that the series is already assigned to Marek:
http://patchwork.ozlabs.org/project/uboot/list/?series=230965
So I guess it is enough to inform Marek (in CC) about this and he can review / apply the patches without reposting.
Regards,
Stefano
Quoted 2 lines
Thanks
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
Quoted 17 lines · Stefano Babic
Hi Fabio,
Quoted 14 lines · Fabio Estevam
Hi Patrick,
Quoted 8 lines · Patrick Wildt
Am Sun, Feb 21, 2021 at 08:26:21AM -0800 schrieb Ye Li:
Quoted 3 lines
Add the USB PHY driver for i.MX8MQ to work with DWC3 USB controller.
Signed-off-by Ye Li <[email protected]>Reviewed-by Patrick Wildt <[email protected]>Tested-by Patrick Wildt <[email protected]>It seems Ye Li missed adding Marek on Cc.
Quoted 8 lines
Quoted 2 lines
Could you please resend the series with Marek on Cc?
I see that the series is already assigned to Marek:
http://patchwork.ozlabs.org/project/uboot/list/?series=230965
So I guess it is enough to inform Marek (in CC) about this and he can review / apply the patches without reposting.
USB3 is Bin.
Quoted 21 lines · Marek Vasut
Quoted 20 lines · Stefano Babic
Hi Fabio,
Quoted 16 lines · Fabio Estevam
Hi Patrick,
Quoted 8 lines · Patrick Wildt
Am Sun, Feb 21, 2021 at 08:26:21AM -0800 schrieb Ye Li:
Quoted 3 lines
Add the USB PHY driver for i.MX8MQ to work with DWC3 USB controller.
Signed-off-by Ye Li <[email protected]>Reviewed-by Patrick Wildt <[email protected]>Tested-by Patrick Wildt <[email protected]>It seems Ye Li missed adding Marek on Cc.
Could you please resend the series with Marek on Cc?
Quoted 7 lines
Quoted 5 lines
I see that the series is already assigned to Marek:
http://patchwork.ozlabs.org/project/uboot/list/?series=230965
So I guess it is enough to inform Marek (in CC) about this and he can review / apply the patches without reposting.
USB3 is Bin.
Then delegate on patchwork is wrong as the patches are assigned to you.
Regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
Am Tue, Jul 13, 2021 at 12:46:04PM +0200 schrieb Stefano Babic:
Quoted 25 lines · Marek Vasut
Quoted 24 lines · Stefano Babic
Quoted 23 lines
Hi Fabio,
Quoted 8 lines · Fabio Estevam
Hi Patrick,
Quoted 4 lines · Patrick Wildt
Am Sun, Feb 21, 2021 at 08:26:21AM -0800 schrieb Ye Li:
Quoted 2 lines
Add the USB PHY driver for i.MX8MQ to work with DWC3 USB controller.
Quoted 9 lines
Quoted 4 lines
Quoted 1 line
Signed-off-by Ye Li <[email protected]>Reviewed-by Patrick Wildt <[email protected]>Tested-by Patrick Wildt <[email protected]>It seems Ye Li missed adding Marek on Cc.
Could you please resend the series with Marek on Cc?
I see that the series is already assigned to Marek:
Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
http://patchwork.ozlabs.org/project/uboot/list/?series=230965
So I guess it is enough to inform Marek (in CC) about this and he can review / apply the patches without reposting.
USB3 is Bin.
Then delegate on patchwork is wrong as the patches are assigned to you.
The patches contain a new PHY driver, i.MX8MQ clock init code and device tree change. So it's not really USB, it's just some work in the i.MX8MQ stuff to *enable* USB.
Quoted 31 lines · Patrick Wildt
Am Tue, Jul 13, 2021 at 12:46:04PM +0200 schrieb Stefano Babic:
Quoted 30 lines · Marek Vasut
Quoted 29 lines · Stefano Babic
Quoted 27 lines
Hi Fabio,
Quoted 8 lines · Fabio Estevam
Hi Patrick,
Quoted 4 lines · Patrick Wildt
Am Sun, Feb 21, 2021 at 08:26:21AM -0800 schrieb Ye Li:
Quoted 2 lines
Add the USB PHY driver for i.MX8MQ to work with DWC3 USB controller.
Quoted 9 lines
Quoted 4 lines
Quoted 1 line
Signed-off-by Ye Li <[email protected]>Reviewed-by Patrick Wildt <[email protected]>Tested-by Patrick Wildt <[email protected]>It seems Ye Li missed adding Marek on Cc.
Could you please resend the series with Marek on Cc?
I see that the series is already assigned to Marek:
http://patchwork.ozlabs.org/project/uboot/list/?series=230965
So I guess it is enough to inform Marek (in CC) about this and he can review / apply the patches without reposting.
Quoted 7 lines
Quoted 3 lines
Quoted 1 line
USB3 is Bin.
Then delegate on patchwork is wrong as the patches are assigned to you.
The patches contain a new PHY driver, i.MX8MQ clock init code and device tree change. So it's not really USB, it's just some work in the i.MX8MQ stuff to *enable* USB.
Then just lets have Stefano pick it all, since its imx anyway, and be done with it.
Quoted 34 lines · Marek Vasut
Quoted 33 lines · Patrick Wildt
Am Tue, Jul 13, 2021 at 12:46:04PM +0200 schrieb Stefano Babic:
Quoted 32 lines · Marek Vasut
Quoted 30 lines · Stefano Babic
Quoted 21 lines
Hi Fabio,
Quoted 8 lines · Fabio Estevam
Hi Patrick,
Quoted 4 lines · Patrick Wildt
Am Sun, Feb 21, 2021 at 08:26:21AM -0800 schrieb Ye Li:
Quoted 2 lines
Add the USB PHY driver for i.MX8MQ to work with DWC3 USB controller.
Quoted 9 lines
Quoted 4 lines
Quoted 1 line
Signed-off-by Ye Li <[email protected]>Reviewed-by Patrick Wildt <[email protected]>Tested-by Patrick Wildt <[email protected]>It seems Ye Li missed adding Marek on Cc.
Could you please resend the series with Marek on Cc?
Quoted 6 lines
I see that the series is already assigned to Marek:
http://patchwork.ozlabs.org/project/uboot/list/?series=230965
So I guess it is enough to inform Marek (in CC) about this and he can review / apply the patches without reposting.
USB3 is Bin.
Quoted 7 lines
Quoted 5 lines
Quoted 1 line
Then delegate on patchwork is wrong as the patches are assigned to you.
The patches contain a new PHY driver, i.MX8MQ clock init code and device tree change. So it's not really USB, it's just some work in the i.MX8MQ stuff to *enable* USB.
Then just lets have Stefano pick it all, since its imx anyway, and be done with it.
Right, it looks like I took advantage that patches were not assigned to me and I have simply ignored...
I set myself as delegate and I will pick them up.
Regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================