arm64: synquacer: Add SynQuacer/DeveloperBox support
Subsystems (8)
v4 cover arm64: synquacer: Add SynQuacer/DeveloperBox support
Hi,
Here is the 4th version of the series (including some fixes for build errors) to add SynQuacer/DeveloperBox 96board EE suport on U-Boot.
This series includes not only DeveloperBox support but also some fixes for the issues which I faced while porting U-Boot on the DeveloperBox. First 3 patches are fixes, next 1 patch is a code cleanup for generic gpio for arm. The next 7 patches adding DeveloperBox devices and board support. The last 3 patches are related to the UEFI capsule update (including bugfixes).
Previous version is here:
https://lists.denx.de/pipermail/u-boot/2021-May/449305.html
Changes in v4
-------------
I dropped a PCI bugfix because it has been merged. And add I2C driver and enable RTC and EBBR support on the configuration.
[06/14]:
- Add Jaehoon's reviewed-by (Thanks!)
[09/14]:
- Add a new i2c driver.
[10/14]:
- Add i2c0 and RTC node.
[11/14]:
- Add I2C and RTC configuration.
- Enable RTC and Date command.
- Remove I2C0 node before booting linux to hide it same as EDK2 does.
- Add some configurations to make it EBBR compliant.
[14/14]:
- Add some config options for EBBR.
BTW, should I split fixes from this series? (since I didn't expect this took so long...)
DeveloperBox
============
DeveloperBox is a certified 96boards Enterprise Edition board. The board/SoC has: -
* Socionext SC2A11 24-cores ARM Cortex-A53 on tbe Mini-ATX form factor motherboard
* 4 DIMM slots (4GB DDR4-2400 UDIMM shipped by default)
* 1 4xPCIe Gen2 slot and 2 1xPCIe Gen2 slots
(1x slots are connected via PCIe bridge chip)
* 4 USB-3.0 ports
* 2 SATA ports
* 1 GbE network port
* 1 USB-UART serial port (micro USB)
* 64MB SPI NOR Flash
* 8GB eMMC Flash Storage
* 96boards LS connector
The DeveloperBox schematic can be found here: -
https://www.96boards.org/documentation/enterprise/developerbox/hardware-docs/mzsc2am_v03_20180115_a.pdf
And the other documents can be found here: -
https://www.96boards.org/documentation/enterprise/developerbox/
Currently, the U-Boot port supports: -
* USB
* eMMC
* SPI-NOR
* SATA
* GbE
The DeveloperBox boots the TF-A and EDK2 as a main bootloader by default. The DeveloperBox U-Boot port will replace the EDK2 and boot from TF-A as BL33, but no need to combine with it.
Thank you,
---
Jassi Brar (4):
mmc: synquacer: Add SynQuacer F_SDH30 SDHCI driver
spi: synquacer: Add HSSPI SPI controller driver for SynQuacer
net: synquacer: Add netsec driver
i2c: synquacer: SNI Synquacer I2C controller
Masami Hiramatsu (10):
ata: ahci-pci: Use scsi_ops to initialize ops
dm: pci: Skip setting VGA bridge bits if parent device is the host bus
efi: Fix to use null handle to create new handle for efi_fmp_raw
gpio: Introduce CONFIG_GPIO_EXTRA_HEADER to cleanup #ifdefs
pci: synquacer: Add SynQuacer ECAM based PCIe driver
ARM: dts: synquacer: Add device trees for DeveloperBox
board: synquacer: Add DeveloperBox 96boards EE support
dfu_mtd: Ignore non-implemented lock device failure
doc: qemu: arm64: Fix the documentation of capsule update
configs: synquacer: Enable EFI capsule update support
arch/arm/Kconfig | 108 ++ arch/arm/dts/Makefile | 2 arch/arm/dts/synquacer-sc2a11-caches.dtsi | 73 + .../dts/synquacer-sc2a11-developerbox-u-boot.dtsi | 75 + arch/arm/dts/synquacer-sc2a11-developerbox.dts | 56 + arch/arm/dts/synquacer-sc2a11.dtsi | 595 ++++++++++ arch/arm/include/asm/gpio.h | 8 board/socionext/developerbox/Kconfig | 36 + board/socionext/developerbox/MAINTAINERS | 14 board/socionext/developerbox/Makefile | 9 board/socionext/developerbox/developerbox.c | 146 +++ configs/synquacer_developerbox_defconfig | 131 ++ doc/board/emulation/qemu_capsule_update.rst | 11 doc/board/index.rst | 1 doc/board/socionext/developerbox.rst | 87 ++ doc/board/socionext/index.rst | 9 drivers/ata/ahci-pci.c | 2 drivers/dfu/dfu_mtd.c | 2 drivers/i2c/Kconfig | 7 drivers/i2c/Makefile | 1 drivers/i2c/synquacer_i2c.c | 338 ++++++ drivers/mmc/Kconfig | 10 drivers/mmc/Makefile | 1 drivers/mmc/f_sdh30.c | 81 + drivers/net/Kconfig | 8 drivers/net/Makefile | 1 drivers/net/sni_netsec.c | 1134 ++++++++++++++++++++ drivers/pci/Kconfig | 12 drivers/pci/Makefile | 1 drivers/pci/pci-uclass.c | 3 drivers/pci/pcie_ecam_synquacer.c | 600 +++++++++++ drivers/spi/Kconfig | 8 drivers/spi/Makefile | 1 drivers/spi/spi-synquacer.c | 491 +++++++++ include/configs/synquacer.h | 115 ++ lib/efi_loader/efi_capsule.c | 2 36 files changed, 4162 insertions(+), 17 deletions(-) create mode 100644 arch/arm/dts/synquacer-sc2a11-caches.dtsi create mode 100644 arch/arm/dts/synquacer-sc2a11-developerbox-u-boot.dtsi create mode 100644 arch/arm/dts/synquacer-sc2a11-developerbox.dts create mode 100644 arch/arm/dts/synquacer-sc2a11.dtsi create mode 100644 board/socionext/developerbox/Kconfig create mode 100644 board/socionext/developerbox/MAINTAINERS create mode 100644 board/socionext/developerbox/Makefile create mode 100644 board/socionext/developerbox/developerbox.c create mode 100644 configs/synquacer_developerbox_defconfig create mode 100644 doc/board/socionext/developerbox.rst create mode 100644 doc/board/socionext/index.rst create mode 100644 drivers/i2c/synquacer_i2c.c create mode 100644 drivers/mmc/f_sdh30.c create mode 100644 drivers/net/sni_netsec.c create mode 100644 drivers/pci/pcie_ecam_synquacer.c create mode 100644 drivers/spi/spi-synquacer.c create mode 100644 include/configs/synquacer.h
--
Masami Hiramatsu <[email protected]>
PATCH v4 1/14 ata: ahci-pci: Use scsi_ops to initialize ops
Without this fix, scsi-scan will cause a synchronous abort when accessing ops->scan.
--- drivers/ata/ahci-pci.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/ata/ahci-pci.c +2 -0
@@ -5,6 +5,7 @@#include <common.h> #include <ahci.h> +#include <scsi.h> #include <dm.h> #include <pci.h>
@@ -28,6 +29,7 @@ static const struct udevice_id ahci_pci_ids[] = {U_BOOT_DRIVER (ahci_pci) = { .name ="ahci_pci" , .id =UCLASS_AHCI , + .ops = &scsi_ops, .of_match = ahci_pci_ids, .bind = ahci_pci_bind, .probe = ahci_pci_probe,
PATCH v4 2/14 dm: pci: Skip setting VGA bridge bits if parent device is the host bus
In reply to Masami HiramatsuCommit bbbcb5262839 ("dm: pci: Enable VGA address forwarding on bridges") sets the VGA bridge bits by checking pplat->class, but if the parent device is the pci host bus device, it can be skipped. Moreover, it shouldn't access the pplat because the parent has different plat data.
Without this fix, "pci enum" command cause a synchronous abort.
pci_auto_config_devices: start
PCI Autoconfig: Bus Memory region: [78000000-7fffffff],
Physical Memory [78000000-7fffffffx] PCI Autoconfig: Bus I/O region: [0-ffff], Physical Memory [77f00000-77f0ffffx]
pci_auto_config_devices: device pci_6:0.0
PCI Autoconfig: BAR 0, Mem, size=0x1000000, address=0x78000000 bus_lower=0x79000000
PCI Autoconfig: BAR 1, Mem, size=0x8000000, No room in resource, avail start=79000000 / size=8000000, need=8000000
PCI: Failed autoconfig bar 14
PCI Autoconfig: BAR 2, I/O, size=0x4, address=0x1000 bus_lower=0x1004
PCI Autoconfig: BAR 3, Mem, size=0x2000000, address=0x7a000000 bus_lower=0x7c000000
PCI Autoconfig: BAR 4, I/O, size=0x80, address=0x1080 bus_lower=0x1100
PCI Autoconfig: ROM, size=0x80000, address=0x7c000000 bus_lower=0x7c080000
"Synchronous Abort" handler, esr 0x96000006
elr: 00000000e002bd28 lr : 00000000e002bce8 (reloc)
elr: 00000000fff6fd28 lr : 00000000fff6fce8 x0 : 0000000000001041 x1 : 000000000000003e x2 : 00000000ffb0f8c8 x3 : 0000000000000001 x4 : 0000000000000080 x5 : 0000000000000000 x6 : 00000000fff718fc x7 : 000000000000000f x8 : 00000000ffb0f238 x9 : 0000000000000008
x10: 0000000000000000 x11: 0000000000000010
x12: 0000000000000006 x13: 000000000001869f
x14: 00000000ffb0fcd0 x15: 0000000000000020
x16: 00000000fff71cc4 x17: 0000000000000000
x18: 00000000ffb13d90 x19: 00000000ffb14320
x20: 0000000000000000 x21: 00000000ffb14090
x22: 00000000ffb0f8c8 x23: 0000000000000001
x24: 00000000ffb14c10 x25: 0000000000000000
x26: 0000000000000000 x27: 0000000000000000
x28: 00000000ffb14c70 x29: 00000000ffb0f830
Code: 52800843 52800061 52800e00 97ffcf65 (b9400280)
Resetting CPU ...
--- drivers/pci/pci-uclass.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/pci/pci-uclass.c +3 -0
@@ -550,6 +550,9 @@ int pci_auto_config_devices(struct udevice *bus) max_bus = ret; sub_bus =max (sub_bus, max_bus); +if (dev_get_parent (dev) == bus) +continue ; + pplat =dev_get_parent_plat (dev);if (pplat->class == (PCI_CLASS_DISPLAY_VGA <<8 ))set_vga_bridge_bits (dev);
PATCH v4 3/14 efi: Fix to use null handle to create new handle for efi_fmp_raw
In reply to Masami HiramatsuWhen running the efidebug capsule disk-update command, the efi_fmp_raw protocol installation is failed with 2 (EFI_INVALID_PARAMETER) as below. This is because the code passes efi_root instaed of handle.
=> efidebug capsule disk-update
EFI: Call: efi_install_multiple_protocol_interfaces( &handle, &efi_guid_firmware_management_protocol, &efi_fmp_fit, NULL)
EFI: Entry efi_install_multiple_protocol_interfaces(00000000fbaf5988)
EFI: Call: efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface)
EFI: Entry efi_install_protocol_interface(00000000fbaf5988, 86c77a67-0b97-4633-a187-49104d0685c7, 0, 00000000fbfa6ee8)
EFI: new handle 00000000fbb37520
EFI: Exit: efi_install_protocol_interface: 0
EFI: 0 returned by efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface)
EFI: Exit: efi_install_multiple_protocol_interfaces: 0
EFI: 0 returned by efi_install_multiple_protocol_interfaces( &handle, &efi_guid_firmware_management_protocol, &efi_fmp_fit, NULL)
EFI: Call: efi_install_multiple_protocol_interfaces( &efi_root, &efi_guid_firmware_management_protocol, &efi_fmp_raw, NULL)
EFI: Entry efi_install_multiple_protocol_interfaces(00000000fbfec648)
EFI: Call: efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface)
EFI: Entry efi_install_protocol_interface(00000000fbfec648, 86c77a67-0b97-4633-a187-49104d0685c7, 0, 00000000fbfa6f18)
EFI: handle 00000000fbaf8520
EFI: Exit: efi_install_protocol_interface: 2
EFI: 2 returned by efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface)
EFI: Exit: efi_install_multiple_protocol_interfaces: 2
EFI: 2 returned by efi_install_multiple_protocol_interfaces( &efi_root, &efi_guid_firmware_management_protocol, &efi_fmp_raw, NULL) Command failed, result=1
To fix this issue, pass the handle variable as same as the efi_fmp_fit installation.
--- lib/efi_loader/efi_capsule.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
lib/efi_loader/efi_capsule.c +1 -1
@@ -949,7 +949,7 @@ efi_status_t __weak arch_efi_load_capsule_drivers(void)if (IS_ENABLED (CONFIG_EFI_CAPSULE_FIRMWARE_RAW )) { handle =NULL ; ret =EFI_CALL (efi_install_multiple_protocol_interfaces ( - &efi_root, + &handle, &efi_guid_firmware_management_protocol, &efi_fmp_raw,NULL )); }
PATCH v4 4/14 gpio: Introduce CONFIG_GPIO_EXTRA_HEADER to cleanup #ifdefs
In reply to Masami HiramatsuSince some SoCs and boards do not hae extra asm/arch/gpio.h, introduce CONFIG_GPIO_EXTRA_HEADER instead of adding !define(CONFIG_ARCH_XXXX) in asm/gpio.h.
---
Changes in v3:
- Change the config name to positive and selected by the opposite CONFIG_ARCH_*. (Build checked by Github CI)
--- arch/arm/Kconfig | 94 +++++++++++++++++++++++++++++++++++++++++++ arch/arm/include/asm/gpio.h | 8 ---- 2 files changed, 95 insertions(+), 7 deletions(-)
arch/arm/Kconfig +94 -0
@@ -90,6 +90,9 @@ config HAS_VBAR config HAS_THUMB2 bool +config GPIO_EXTRA_HEADER + bool + # Used for compatibility with asm files copied from the kernel config ARM_ASM_UNIFIED bool
@@ -518,25 +521,30 @@ choice config ARCH_AT91 bool "Atmel AT91" + select GPIO_EXTRA_HEADER select SPL_BOARD_INIT if SPL && !TARGET_SMARTWEB select SPL_SEPARATE_BSS if SPL config TARGET_EDB93XX bool "Support edb93xx" select CPU_ARM920T + select GPIO_EXTRA_HEADER select PL010_SERIAL config TARGET_ASPENITE bool "Support aspenite" select CPU_ARM926EJS + select GPIO_EXTRA_HEADER config TARGET_GPLUGD bool "Support gplugd" select CPU_ARM926EJS + select GPIO_EXTRA_HEADER config ARCH_DAVINCI bool "TI DaVinci" select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select SPL_DM_SPI if SPL imply CMD_SAVES help
@@ -547,6 +555,7 @@ config ARCH_KIRKWOOD select ARCH_MISC_INIT select BOARD_EARLY_INIT_F select CPU_ARM926EJS + select GPIO_EXTRA_HEADER config ARCH_MVEBU bool "Marvell MVEBU family (Armada XP/375/38x/3700/7K/8K)"
@@ -555,6 +564,7 @@ config ARCH_MVEBU select DM_SERIAL select DM_SPI select DM_SPI_FLASH + select GPIO_EXTRA_HEADER select SPL_DM_SPI if SPL select SPL_DM_SPI_FLASH if SPL select OF_CONTROL
@@ -565,11 +575,13 @@ config ARCH_MVEBU config ARCH_ORION5X bool "Marvell Orion" select CPU_ARM926EJS + select GPIO_EXTRA_HEADER config TARGET_SPEAR300 bool "Support spear300" select BOARD_EARLY_INIT_F select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select PL011_SERIAL imply CMD_SAVES
@@ -577,6 +589,7 @@ config TARGET_SPEAR310 bool "Support spear310" select BOARD_EARLY_INIT_F select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select PL011_SERIAL imply CMD_SAVES
@@ -584,6 +597,7 @@ config TARGET_SPEAR320 bool "Support spear320" select BOARD_EARLY_INIT_F select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select PL011_SERIAL imply CMD_SAVES
@@ -591,6 +605,7 @@ config TARGET_SPEAR600 bool "Support spear600" select BOARD_EARLY_INIT_F select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select PL011_SERIAL imply CMD_SAVES
@@ -601,6 +616,7 @@ config TARGET_STV0991 select DM_SERIAL select DM_SPI select DM_SPI_FLASH + select GPIO_EXTRA_HEADER select PL01X_SERIAL select SPI select SPI_FLASH
@@ -610,18 +626,21 @@ config TARGET_X600 bool "Support x600" select BOARD_LATE_INIT select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select PL011_SERIAL select SUPPORT_SPL config TARGET_FLEA3 bool "Support flea3" select CPU_ARM1136 + select GPIO_EXTRA_HEADER config ARCH_BCM283X bool "Broadcom BCM283X family" select DM select DM_GPIO select DM_SERIAL + select GPIO_EXTRA_HEADER select OF_CONTROL select PL01X_SERIAL select SERIAL_SEARCH_ALL
@@ -650,6 +669,7 @@ config ARCH_BCMSTB bool "Broadcom BCM7XXX family" select CPU_V7A select DM + select GPIO_EXTRA_HEADER select OF_CONTROL select OF_PRIOR_STAGE imply CMD_DM
@@ -660,6 +680,7 @@ config ARCH_BCMSTB config TARGET_BCMCYGNUS bool "Support bcmcygnus" select CPU_V7A + select GPIO_EXTRA_HEADER imply BCM_SF2_ETH imply BCM_SF2_ETH_GMAC imply CMD_HASH
@@ -671,6 +692,7 @@ config TARGET_BCMCYGNUS config TARGET_BCMNS2 bool "Support Broadcom Northstar2" select ARM64 + select GPIO_EXTRA_HEADER help Support for Broadcom Northstar 2 SoCs. NS2 is a quad-core 64-bit ARMv8 Cortex-A57 processors targeting a broad range of networking
@@ -695,6 +717,7 @@ config ARCH_EXYNOS select DM_SPI select DM_SPI_FLASH select SPI + select GPIO_EXTRA_HEADER imply SYS_THUMB_BUILD imply CMD_DM imply FAT_WRITE
@@ -706,6 +729,7 @@ config ARCH_S5PC1XX select DM_GPIO select DM_I2C select DM_SERIAL + select GPIO_EXTRA_HEADER imply CMD_DM config ARCH_HIGHBANK
@@ -726,6 +750,7 @@ config ARCH_INTEGRATOR bool "ARM Ltd. Integrator family" select DM select DM_SERIAL + select GPIO_EXTRA_HEADER select PL01X_SERIAL imply CMD_DM
@@ -736,6 +761,7 @@ config ARCH_IPQ40XX select DM_GPIO select DM_SERIAL select DM_RESET + select GPIO_EXTRA_HEADER select MSM_SMEM select PINCTRL select CLK
@@ -747,6 +773,7 @@ config ARCH_KEYSTONE bool "TI Keystone" select CMD_POWEROFF select CPU_V7A + select GPIO_EXTRA_HEADER select SUPPORT_SPL select SYS_ARCH_TIMER select SYS_THUMB_BUILD
@@ -763,6 +790,7 @@ config ARCH_K3 config ARCH_OMAP2PLUS bool "TI OMAP2+" select CPU_V7A + select GPIO_EXTRA_HEADER select SPL_BOARD_INIT if SPL select SPL_STACK_R if SPL select SUPPORT_SPL
@@ -771,6 +799,7 @@ config ARCH_OMAP2PLUS config ARCH_MESON bool "Amlogic Meson" + select GPIO_EXTRA_HEADER imply DISTRO_DEFAULTS imply DM_RNG help
@@ -781,6 +810,7 @@ config ARCH_MESON config ARCH_MEDIATEK bool "MediaTek SoCs" select DM + select GPIO_EXTRA_HEADER select OF_CONTROL select SPL_DM if SPL select SPL_LIBCOMMON_SUPPORT if SPL
@@ -797,6 +827,7 @@ config ARCH_LPC32XX select DM select DM_GPIO select DM_SERIAL + select GPIO_EXTRA_HEADER select SPL_DM if SPL select SUPPORT_SPL imply CMD_DM
@@ -805,12 +836,14 @@ config ARCH_IMX8 bool "NXP i.MX8 platform" select ARM64 select DM + select GPIO_EXTRA_HEADER select OF_CONTROL select ENABLE_ARM_SOC_BOOT0_HOOK config ARCH_IMX8M bool "NXP i.MX8M platform" select ARM64 + select GPIO_EXTRA_HEADER select SYS_FSL_HAS_SEC if IMX_HAB select SYS_FSL_SEC_COMPAT_4 select SYS_FSL_SEC_LE
@@ -823,33 +856,39 @@ config ARCH_IMXRT select CPU_V7M select DM select DM_SERIAL + select GPIO_EXTRA_HEADER select SUPPORT_SPL imply CMD_DM config ARCH_MX23 bool "NXP i.MX23 family" select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select PL011_SERIAL select SUPPORT_SPL config ARCH_MX25 bool "NXP MX25" select CPU_ARM926EJS + select GPIO_EXTRA_HEADER imply MXC_GPIO config ARCH_MX28 bool "NXP i.MX28 family" select CPU_ARM926EJS + select GPIO_EXTRA_HEADER select PL011_SERIAL select SUPPORT_SPL config ARCH_MX31 bool "NXP i.MX31 family" select CPU_ARM1136 + select GPIO_EXTRA_HEADER config ARCH_MX7ULP bool "NXP MX7ULP" select CPU_V7A + select GPIO_EXTRA_HEADER select SYS_FSL_HAS_SEC if IMX_HAB select SYS_FSL_SEC_COMPAT_4 select SYS_FSL_SEC_LE
@@ -861,6 +900,7 @@ config ARCH_MX7 bool "Freescale MX7" select ARCH_MISC_INIT select CPU_V7A + select GPIO_EXTRA_HEADER select SYS_FSL_HAS_SEC if IMX_HAB select SYS_FSL_SEC_COMPAT_4 select SYS_FSL_SEC_LE
@@ -871,6 +911,7 @@ config ARCH_MX7 config ARCH_MX6 bool "Freescale MX6" select CPU_V7A + select GPIO_EXTRA_HEADER select SYS_FSL_HAS_SEC select SYS_FSL_SEC_COMPAT_4 select SYS_FSL_SEC_LE
@@ -886,18 +927,21 @@ config ARCH_MX5 bool "Freescale MX5" select BOARD_EARLY_INIT_F select CPU_V7A + select GPIO_EXTRA_HEADER imply MXC_GPIO config ARCH_NEXELL bool "Nexell S5P4418/S5P6818 SoC" select ENABLE_ARM_SOC_BOOT0_HOOK select DM + select GPIO_EXTRA_HEADER config ARCH_OWL bool "Actions Semi OWL SoCs" select DM select DM_ETH select DM_SERIAL + select GPIO_EXTRA_HEADER select OWL_SERIAL select CLK select CLK_OWL
@@ -920,6 +964,7 @@ config ARCH_RMOBILE bool "Renesas ARM SoCs" select DM select DM_SERIAL + select GPIO_EXTRA_HEADER imply BOARD_EARLY_INIT_F imply CMD_DM imply FAT_WRITE
@@ -932,6 +977,7 @@ config ARCH_SNAPDRAGON select DM select DM_GPIO select DM_SERIAL + select GPIO_EXTRA_HEADER select MSM_SMEM select OF_CONTROL select OF_SEPARATE
@@ -947,6 +993,7 @@ config ARCH_SOCFPGA select CPU_V7A if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10 select DM select DM_SERIAL + select GPIO_EXTRA_HEADER select ENABLE_ARM_SOC_BOOT0_HOOK if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10 select OF_CONTROL select SPL_DM_RESET if DM_RESET
@@ -998,6 +1045,7 @@ config ARCH_SUNXI select DM_SCSI if SCSI select DM_SERIAL select DM_USB if DISTRO_DEFAULTS + select GPIO_EXTRA_HEADER select OF_BOARD_SETUP select OF_CONTROL select OF_SEPARATE
@@ -1057,6 +1105,7 @@ config ARCH_VERSAL select DM_ETH if NET select DM_MMC if MMC select DM_SERIAL + select GPIO_EXTRA_HEADER select OF_CONTROL imply BOARD_LATE_INIT imply ENV_VARS_UBOOT_RUNTIME_CONFIG
@@ -1064,6 +1113,7 @@ config ARCH_VERSAL config ARCH_VF610 bool "Freescale Vybrid" select CPU_V7A + select GPIO_EXTRA_HEADER select SYS_FSL_ERRATUM_ESDHC111 imply CMD_MTDPARTS imply MTD_RAW_NAND
@@ -1080,6 +1130,7 @@ config ARCH_ZYNQ select DM_SPI select DM_SPI_FLASH select DM_USB if USB + select GPIO_EXTRA_HEADER select OF_CONTROL select SPI select SPL_BOARD_INIT if SPL
@@ -1106,6 +1157,7 @@ config ARCH_ZYNQMP_R5 select DM_ETH if NET select DM_MMC if MMC select DM_SERIAL + select GPIO_EXTRA_HEADER select OF_CONTROL imply CMD_DM imply DM_USB_GADGET
@@ -1123,6 +1175,7 @@ config ARCH_ZYNQMP select DM_SPI_FLASH if DM_SPI select DM_USB if USB select FIRMWARE + select GPIO_EXTRA_HEADER select OF_CONTROL select SPL_BOARD_INIT if SPL select SPL_CLK if SPL
@@ -1143,23 +1196,27 @@ config ARCH_ZYNQMP config ARCH_TEGRA bool "NVIDIA Tegra" + select GPIO_EXTRA_HEADER imply DISTRO_DEFAULTS imply FAT_WRITE config TARGET_VEXPRESS64_AEMV8A bool "Support vexpress_aemv8a" select ARM64 + select GPIO_EXTRA_HEADER select PL01X_SERIAL config TARGET_VEXPRESS64_BASE_FVP bool "Support Versatile Express ARMv8a FVP BASE model" select ARM64 + select GPIO_EXTRA_HEADER select PL01X_SERIAL select SEMIHOSTING config TARGET_VEXPRESS64_JUNO bool "Support Versatile Express Juno Development Platform" select ARM64 + select GPIO_EXTRA_HEADER select PL01X_SERIAL select DM select OF_CONTROL
@@ -1188,6 +1245,7 @@ config TARGET_LS2080A_EMU select ARM64 select ARMV8_MULTIENTRY select FSL_DDR_SYNC_REFRESH + select GPIO_EXTRA_HEADER help Support for Freescale LS2080A_EMU platform. The LS2080A Development System (EMULATOR) is a pre-silicon
@@ -1201,6 +1259,7 @@ config TARGET_LS1088AQDS select ARMV8_MULTIENTRY select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER select SUPPORT_SPL select FSL_DDR_INTERACTIVE if !SD_BOOT help
@@ -1216,6 +1275,7 @@ config TARGET_LS2080AQDS select ARMV8_MULTIENTRY select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER select SUPPORT_SPL imply SCSI imply SCSI_AHCI
@@ -1237,6 +1297,7 @@ config TARGET_LS2080ARDB select SUPPORT_SPL select FSL_DDR_BIST select FSL_DDR_INTERACTIVE if !SPL + select GPIO_EXTRA_HEADER imply SCSI imply SCSI_AHCI help
@@ -1251,6 +1312,7 @@ config TARGET_LS2081ARDB select ARM64 select ARMV8_MULTIENTRY select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER select SUPPORT_SPL help Support for Freescale LS2081ARDB platform.
@@ -1265,6 +1327,7 @@ config TARGET_LX2160ARDB select ARMV8_MULTIENTRY select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER help Support for NXP LX2160ARDB platform. The lx2160ardb (LX2160A Reference design board (RDB)
@@ -1278,6 +1341,7 @@ config TARGET_LX2160AQDS select ARMV8_MULTIENTRY select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER help Support for NXP LX2160AQDS platform. The lx2160aqds (LX2160A QorIQ Development System (QDS)
@@ -1292,6 +1356,7 @@ config TARGET_LX2162AQDS select ARMV8_MULTIENTRY select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER help Support for NXP LX2162AQDS platform. The lx2162aqds support is based on LX2160A Layerscape Architecture processor.
@@ -1302,6 +1367,7 @@ config TARGET_HIKEY select DM select DM_GPIO select DM_SERIAL + select GPIO_EXTRA_HEADER select OF_CONTROL select PL01X_SERIAL select SPECIFY_CONSOLE_INDEX
@@ -1315,6 +1381,7 @@ config TARGET_HIKEY960 select ARM64 select DM select DM_SERIAL + select GPIO_EXTRA_HEADER select OF_CONTROL select PL01X_SERIAL imply CMD_DM
@@ -1328,6 +1395,7 @@ config TARGET_POPLAR select DM select DM_SERIAL select DM_USB + select GPIO_EXTRA_HEADER select OF_CONTROL select PL01X_SERIAL imply CMD_DM
@@ -1343,6 +1411,7 @@ config TARGET_LS1012AQDS select ARM64 select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER help Support for Freescale LS1012AQDS platform. The LS1012A Development System (QDS) is a high-performance
@@ -1355,6 +1424,7 @@ config TARGET_LS1012ARDB select ARM64 select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER imply SCSI imply SCSI_AHCI help
@@ -1369,6 +1439,7 @@ config TARGET_LS1012A2G5RDB select ARM64 select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER imply SCSI help Support for Freescale LS1012A2G5RDB platform.
@@ -1382,6 +1453,7 @@ config TARGET_LS1012AFRWY select ARM64 select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER imply SCSI imply SCSI_AHCI help
@@ -1395,6 +1467,7 @@ config TARGET_LS1012AFRDM select ARCH_LS1012A select ARM64 select ARCH_SUPPORT_TFABOOT + select GPIO_EXTRA_HEADER help Support for Freescale LS1012AFRDM platform. The LS1012A Freedom board (FRDM) is a high-performance
@@ -1408,6 +1481,7 @@ config TARGET_LS1028AQDS select ARMV8_MULTIENTRY select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER help Support for Freescale LS1028AQDS platform The LS1028A Development System (QDS) is a high-performance
@@ -1421,6 +1495,7 @@ config TARGET_LS1028ARDB select ARMV8_MULTIENTRY select ARCH_SUPPORT_TFABOOT select BOARD_LATE_INIT + select GPIO_EXTRA_HEADER help Support for Freescale LS1028ARDB platform The LS1028A Development System (RDB) is a high-performance
@@ -1436,6 +1511,7 @@ config TARGET_LS1088ARDB select BOARD_LATE_INIT select SUPPORT_SPL select FSL_DDR_INTERACTIVE if !SD_BOOT + select GPIO_EXTRA_HEADER help Support for NXP LS1088ARDB platform. The LS1088A Reference design board (RDB) is a high-performance
@@ -1456,6 +1532,7 @@ config TARGET_LS1021AQDS select SYS_FSL_DDR select FSL_DDR_INTERACTIVE select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI + select GPIO_EXTRA_HEADER select SPI_FLASH_DATAFLASH if FSL_DSPI || FSL_QSPI imply SCSI
@@ -1471,6 +1548,7 @@ config TARGET_LS1021ATWR select LS1_DEEP_SLEEP select SUPPORT_SPL select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI + select GPIO_EXTRA_HEADER imply SCSI config TARGET_PG_WCOM_SELI8
@@ -1484,6 +1562,7 @@ config TARGET_PG_WCOM_SELI8 select CPU_V7_HAS_VIRT select SYS_FSL_DDR select FSL_DDR_INTERACTIVE + select GPIO_EXTRA_HEADER select VENDOR_KM imply SCSI help
@@ -1502,6 +1581,7 @@ config TARGET_LS1021ATSN select CPU_V7_HAS_VIRT select LS1_DEEP_SLEEP select SUPPORT_SPL + select GPIO_EXTRA_HEADER imply SCSI config TARGET_LS1021AIOT
@@ -1514,6 +1594,7 @@ config TARGET_LS1021AIOT select CPU_V7_HAS_VIRT select SUPPORT_SPL select DM_SPI_FLASH if FSL_DSPI || FSL_QSPI + select GPIO_EXTRA_HEADER imply SCSI help Support for Freescale LS1021AIOT platform.
@@ -1533,6 +1614,7 @@ config TARGET_LS1043AQDS select FSL_DDR_INTERACTIVE if !SPL select FSL_DSPI if !SPL_NO_DSPI select DM_SPI_FLASH if FSL_DSPI + select GPIO_EXTRA_HEADER imply SCSI imply SCSI_AHCI help
@@ -1549,6 +1631,7 @@ config TARGET_LS1043ARDB select SUPPORT_SPL select FSL_DSPI if !SPL_NO_DSPI select DM_SPI_FLASH if FSL_DSPI + select GPIO_EXTRA_HEADER help Support for Freescale LS1043ARDB platform.
@@ -1565,6 +1648,7 @@ config TARGET_LS1046AQDS select FSL_DDR_BIST if !SPL select FSL_DDR_INTERACTIVE if !SPL select FSL_DDR_INTERACTIVE if !SPL + select GPIO_EXTRA_HEADER imply SCSI help Support for Freescale LS1046AQDS platform.
@@ -1585,6 +1669,7 @@ config TARGET_LS1046ARDB select SUPPORT_SPL select FSL_DDR_BIST select FSL_DDR_INTERACTIVE if !SPL + select GPIO_EXTRA_HEADER imply SCSI help Support for Freescale LS1046ARDB platform.
@@ -1601,6 +1686,7 @@ config TARGET_LS1046AFRWY select BOARD_EARLY_INIT_F select BOARD_LATE_INIT select DM_SPI_FLASH if DM_SPI + select GPIO_EXTRA_HEADER imply SCSI help Support for Freescale LS1046AFRWY platform.
@@ -1629,6 +1715,7 @@ config TARGET_SL28 select DM_SERIAL select DM_SPI select DM_USB + select GPIO_EXTRA_HEADER select SPL_DM if SPL select SPL_DM_SPI if SPL select SPL_DM_SPI_FLASH if SPL
@@ -1641,6 +1728,7 @@ config TARGET_SL28 config TARGET_COLIBRI_PXA270 bool "Support colibri_pxa270" select CPU_PXA + select GPIO_EXTRA_HEADER config ARCH_UNIPHIER bool "Socionext UniPhier SoCs"
@@ -1677,6 +1765,7 @@ config ARCH_STM32 select CPU_V7M select DM select DM_SERIAL + select GPIO_EXTRA_HEADER imply CMD_DM config ARCH_STI
@@ -1702,6 +1791,7 @@ config ARCH_STM32MP select DM_GPIO select DM_RESET select DM_SERIAL + select GPIO_EXTRA_HEADER select MISC select OF_CONTROL select OF_LIBFDT
@@ -1764,6 +1854,7 @@ config ARCH_OCTEONTX bool "Support OcteonTX SoCs" select CLK select DM + select GPIO_EXTRA_HEADER select ARM64 select OF_CONTROL select OF_LIVE
@@ -1774,6 +1865,7 @@ config ARCH_OCTEONTX2 bool "Support OcteonTX2 SoCs" select CLK select DM + select GPIO_EXTRA_HEADER select ARM64 select OF_CONTROL select OF_LIVE
@@ -1783,6 +1875,7 @@ config ARCH_OCTEONTX2 config TARGET_THUNDERX_88XX bool "Support ThunderX 88xx" select ARM64 + select GPIO_EXTRA_HEADER select OF_CONTROL select PL01X_SERIAL select SYS_CACHE_SHIFT_7
@@ -1796,6 +1889,7 @@ config ARCH_ASPEED config TARGET_DURIAN bool "Support Phytium Durian Platform" select ARM64 + select GPIO_EXTRA_HEADER help Support for durian platform. It has 2GB Sdram, uart and pcie.
arch/arm/include/asm/gpio.h +1 -7
@@ -1,10 +1,4 @@ -#if !defined(CONFIG_ARCH_UNIPHIER ) && !defined(CONFIG_ARCH_STI ) && \ - !defined(CONFIG_ARCH_K3 ) && !defined(CONFIG_ARCH_BCM68360 ) && \ - !defined(CONFIG_ARCH_BCM6858 ) && !defined(CONFIG_ARCH_BCM63158 ) && \ - !defined(CONFIG_ARCH_ROCKCHIP ) && !defined(CONFIG_ARCH_ASPEED ) && \ - !defined(CONFIG_ARCH_U8500 ) && !defined(CONFIG_CORTINA_PLATFORM ) && \ - !defined(CONFIG_TARGET_BCMNS3 ) && !defined(CONFIG_TARGET_TOTAL_COMPUTE ) && \ - !defined(CONFIG_ARCH_QEMU ) +#ifdef CONFIG_GPIO_EXTRA_HEADER #include <asm/arch/gpio.h> #endif #include <asm-generic/gpio.h>
PATCH v4 5/14 pci: synquacer: Add SynQuacer ECAM based PCIe driver
In reply to Masami HiramatsuAdd ECAM based SynQuacer PCIe RC driver. This driver configures the PCIe RC and filter out a ghost pcie config.
Since the Linux kernel expects "socionext,synquacer-pcie-ecam" device is configured by firmware (EDK2), it doesn't re-configure in the kernel. So as same as EDK2, U-Boot needs to configure it before boot the kernel.
--- drivers/pci/Kconfig | 12 + drivers/pci/Makefile | 1 drivers/pci/pcie_ecam_synquacer.c | 600 +++++++++++++++++++++++++++++++++++++ 3 files changed, 613 insertions(+) create mode 100644 drivers/pci/pcie_ecam_synquacer.c
drivers/pci/Kconfig +12 -0
@@ -81,6 +81,18 @@ config PCIE_ECAM_GENERIC Say Y here if you want to enable support for generic ECAM-based PCIe host controllers, such as the one emulated by QEMU. +config PCIE_ECAM_SYNQUACER + bool "SynQuacer ECAM-based PCI host controller support" + default n + depends on DM_PCI + select PCI_INIT_R + select PCI_REGION_MULTI_ENTRY + help + Say Y here if you want to enable support for Socionext + SynQuacer SoC's ECAM-based PCIe host controllers. + Note that this must be configured when boot because Linux driver + expects the PCIe RC has been configured in the bootloader. + config PCI_PHYTIUM bool "Phytium PCIe support" depends on DM_PCI
drivers/pci/Makefile +1 -0
@@ -16,6 +16,7 @@ endif obj-$(CONFIG_PCI) += pci_auto_common.o pci_common.o obj-$(CONFIG_PCIE_ECAM_GENERIC) += pcie_ecam_generic.o +obj-$(CONFIG_PCIE_ECAM_SYNQUACER) += pcie_ecam_synquacer.o obj-$(CONFIG_FSL_PCI_INIT) += fsl_pci_init.o obj-$(CONFIG_PCI_INDIRECT_BRIDGE) += pci_indirect.o obj-$(CONFIG_PCI_GT64120) += pci_gt64120.o
drivers/pci/pcie_ecam_synquacer.c new file +600 -0
600 lines not on this page · raw message
PATCH v4 6/14 mmc: synquacer: Add SynQuacer F_SDH30 SDHCI driver
In reply to Masami HiramatsuFrom: Jassi Brar <[email protected]>
---
Changes in v4:
- Add Jaehoon's reviewed-by.
Changes in v3:
- Rename config name to MMC_SDHCI_F_SDH30.
- Remove unneeded wait in drivers/mmc/sdhci.c.
- Rename probe function to f_sdh30_sdhci_probe.
--- drivers/mmc/Kconfig | 10 ++++++ drivers/mmc/Makefile | 1 + drivers/mmc/f_sdh30.c | 81 +++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 92 insertions(+) create mode 100644 drivers/mmc/f_sdh30.c
drivers/mmc/Kconfig +10 -0
@@ -561,6 +561,16 @@ config MMC_SDHCI_IPROC If unsure, say N. +config MMC_SDHCI_F_SDH30 + bool "SDHCI support for Fujitsu Semiconductor F_SDH30" + depends on BLK && DM_MMC + depends on MMC_SDHCI + help + This selects the Secure Digital Host Controller Interface (SDHCI) + Needed by some Fujitsu SoC for MMC / SD / SDIO support. + If you have a controller with this interface, say Y or M here. + If unsure, say N. + config MMC_SDHCI_KONA bool "SDHCI support on Broadcom KONA platform" depends on MMC_SDHCI
drivers/mmc/Makefile +1 -0
@@ -76,3 +76,4 @@ obj-$(CONFIG_MMC_UNIPHIER) += tmio-common.o uniphier-sd.o obj-$(CONFIG_RENESAS_SDHI) += tmio-common.o renesas-sdhi.o obj-$(CONFIG_MMC_BCM2835) += bcm2835_sdhost.o obj-$(CONFIG_MMC_MTK) += mtk-sd.o +obj-$(CONFIG_MMC_SDHCI_F_SDH30) += f_sdh30.o
drivers/mmc/f_sdh30.c new file +81 -0
81 lines not on this page · raw message
PATCH v4 7/14 spi: synquacer: Add HSSPI SPI controller driver for SynQuacer
In reply to Masami HiramatsuFrom: Jassi Brar <[email protected]>
This is a driver for the HSSPI SPI controller on SynQuacer SoC. The HSSPI has command sequence mode (memory mapped) and direct mode (FIFO access). The driver will operate it under the direct mode. And before booting OS, it switch back to the command sequence mode since that is compatible with default EDK2 behavior.
--- drivers/spi/Kconfig | 8 + drivers/spi/Makefile | 1 drivers/spi/spi-synquacer.c | 491 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 500 insertions(+) create mode 100644 drivers/spi/spi-synquacer.c
drivers/spi/Kconfig +8 -0
@@ -481,4 +481,12 @@ config MXC_SPI Enable the MXC SPI controller driver. This driver can be used on various i.MX SoCs such as i.MX31/35/51/6/7. +config SYNQUACER_SPI + bool "Socionext SynQuacer HS-SPI driver" + depends on ARCH_SYNQUACER + help + Enable the Socionext HS-SPI driver for SynQuacer. This driver can + be used to access the SPI interface and SPI NOR flash on platforms + embedding this HS-SPI IP core. + endif # menu "SPI Support"
drivers/spi/Makefile +1 -0
@@ -31,6 +31,7 @@ obj-$(CONFIG_EXYNOS_SPI) += exynos_spi.o obj-$(CONFIG_FSL_DSPI) += fsl_dspi.o obj-$(CONFIG_FSL_ESPI) += fsl_espi.o obj-$(CONFIG_FSL_QSPI) += fsl_qspi.o +obj-$(CONFIG_SYNQUACER_SPI) += spi-synquacer.o obj-$(CONFIG_ICH_SPI) += ich.o obj-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o obj-$(CONFIG_MESON_SPIFC) += meson_spifc.o
drivers/spi/spi-synquacer.c new file +491 -0
491 lines not on this page · raw message
PATCH v4 8/14 net: synquacer: Add netsec driver
In reply to Masami HiramatsuFrom: Jassi Brar <[email protected]>
Add SynQuacer's NETSEC GbE controller driver. Since this driver will load the firmware from SPI NOR flash, this depends on CONFIG_SYNQUACER_SPI=y.
--- drivers/net/Kconfig | 8 drivers/net/Makefile | 1 drivers/net/sni_netsec.c | 1134 ++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 1143 insertions(+) create mode 100644 drivers/net/sni_netsec.c
drivers/net/Kconfig +8 -0
@@ -673,6 +673,14 @@ config SNI_AVE This driver implements support for the Socionext AVE Ethernet controller, as found on the Socionext UniPhier family. +config SNI_NETSEC + bool "Socionext NETSEC Ethernet support" + depends on DM_ETH && SYNQUACER_SPI + select PHYLIB + help + This driver implements support for the Socionext SynQuacer NETSEC + ethernet controller, as found on the Socionext SynQuacer family. + source "drivers/net/mscc_eswitch/Kconfig" config ETHER_ON_FEC1
drivers/net/Makefile +1 -0
@@ -90,6 +90,7 @@ obj-$(CONFIG_DWC_ETH_QOS) += dwc_eth_qos.o obj-$(CONFIG_FSL_PFE) += pfe_eth/ obj-y += qe/ obj-$(CONFIG_SNI_AVE) += sni_ave.o +obj-$(CONFIG_SNI_NETSEC) += sni_netsec.o obj-y += ti/ obj-$(CONFIG_MEDIATEK_ETH) += mtk_eth.o obj-y += mscc_eswitch/
drivers/net/sni_netsec.c new file +1134 -0
1,134 lines not on this page · raw message
PATCH v4 9/14 i2c: synquacer: SNI Synquacer I2C controller
In reply to Masami HiramatsuFrom: Jassi Brar <[email protected]>
Add driver for class of I2C controllers found on
Socionext Synquacer platform.
--- drivers/i2c/Kconfig | 7 + drivers/i2c/Makefile | 1 drivers/i2c/synquacer_i2c.c | 338 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 346 insertions(+) create mode 100644 drivers/i2c/synquacer_i2c.c
drivers/i2c/Kconfig +7 -0
@@ -455,6 +455,13 @@ config SYS_I2C_STM32F7 _ Optional clock stretching _ Software reset +config SYS_I2C_SYNQUACER + bool "Socionext SynQuacer I2C controller" + depends on ARCH_SYNQUACER && DM_I2C + help + Support for Socionext Synquacer I2C controller. This I2C controller + will be used for RTC and LS-connector on DeveloperBox. + config SYS_I2C_TEGRA bool "NVIDIA Tegra internal I2C controller" depends on ARCH_TEGRA
drivers/i2c/Makefile +1 -0
@@ -43,6 +43,7 @@ obj-$(CONFIG_SYS_I2C_SANDBOX) += sandbox_i2c.o i2c-emul-uclass.o obj-$(CONFIG_SYS_I2C_SH) += sh_i2c.o obj-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o obj-$(CONFIG_SYS_I2C_STM32F7) += stm32f7_i2c.o +obj-$(CONFIG_SYS_I2C_SYNQUACER) += synquacer_i2c.o obj-$(CONFIG_SYS_I2C_TEGRA) += tegra_i2c.o obj-$(CONFIG_SYS_I2C_UNIPHIER) += i2c-uniphier.o obj-$(CONFIG_SYS_I2C_UNIPHIER_F) += i2c-uniphier-f.o
drivers/i2c/synquacer_i2c.c new file +338 -0
338 lines not on this page · raw message
PATCH v4 10/14 ARM: dts: synquacer: Add device trees for DeveloperBox
In reply to Masami HiramatsuAdd device trees for 96boards EE DeveloperBox and basement SynQuacer SoC dtsi. These files are imported from EDK2
commit 83d38b0b4c0f240d4488c600bbe87cea391f3922
as-is (except for the changes #include path and some macros).
And add U-Boot specific changes in synquacer-sc2a11-developerbox-u-boot.dtsi
---
Changes in v4:
- Add i2c0 and RTC node.
Changes in v3:
- Use generic nor flash instead of specific mx25u51245g. (chip parameters will be searched by the register value)
Changes in v2:
- Add reference commit id of original EDK2 to the comment
- Just copy the EDK2 dts files as-is (change #include path)
- Split out the u-boot specific changes in -u-boot.dtsi.
- Removed unneeded spi-nor flash partition information.
--- arch/arm/dts/Makefile | 2 arch/arm/dts/synquacer-sc2a11-caches.dtsi | 73 ++ .../dts/synquacer-sc2a11-developerbox-u-boot.dtsi | 75 +++ arch/arm/dts/synquacer-sc2a11-developerbox.dts | 56 ++ arch/arm/dts/synquacer-sc2a11.dtsi | 595 ++++++++++++++++++++ 5 files changed, 801 insertions(+) create mode 100644 arch/arm/dts/synquacer-sc2a11-caches.dtsi create mode 100644 arch/arm/dts/synquacer-sc2a11-developerbox-u-boot.dtsi create mode 100644 arch/arm/dts/synquacer-sc2a11-developerbox.dts create mode 100644 arch/arm/dts/synquacer-sc2a11.dtsi
arch/arm/dts/Makefile +2 -0
@@ -1099,6 +1099,8 @@ dtb-$(CONFIG_TARGET_PRESIDIO_ASIC) += ca-presidio-engboard.dtb dtb-$(CONFIG_TARGET_IMX8MM_CL_IOT_GATE) += imx8mm-cl-iot-gate.dtb +dtb-$(CONFIG_ARCH_SYNQUACER) += synquacer-sc2a11-developerbox.dtb + targets += $(dtb-y) # Add any required device tree compiler flags here
arch/arm/dts/synquacer-sc2a11-caches.dtsi new file +73 -0
73 lines not on this page · raw message
arch/arm/dts/synquacer-sc2a11-developerbox-u-boot.dtsi new file +75 -0
75 lines not on this page · raw message
arch/arm/dts/synquacer-sc2a11-developerbox.dts new file +56 -0
56 lines not on this page · raw message
arch/arm/dts/synquacer-sc2a11.dtsi new file +595 -0
595 lines not on this page · raw message
PATCH v4 11/14 board: synquacer: Add DeveloperBox 96boards EE support
In reply to Masami HiramatsuAdd the DeveloperBox 96boards EE support. This board is also known as Socionext SynQuacer E-Series. It contians one "SC2A11" SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots, 3 PCIe slots (1 4x port and 2 1x ports which are expanded via PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard MicroATX Form Factor.
For more information, see this page;
https://www.96boards.org/product/developerbox/
---
Changes in v4:
- Add I2C and RTC configuration.
- Enable RTC and Date command.
- Remove I2C0 node before booting linux to hide it same as EDK2 does.
- Add some configurations to make it EBBR compliant.
Changes in v3:
- Enable CONFIG_MMC_SDHCI_F_SDH30.
- Enable CONFIG_CMD_GENERIC (fstype command) for distro boot.
- Remove unneeded CONFIG_ONLY_GENERIC_GPIO.
Changes in v2:
- Do not include arch/gpio.h and remove arch-sc2a11/gpio.h.
- Remove non-UEFI boot commands.
- Use Distro boot.
- Remove NOR-connected SPI node by path instead of alias.
- Rename configs/SynQuacer_defconfig to configs/synquacer_developerbox_defconfig.
- Rename include/configs/SynQuacer.h to include/configs/synquacer.h.
- Move README under doc/board/socionext/ and make it .rst text.
--- arch/arm/Kconfig | 14 +++ board/socionext/developerbox/Kconfig | 36 +++++++ board/socionext/developerbox/MAINTAINERS | 14 +++ board/socionext/developerbox/Makefile | 9 ++ board/socionext/developerbox/developerbox.c | 146 +++++++++++++++++++++++++++ configs/synquacer_developerbox_defconfig | 114 +++++++++++++++++++++ doc/board/index.rst | 1 doc/board/socionext/developerbox.rst | 87 ++++++++++++++++ doc/board/socionext/index.rst | 9 ++ include/configs/synquacer.h | 109 ++++++++++++++++++++ 10 files changed, 539 insertions(+) create mode 100644 board/socionext/developerbox/Kconfig create mode 100644 board/socionext/developerbox/MAINTAINERS create mode 100644 board/socionext/developerbox/Makefile create mode 100644 board/socionext/developerbox/developerbox.c create mode 100644 configs/synquacer_developerbox_defconfig create mode 100644 doc/board/socionext/developerbox.rst create mode 100644 doc/board/socionext/index.rst create mode 100644 include/configs/synquacer.h
arch/arm/Kconfig +14 -0
@@ -1760,6 +1760,19 @@ config ARCH_UNIPHIER Support for UniPhier SoC family developed by Socionext Inc. (formerly, System LSI Business Division of Panasonic Corporation) +config ARCH_SYNQUACER + bool "Socionext SynQuacer SoCs" + select ARM64 + select DM + select GIC_V3 + select PSCI_RESET + select SYSRESET + select SYSRESET_PSCI + select OF_CONTROL + help + Support for SynQuacer SoC family developed by Socionext Inc. + This SoC is used on 96boards EE DeveloperBox. + config ARCH_STM32 bool "Support STMicroelectronics STM32 MCU with cortex M" select CPU_V7M
@@ -2102,6 +2115,7 @@ source "board/hisilicon/poplar/Kconfig" source "board/isee/igep003x/Kconfig" source "board/kontron/sl28/Kconfig" source "board/myir/mys_6ulx/Kconfig" +source "board/socionext/developerbox/Kconfig" source "board/spear/spear300/Kconfig" source "board/spear/spear310/Kconfig" source "board/spear/spear320/Kconfig"
board/socionext/developerbox/Kconfig new file +36 -0
@@ -0,0 +1,36 @@ +if ARCH_SYNQUACER + +choice + prompt "SC2A11 Cortex-A53 MPCore 24cores" + optional + +config TARGET_DEVELOPERBOX + bool "Socionext DeveloperBox" + select PCI + select DM_PCI + select PCIE_ECAM_SYNQUACER + select SYS_DISABLE_DCACHE_OPS + select OF_BOARD_SETUP + help + Choose this option if you build the U-Boot for the DeveloperBox + 96boards Enterprise Edition. + This board will booted from SCP firmware and it enables SMMU, thus + the dcache is updated automatically when DMA operation is executed. +endchoice + +config SYS_SOC + default "sc2a11" + +if TARGET_DEVELOPERBOX + +config SYS_BOARD + default "developerbox" + +config SYS_VENDOR + default "socionext" + +config SYS_CONFIG_NAME + default "synquacer" + +endif +endif
board/socionext/developerbox/MAINTAINERS new file +14 -0
@@ -0,0 +1,14 @@ +DEVELOPER BOX +M: Masami Hiramatsu <[email protected]> +M: Jassi Brar <[email protected]> +S: Maintained +F: arch/arm/dts/synquacer-* +F: board/socionext/developerbox/* +F: configs/synquacer_developerbox_defconfig +F: drivers/i2c/synquacer_i2c.c +F: drivers/mmc/f_sdh30.c +F: drivers/net/sni_netsec.c +F: drivers/pci/pcie_ecam_synquacer.c +F: drivers/spi/spi-synquacer.c +F: include/configs/synquacer.h +F: doc/board/socionext/developerbox.rst
board/socionext/developerbox/Makefile new file +9 -0
@@ -0,0 +1,9 @@ +# +# Author: Masami Hiramatsu <[email protected]> +# +# Copyright (C) 2021 Linaro Ltd. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := developerbox.o
board/socionext/developerbox/developerbox.c new file +146 -0
146 lines not on this page · raw message
configs/synquacer_developerbox_defconfig new file +114 -0
114 lines not on this page · raw message
doc/board/index.rst +1 -0
@@ -21,6 +21,7 @@ Board-specific doc rockchip/index sifive/index sipeed/index + socionext/index st/index tbs/index toradex/index
doc/board/socionext/developerbox.rst new file +87 -0
87 lines not on this page · raw message
doc/board/socionext/index.rst new file +9 -0
@@ -0,0 +1,9 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Socionext +========= + +.. toctree:: + :maxdepth: 2 + + developerbox
include/configs/synquacer.h new file +109 -0
109 lines not on this page · raw message
PATCH v4 12/14 dfu_mtd: Ignore non-implemented lock device failure
In reply to Masami HiramatsuIgnore the non-implemented lock device failure on writing mtd via DFU. Without this fix, DFU write shows an error on such device even if it succeeded, because dfu->write_medium returns -EOPNOTSUPP.
--- drivers/dfu/dfu_mtd.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/dfu/dfu_mtd.c +2 -0
@@ -152,6 +152,8 @@ static int mtd_block_op(enum dfu_op op, struct dfu_entity *dfu, ret =mtd_lock (mtd, lock_ofs, lock_len);if (ret && ret != -EOPNOTSUPP )printf ("MTD device lock failed\n" ); +if (ret == -EOPNOTSUPP ) + ret =0 ; }return ret; }
PATCH v4 13/14 doc: qemu: arm64: Fix the documentation of capsule update
In reply to Masami HiramatsuSince the EDK2 GenerateCapsule script is out of date and it doesn't generate the supported version capsule file, the document should refer the mkeficapsule in tools.
--- doc/board/emulation/qemu_capsule_update.rst | 11 ++--------- 1 file changed, 2 insertions(+), 9 deletions(-)
doc/board/emulation/qemu_capsule_update.rst +2 -9
@@ -39,16 +39,9 @@ In addition, the following config needs to be disabled(QEMU ARM specific):: CONFIG_TFABOOT -The capsule file can be generated by using the GenerateCapsule.py -script in EDKII:: - - $ ./BaseTools/BinWrappers/PosixLike/GenerateCapsule -e -o \ - <capsule_file_name> --fw-version <val> --lsv <val> --guid \ - e2bb9c06-70e9-4b14-97a3-5a7913176e3f --verbose --update-image-index \ - <val> --verbose <u-boot.bin> +The capsule file can be generated by using the tools/mkeficapsule:: -The above is a wrapper script(GenerateCapsule) which eventually calls -the actual GenerateCapsule.py script. + $ mkeficapsule --raw <u-boot.bin> --index 1 <capsule_file_name> As per the UEFI specification, the capsule file needs to be placed on the EFI System Partition, under the \EFI\UpdateCapsule directory. The
PATCH v4 14/14 configs: synquacer: Enable EFI capsule update support
In reply to Masami HiramatsuEnable EFI capsule update support. With the EFI capsule update, you can update U-Boot, TF-A and OP-TEE. TF-A and OP-TEE are usually combined as a FIP binary, but if the binary is bigger than 480KB, you have to modify FIP header, split the OP-TEE and stores the OP-TEE binary in the different place. This configuration supports both cases.
---
Changes in v4:
- Add some config options for EBBR.
Changes in v3:
- Fix a typo in dfu_alt_info.
--- configs/synquacer_developerbox_defconfig | 17 +++++++++++++++++ include/configs/synquacer.h | 6 ++++++ 2 files changed, 23 insertions(+)
configs/synquacer_developerbox_defconfig +17 -0
@@ -112,3 +112,20 @@ CONFIG_DM_USB=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_PCI=y CONFIG_USB_STORAGE=y +CONFIG_EFI_RUNTIME_UPDATE_CAPSULE=y +CONFIG_EFI_CAPSULE_ON_DISK=y +CONFIG_EFI_CAPSULE_FIRMWARE_MANAGEMENT=y +CONFIG_EFI_CAPSULE_FIRMWARE=y +CONFIG_EFI_CAPSULE_FIRMWARE_RAW=y +CONFIG_EFI_CAPSULE_FIRMWARE_FIT=y +CONFIG_EFI_CAPSULE_FMP_HEADER=y +CONFIG_FLASH_CFI_MTD=y +CONFIG_CMD_DFU=y +CONFIG_DFU_TFTP=y +CONFIG_DFU_MTD=y +CONFIG_DFU_RAM=y +CONFIG_DFU_SF=y +CONFIG_DFU_SF_PART=y +CONFIG_FIT=y +CONFIG_OF_LIBFDT=y +CONFIG_CMD_ERASEENV=y
include/configs/synquacer.h +6 -0
@@ -61,6 +61,11 @@/* Since U-Boot 64bit PCIe support is limited, disable 64bit MMIO support */ /* #define CONFIG_SYS_PCI_64BIT 1 */ +#define DEFAULT_DFU_ALT_INFO "dfu_alt_info=" \ + "mtd nor1=u-boot.bin raw 200000 100000;" \ + "fip.bin raw 180000 78000;" \ + "optee.bin raw 500000 100000\0" +/* Distro boot settings */ #ifndef CONFIG_SPL_BUILD #ifdef CONFIG_CMD_USB
@@ -104,6 +109,7 @@"ramdisk_addr_r=0xa0000000\0" \"scriptaddr=0x88000000\0" \"pxefile_addr_r=0x88100000\0" \ +DEFAULT_DFU_ALT_INFO \ BOOTENV#endif /* __CONFIG_H */
PATCH v4 12/14 dfu_mtd: Ignore non-implemented lock device failure
In reply to Masami HiramatsuQuoted 10 lines · Masami Hiramatsu
Ignore the non-implemented lock device failure on writing mtd via DFU. Without this fix, DFU write shows an error on such device even if it succeeded, because
dfu->write_mediumreturns-EOPNOTSUPP.Signed-off-by Masami Hiramatsu <[email protected]>Cc Lukasz Majewski <[email protected]>--- drivers/dfu/dfu_mtd.c | 2 ++ 1 file changed, 2 insertions(+)
A patch has already been submitted for this[1].
Patrick, can you please apply this in your tree and send it as part of the next PR. Thanks.
-sughosh
[1] - https://lists.denx.de/pipermail/u-boot/2021-March/443896.html
Quoted 16 lines
drivers/dfu/dfu_mtd.c +2
-0@@ -152,6 +152,8 @@ static int mtd_block_op(enum dfu_op op, structdfu_entity *dfu, ret =mtd_lock (mtd, lock_ofs, lock_len);if (ret && ret != -EOPNOTSUPP )printf ("MTD device lock failed\n" ); +if (ret == -EOPNOTSUPP ) + ret =0 ; }return ret;}
PATCH v4 12/14 dfu_mtd: Ignore non-implemented lock device failure
Hi Sughosh,
2021?5?19?(?) 15:07 Sughosh Ganu <[email protected]>:
Quoted 9 lines · Masami Hiramatsu
Quoted 5 lines
Ignore the non-implemented lock device failure on writing mtd via DFU. Without this fix, DFU write shows an error on such device even if it succeeded, because
dfu->write_mediumreturns-EOPNOTSUPP.
Quoted 8 lines
Quoted 5 lines
Signed-off-by Masami Hiramatsu <[email protected]>Cc Lukasz Majewski <[email protected]>--- drivers/dfu/dfu_mtd.c | 2 ++ 1 file changed, 2 insertions(+)A patch has already been submitted for this[1].
Ah, thanks for pointing! If that is merged, I can drop this patch.
Thank you,
Quoted 23 lines
Patrick, can you please apply this in your tree and send it as part of the next PR. Thanks.
-sughosh
[1] - https://lists.denx.de/pipermail/u-boot/2021-March/443896.html
Quoted 15 lines
drivers/dfu/dfu_mtd.c +2
-0@@ -152,6 +152,8 @@ static int mtd_block_op(enum dfu_op op, struct dfu_entity *dfu, ret =mtd_lock (mtd, lock_ofs, lock_len);if (ret && ret != -EOPNOTSUPP )printf ("MTD device lock failed\n" ); +if (ret == -EOPNOTSUPP ) + ret =0 ; }return ret; }
Signature · 1 line
Masami Hiramatsu
Hi Masami,
Quoted 12 lines · Masami Hiramatsu
Hi,
Here is the 4th version of the series (including some fixes for build errors) to add SynQuacer/DeveloperBox 96board EE suport on U-Boot.
This series includes not only DeveloperBox support but also some fixes for the issues which I faced while porting U-Boot on the DeveloperBox. First 3 patches are fixes, next 1 patch is a code cleanup for generic gpio for arm. The next 7 patches adding DeveloperBox devices and board support. The last 3 patches are related to the UEFI capsule update (including bugfixes).
Quoted 5 lines
Previous version is here:
The default debug level is set to 7. I think it would be better to set it to something more reasonable for the final commit. Unfortunately I don't have time for a more detailed review, but I did manage to run this on my Synquacer and managed to run a full linux distro with EFI.
Quoted 140 lines
Changes in v4
-------------I dropped a PCI bugfix because it has been merged. And add I2C driver and enable RTC and EBBR support on the configuration.
[06/14]:
- Add Jaehoon's reviewed-by (Thanks!)
[09/14]:
- Add a new i2c driver.
[10/14]:
- Add i2c0 and RTC node.
[11/14]:
- Add I2C and RTC configuration.
- Enable RTC and Date command.
- Remove I2C0 node before booting linux to hide it same as EDK2 does.
- Add some configurations to make it EBBR compliant.
[14/14]:
- Add some config options for EBBR.BTW, should I split fixes from this series? (since I didn't expect this took so long...)
DeveloperBox
============DeveloperBox is a certified 96boards Enterprise Edition board. The board/SoC has: -
* Socionext SC2A11 24-cores ARM Cortex-A53 on tbe Mini-ATX form factor motherboard
* 4 DIMM slots (4GB DDR4-2400 UDIMM shipped by default)
* 1 4xPCIe Gen2 slot and 2 1xPCIe Gen2 slots
(1x slots are connected via PCIe bridge chip)
* 4 USB-3.0 ports
* 2 SATA ports
* 1 GbE network port
* 1 USB-UART serial port (micro USB)
* 64MB SPI NOR Flash
* 8GB eMMC Flash Storage
* 96boards LS connectorThe DeveloperBox schematic can be found here: -
https://www.96boards.org/documentation/enterprise/developerbox/hardware-docs/mzsc2am_v03_20180115_a.pdfAnd the other documents can be found here: -
https://www.96boards.org/documentation/enterprise/developerbox/Currently, the U-Boot port supports: -
* USB
* eMMC
* SPI-NOR
* SATA
* GbEThe DeveloperBox boots the TF-A and EDK2 as a main bootloader by default. The DeveloperBox U-Boot port will replace the EDK2 and boot from TF-A as BL33, but no need to combine with it.
Thank you,
---
Jassi Brar (4):
mmc: synquacer: Add SynQuacerF_SDH30SDHCI driver
spi: synquacer: Add HSSPI SPI controller driver for SynQuacer
net: synquacer: Add netsec driver
i2c: synquacer: SNI Synquacer I2C controllerMasami Hiramatsu (10):
ata: ahci-pci: Usescsi_opsto initialize ops
dm: pci: Skip setting VGA bridge bits if parent device is the host bus
efi: Fix to use null handle to create new handle forefi_fmp_raw
gpio: IntroduceCONFIG_GPIO_EXTRA_HEADERto cleanup #ifdefs
pci: synquacer: Add SynQuacer ECAM based PCIe driver
ARM: dts: synquacer: Add device trees for DeveloperBox
board: synquacer: Add DeveloperBox 96boards EE support
dfu_mtd: Ignore non-implemented lock device failure
doc: qemu: arm64: Fix the documentation of capsule update
configs: synquacer: Enable EFI capsule update supportarch/arm/Kconfig | 108 ++ arch/arm/dts/Makefile | 2 arch/arm/dts/synquacer-sc2a11-caches.dtsi | 73 + .../dts/synquacer-sc2a11-developerbox-u-boot.dtsi | 75 + arch/arm/dts/synquacer-sc2a11-developerbox.dts | 56 + arch/arm/dts/synquacer-sc2a11.dtsi | 595 ++++++++++ arch/arm/include/asm/gpio.h | 8 board/socionext/developerbox/Kconfig | 36 + board/socionext/developerbox/MAINTAINERS | 14 board/socionext/developerbox/Makefile | 9 board/socionext/developerbox/developerbox.c | 146 +++ configs/synquacer_developerbox_defconfig | 131 ++ doc/board/emulation/qemu_capsule_update.rst | 11 doc/board/index.rst | 1 doc/board/socionext/developerbox.rst | 87 ++ doc/board/socionext/index.rst | 9 drivers/ata/ahci-pci.c | 2 drivers/dfu/dfu_mtd.c | 2 drivers/i2c/Kconfig | 7 drivers/i2c/Makefile | 1 drivers/i2c/synquacer_i2c.c | 338 ++++++ drivers/mmc/Kconfig | 10 drivers/mmc/Makefile | 1 drivers/mmc/f_sdh30.c | 81 + drivers/net/Kconfig | 8 drivers/net/Makefile | 1 drivers/net/sni_netsec.c | 1134 ++++++++++++++++++++ drivers/pci/Kconfig | 12 drivers/pci/Makefile | 1 drivers/pci/pci-uclass.c | 3 drivers/pci/pcie_ecam_synquacer.c | 600 +++++++++++ drivers/spi/Kconfig | 8 drivers/spi/Makefile | 1 drivers/spi/spi-synquacer.c | 491 +++++++++ include/configs/synquacer.h | 115 ++ lib/efi_loader/efi_capsule.c | 2 36 files changed, 4162 insertions(+), 17 deletions(-) create mode 100644 arch/arm/dts/synquacer-sc2a11-caches.dtsi create mode 100644 arch/arm/dts/synquacer-sc2a11-developerbox-u-boot.dtsi create mode 100644 arch/arm/dts/synquacer-sc2a11-developerbox.dts create mode 100644 arch/arm/dts/synquacer-sc2a11.dtsi create mode 100644 board/socionext/developerbox/Kconfig create mode 100644 board/socionext/developerbox/MAINTAINERS create mode 100644 board/socionext/developerbox/Makefile create mode 100644 board/socionext/developerbox/developerbox.c create mode 100644 configs/synquacer_developerbox_defconfig create mode 100644 doc/board/socionext/developerbox.rst create mode 100644 doc/board/socionext/index.rst create mode 100644 drivers/i2c/synquacer_i2c.c create mode 100644 drivers/mmc/f_sdh30.c create mode 100644 drivers/net/sni_netsec.c create mode 100644 drivers/pci/pcie_ecam_synquacer.c create mode 100644 drivers/spi/spi-synquacer.c create mode 100644 include/configs/synquacer.h--
Masami Hiramatsu <[email protected]>
Hello Ilias,
2021年5月23日(日) 17:07 Ilias Apalodimas <[email protected]>:
Quoted 16 lines
Hi Masami,
Quoted 12 lines · Masami Hiramatsu
Hi,
Here is the 4th version of the series (including some fixes for build errors) to add SynQuacer/DeveloperBox 96board EE suport on U-Boot.
This series includes not only DeveloperBox support but also some fixes for the issues which I faced while porting U-Boot on the DeveloperBox. First 3 patches are fixes, next 1 patch is a code cleanup for generic gpio for arm. The next 7 patches adding DeveloperBox devices and board support. The last 3 patches are related to the UEFI capsule update (including bugfixes).
Quoted 8 lines
Quoted 5 lines
Previous version is here:
The default debug level is set to 7. I think it would be better to set it to something more reasonable for the final commit.
Yes, it was for the development value. It should be removed from defconfig at last, because it depends on the builder's choice.
Quoted 5 lines
Unfortunately I don't
have time for a more detailed review, but I did manage to run this on my Synquacer and managed to run a full linux distro with EFI.Tested-by Ilias Apalodimas <[email protected]>
Thanks for testing!
Thank you,
Quoted 139 lines
Quoted 139 lines
Changes in v4
-------------I dropped a PCI bugfix because it has been merged. And add I2C driver and enable RTC and EBBR support on the configuration.
[06/14]:
- Add Jaehoon's reviewed-by (Thanks!)
[09/14]:
- Add a new i2c driver.
[10/14]:
- Add i2c0 and RTC node.
[11/14]:
- Add I2C and RTC configuration.
- Enable RTC and Date command.
- Remove I2C0 node before booting linux to hide it same as EDK2 does.
- Add some configurations to make it EBBR compliant.
[14/14]:
- Add some config options for EBBR.BTW, should I split fixes from this series? (since I didn't expect this took so long...)
DeveloperBox
============DeveloperBox is a certified 96boards Enterprise Edition board. The board/SoC has: -
* Socionext SC2A11 24-cores ARM Cortex-A53 on tbe Mini-ATX form factor motherboard
* 4 DIMM slots (4GB DDR4-2400 UDIMM shipped by default)
* 1 4xPCIe Gen2 slot and 2 1xPCIe Gen2 slots
(1x slots are connected via PCIe bridge chip)
* 4 USB-3.0 ports
* 2 SATA ports
* 1 GbE network port
* 1 USB-UART serial port (micro USB)
* 64MB SPI NOR Flash
* 8GB eMMC Flash Storage
* 96boards LS connectorThe DeveloperBox schematic can be found here: -
https://www.96boards.org/documentation/enterprise/developerbox/hardware-docs/mzsc2am_v03_20180115_a.pdfAnd the other documents can be found here: -
https://www.96boards.org/documentation/enterprise/developerbox/Currently, the U-Boot port supports: -
* USB
* eMMC
* SPI-NOR
* SATA
* GbEThe DeveloperBox boots the TF-A and EDK2 as a main bootloader by default. The DeveloperBox U-Boot port will replace the EDK2 and boot from TF-A as BL33, but no need to combine with it.
Thank you,
---
Jassi Brar (4):
mmc: synquacer: Add SynQuacerF_SDH30SDHCI driver
spi: synquacer: Add HSSPI SPI controller driver for SynQuacer
net: synquacer: Add netsec driver
i2c: synquacer: SNI Synquacer I2C controllerMasami Hiramatsu (10):
ata: ahci-pci: Usescsi_opsto initialize ops
dm: pci: Skip setting VGA bridge bits if parent device is the host bus
efi: Fix to use null handle to create new handle forefi_fmp_raw
gpio: IntroduceCONFIG_GPIO_EXTRA_HEADERto cleanup #ifdefs
pci: synquacer: Add SynQuacer ECAM based PCIe driver
ARM: dts: synquacer: Add device trees for DeveloperBox
board: synquacer: Add DeveloperBox 96boards EE support
dfu_mtd: Ignore non-implemented lock device failure
doc: qemu: arm64: Fix the documentation of capsule update
configs: synquacer: Enable EFI capsule update supportarch/arm/Kconfig | 108 ++ arch/arm/dts/Makefile | 2 arch/arm/dts/synquacer-sc2a11-caches.dtsi | 73 + .../dts/synquacer-sc2a11-developerbox-u-boot.dtsi | 75 + arch/arm/dts/synquacer-sc2a11-developerbox.dts | 56 + arch/arm/dts/synquacer-sc2a11.dtsi | 595 ++++++++++ arch/arm/include/asm/gpio.h | 8 board/socionext/developerbox/Kconfig | 36 + board/socionext/developerbox/MAINTAINERS | 14 board/socionext/developerbox/Makefile | 9 board/socionext/developerbox/developerbox.c | 146 +++ configs/synquacer_developerbox_defconfig | 131 ++ doc/board/emulation/qemu_capsule_update.rst | 11 doc/board/index.rst | 1 doc/board/socionext/developerbox.rst | 87 ++ doc/board/socionext/index.rst | 9 drivers/ata/ahci-pci.c | 2 drivers/dfu/dfu_mtd.c | 2 drivers/i2c/Kconfig | 7 drivers/i2c/Makefile | 1 drivers/i2c/synquacer_i2c.c | 338 ++++++ drivers/mmc/Kconfig | 10 drivers/mmc/Makefile | 1 drivers/mmc/f_sdh30.c | 81 + drivers/net/Kconfig | 8 drivers/net/Makefile | 1 drivers/net/sni_netsec.c | 1134 ++++++++++++++++++++ drivers/pci/Kconfig | 12 drivers/pci/Makefile | 1 drivers/pci/pci-uclass.c | 3 drivers/pci/pcie_ecam_synquacer.c | 600 +++++++++++ drivers/spi/Kconfig | 8 drivers/spi/Makefile | 1 drivers/spi/spi-synquacer.c | 491 +++++++++ include/configs/synquacer.h | 115 ++ lib/efi_loader/efi_capsule.c | 2 36 files changed, 4162 insertions(+), 17 deletions(-) create mode 100644 arch/arm/dts/synquacer-sc2a11-caches.dtsi create mode 100644 arch/arm/dts/synquacer-sc2a11-developerbox-u-boot.dtsi create mode 100644 arch/arm/dts/synquacer-sc2a11-developerbox.dts create mode 100644 arch/arm/dts/synquacer-sc2a11.dtsi create mode 100644 board/socionext/developerbox/Kconfig create mode 100644 board/socionext/developerbox/MAINTAINERS create mode 100644 board/socionext/developerbox/Makefile create mode 100644 board/socionext/developerbox/developerbox.c create mode 100644 configs/synquacer_developerbox_defconfig create mode 100644 doc/board/socionext/developerbox.rst create mode 100644 doc/board/socionext/index.rst create mode 100644 drivers/i2c/synquacer_i2c.c create mode 100644 drivers/mmc/f_sdh30.c create mode 100644 drivers/net/sni_netsec.c create mode 100644 drivers/pci/pcie_ecam_synquacer.c create mode 100644 drivers/spi/spi-synquacer.c create mode 100644 include/configs/synquacer.h
Quoted 2 lines
Quoted 2 lines
--
Masami Hiramatsu <[email protected]>
--
Masami Hiramatsu
Re: [PATCH v4 12/14] dfu_mtd: Ignore non-implemented lock device failure
In reply to Sughosh GanuQuoted 13 lines · Sughosh Ganu
Quoted 10 lines · Masami Hiramatsu
Ignore the non-implemented lock device failure on writing mtd via DFU. Without this fix, DFU write shows an error on such device even if it succeeded, because
dfu->write_mediumreturns-EOPNOTSUPP.Signed-off-by Masami Hiramatsu <[email protected]>Cc Lukasz Majewski <[email protected]>--- drivers/dfu/dfu_mtd.c | 2 ++ 1 file changed, 2 insertions(+)
Quoted 4 lines
A patch has already been submitted for this[1].
Patrick, can you please apply this in your tree and send it as part of the next PR. Thanks.
Ok, I take the patch in my next PR
Quoted 23 lines
-sughosh
[1] - https://lists.denx.de/pipermail/u-boot/2021-March/443896.html
Quoted 16 lines
drivers/dfu/dfu_mtd.c +2
-0@@ -152,6 +152,8 @@ static int mtd_block_op(enum dfu_op op, structdfu_entity *dfu, ret =mtd_lock (mtd, lock_ofs, lock_len);if (ret && ret != -EOPNOTSUPP )printf ("MTD device lock failed\n" ); +if (ret == -EOPNOTSUPP ) + ret =0 ; }return ret;}