Add support for sc7280 WPSS PIL loading
v4 cover Add support for sc7280 WPSS PIL loading
Add support for PIL loading of WPSS co-processor for SC7280 SOCs.
Changes from v3:
- Add separate dt-bindings file for sc7280-wpss-pil
- Fix the handling of single power domains for adsp/cdsp from v3
Rakesh Pillai (2):
dt-bindings: remoteproc: qcom: Add SC7280 WPSS support
remoteproc: qcom: q6v5_wpss: Add support for sc7280 WPSS
.../bindings/remoteproc/qcom,sc7280-wpss-pil.yaml | 198 +++++++++++++++++++ drivers/remoteproc/qcom_q6v5_adsp.c | 209 +++++++++++++++++++-- 2 files changed, 392 insertions(+), 15 deletions(-) create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml
Signature · 1 line
2.7.4
PATCH v4 1/2 dt-bindings: remoteproc: qcom: Add SC7280 WPSS support
Add WPSS PIL loading support for SC7280 SoCs.
--- .../bindings/remoteproc/qcom,sc7280-wpss-pil.yaml | 198 +++++++++++++++++++++ 1 file changed, 198 insertions(+) create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +198 -0
@@ -0,0 +1,198 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/remoteproc/qcom,sc7280-wpss-pil.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SC7280 WPSS Peripheral Image Loader + +maintainers: + - Bjorn Andersson <[email protected]> + +description: + This document defines the binding for a component that loads and boots firmware + on the Qualcomm Technology Inc. WPSS. + +properties: + compatible: + enum: + - qcom,sc7280-wpss-pil + + reg: + maxItems: 1 + description: + The base address and size of the qdsp6ss register + + interrupts-extended: + minItems: 6 + items: + - description: Watchdog interrupt + - description: Fatal interrupt + - description: Ready interrupt + - description: Handover interrupt + - description: Stop acknowledge interrupt + - description: Shutdown acknowledge interrupt + + interrupt-names: + minItems: 6 + items: + - const: wdog + - const: fatal + - const: ready + - const: handover + - const: stop-ack + - const: shutdown-ack + + clocks: + minItems: 4 + items: + - description: GCC WPSS AHB BDG Master clock + - description: GCC WPSS AHB clock + - description: GCC WPSS RSCP clock + - description: XO clock + + clock-names: + minItems: 4 + items: + - const: gcc_wpss_ahb_bdg_mst_clk + - const: gcc_wpss_ahb_clk + - const: gcc_wpss_rscp_clk + - const: xo + + power-domains: + minItems: 2 + items: + - description: CX power domain + - description: MX power domain + + power-domain-names: + minItems: 2 + items: + - const: cx + - const: mx + + resets: + minItems: 2 + items: + - description: AOSS restart + - description: PDC SYNC + + reset-names: + minItems: 2 + items: + - const: restart + - const: pdc_sync + + memory-region: + maxItems: 1 + description: Reference to the reserved-memory for the Hexagon core + + qcom,halt-regs: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + Phandle reference to a syscon representing TCSR followed by the + three offsets within syscon for q6, modem and nc halt registers. + + qcom,qmp: + $ref: /schemas/types.yaml#/definitions/phandle + description: Reference to the AOSS side-channel message RAM. + + qcom,smem-states: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: States used by the AP to signal the Hexagon core + items: + - description: Stop the modem + + qcom,smem-state-names: + $ref: /schemas/types.yaml#/definitions/string-array + description: The names of the state bits used for SMP2P output + items: + - const: stop + + glink-edge: + type: object + description: + Qualcomm G-Link subnode which represents communication edge, channels + and devices related to the ADSP. + +required: + - compatible + - reg + - interrupts-extended + - interrupt-names + - clocks + - clock-names + - power-domains + - power-domain-names + - reset + - reset-names + - qcom,halt-regs + - memory-region + - qcom,qmp + - qcom,smem-states + - qcom,smem-state-names + - glink-edge + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,gcc-sc7280.h> + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/power/qcom-rpmpd.h> + #include <dt-bindings/reset/qcom,sdm845-aoss.h> + #include <dt-bindings/reset/qcom,sdm845-pdc.h> + #include <dt-bindings/mailbox/qcom-ipcc.h> + remoteproc@8a00000 { + compatible = "qcom,sc7280-wpss-pil"; + reg = <0x08a00000 0x10000>; + + interrupts-extended = <&intc GIC_SPI 587 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 7 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", "handover", + "stop-ack", "shutdown-ack"; + + clocks = <&gcc GCC_WPSS_AHB_BDG_MST_CLK>, + <&gcc GCC_WPSS_AHB_CLK>, + <&gcc GCC_WPSS_RSCP_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "gcc_wpss_ahb_bdg_mst_clk", + "gcc_wpss_ahb_clk", + "gcc_wpss_rscp_clk", + "xo"; + + power-domains = <&rpmhpd SC7280_CX>, + <&rpmhpd SC7280_MX>; + power-domain-names = "cx", "mx"; + + memory-region = <&wpss_mem>; + + qcom,qmp = <&aoss_qmp>; + + qcom,smem-states = <&wpss_smp2p_out 0>; + qcom,smem-state-names = "stop"; + + resets = <&aoss_reset AOSS_CC_WCSS_RESTART>, + <&pdc_reset PDC_WPSS_SYNC_RESET>; + reset-names = "restart", "pdc_sync"; + + qcom,halt-regs = <&tcsr_mutex 0x37000>; + + status = "disabled"; + + glink-edge { + interrupts-extended = <&ipcc IPCC_CLIENT_WPSS + IPCC_MPROC_SIGNAL_GLINK_QMP + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_WPSS + IPCC_MPROC_SIGNAL_GLINK_QMP>; + + label = "wpss"; + qcom,remote-pid = <13>; + }; + };
Signature · 1 line
2.7.4
Re: [PATCH v4 1/2] dt-bindings: remoteproc: qcom: Add SC7280 WPSS support
Quoting Rakesh Pillai (2021-09-17 03:35:40)
Quoted 14 lines
Add WPSS PIL loading support for SC7280 SoCs.
Signed-off-by Rakesh Pillai <[email protected]>--- .../bindings/remoteproc/qcom,sc7280-wpss-pil.yaml | 198 +++++++++++++++++++++ 1 file changed, 198 insertions(+) create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yamlDocumentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +0
-0
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml line 7
Quoted 7 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +7
-0@@ -0,0 +1,198 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/remoteproc/qcom,sc7280-wpss-pil.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SC7280 WPSS Peripheral Image Loader
Maybe spell out WPSS so we know what the acronym means?
Quoted 99 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +99
-0+ +maintainers: + - Bjorn Andersson <[email protected]> + +description: + This document defines the binding for a component that loads and boots firmware + on the Qualcomm Technology Inc. WPSS. + +properties: + compatible: + enum: + - qcom,sc7280-wpss-pil + + reg: + maxItems: 1 + description: + The base address and size of the qdsp6ss register + + interrupts-extended: + minItems: 6 + items: + - description: Watchdog interrupt + - description: Fatal interrupt + - description: Ready interrupt + - description: Handover interrupt + - description: Stop acknowledge interrupt + - description: Shutdown acknowledge interrupt + + interrupt-names: + minItems: 6 + items: + - const: wdog + - const: fatal + - const: ready + - const: handover + - const: stop-ack + - const: shutdown-ack + + clocks: + minItems: 4 + items: + - description: GCC WPSS AHB BDG Master clock + - description: GCC WPSS AHB clock + - description: GCC WPSS RSCP clock + - description: XO clock + + clock-names: + minItems: 4 + items: + - const: gcc_wpss_ahb_bdg_mst_clk + - const: gcc_wpss_ahb_clk + - const: gcc_wpss_rscp_clk + - const: xo + + power-domains: + minItems: 2 + items: + - description: CX power domain + - description: MX power domain + + power-domain-names: + minItems: 2 + items: + - const: cx + - const: mx + + resets: + minItems: 2 + items: + - description: AOSS restart + - description: PDC SYNC + + reset-names: + minItems: 2 + items: + - const: restart + - const: pdc_sync + + memory-region: + maxItems: 1 + description: Reference to the reserved-memory for the Hexagon core + + qcom,halt-regs: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + Phandle reference to a syscon representing TCSR followed by the + three offsets within syscon for q6, modem and nc halt registers. + + qcom,qmp: + $ref: /schemas/types.yaml#/definitions/phandle + description: Reference to the AOSS side-channel message RAM. + + qcom,smem-states: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: States used by the AP to signal the Hexagon core + items: + - description: Stop the modem + + qcom,smem-state-names:
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml line 116
Quoted 10 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +10
-0+ $ref: /schemas/types.yaml#/definitions/string-array + description: The names of the state bits used for SMP2P output + items: + - const: stop + + glink-edge: + type: object + description: + Qualcomm G-Link subnode which represents communication edge, channels + and devices related to the ADSP.
Are there any required properties of glink-edge? Or an empty node is all that's required? Maybe there's a binding that can be referenced here that describes the required properties?
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml line 122
Quoted 6 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +6
-0+ +required: + - compatible + - reg + - interrupts-extended + - interrupt-names
Why is interrupt-names required?
Quoted 54 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +54
-0+ - clocks + - clock-names + - power-domains + - power-domain-names + - reset + - reset-names + - qcom,halt-regs + - memory-region + - qcom,qmp + - qcom,smem-states + - qcom,smem-state-names + - glink-edge + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,gcc-sc7280.h> + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/power/qcom-rpmpd.h> + #include <dt-bindings/reset/qcom,sdm845-aoss.h> + #include <dt-bindings/reset/qcom,sdm845-pdc.h> + #include <dt-bindings/mailbox/qcom-ipcc.h> + remoteproc@8a00000 { + compatible = "qcom,sc7280-wpss-pil"; + reg = <0x08a00000 0x10000>; + + interrupts-extended = <&intc GIC_SPI 587 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 7 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", "handover", + "stop-ack", "shutdown-ack"; + + clocks = <&gcc GCC_WPSS_AHB_BDG_MST_CLK>, + <&gcc GCC_WPSS_AHB_CLK>, + <&gcc GCC_WPSS_RSCP_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "gcc_wpss_ahb_bdg_mst_clk", + "gcc_wpss_ahb_clk", + "gcc_wpss_rscp_clk", + "xo"; + + power-domains = <&rpmhpd SC7280_CX>, + <&rpmhpd SC7280_MX>; + power-domain-names = "cx", "mx"; + + memory-region = <&wpss_mem>; + + qcom,qmp = <&aoss_qmp>; +
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml line 186
Quoted 10 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +10
-0+ qcom,smem-states = <&wpss_smp2p_out 0>; + qcom,smem-state-names = "stop"; + + resets = <&aoss_reset AOSS_CC_WCSS_RESTART>, + <&pdc_reset PDC_WPSS_SYNC_RESET>; + reset-names = "restart", "pdc_sync"; + + qcom,halt-regs = <&tcsr_mutex 0x37000>; + + status = "disabled";
Can we remove status = "disabled" from the example? It provides no value.
Quoted 15 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +12
-1+ + glink-edge { + interrupts-extended = <&ipcc IPCC_CLIENT_WPSS + IPCC_MPROC_SIGNAL_GLINK_QMP + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_WPSS + IPCC_MPROC_SIGNAL_GLINK_QMP>; + + label = "wpss"; + qcom,remote-pid = <13>; + }; + }; --2.7.4
Re: [PATCH v4 1/2] dt-bindings: remoteproc: qcom: Add SC7280 WPSS support
In reply to Rakesh PillaiQuoted 8 lines · Rakesh Pillai
Add WPSS PIL loading support for SC7280 SoCs.
Signed-off-by Rakesh Pillai <[email protected]>--- .../bindings/remoteproc/qcom,sc7280-wpss-pil.yaml | 198 +++++++++++++++++++++ 1 file changed, 198 insertions(+) create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml
What happened to converting the existing binding? Given you already did that, please don't drop it.
Quoted 23 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +16
-0@@ -0,0 +1,198 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/remoteproc/qcom,sc7280-wpss-pil.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SC7280 WPSS Peripheral Image Loader + +maintainers: + - Bjorn Andersson <[email protected]> + +description: + This document defines the binding for a component that loads and boots firmware + on the Qualcomm Technology Inc. WPSS. + +properties:
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml line 26
Quoted 10 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +10
-0+ compatible: + enum: + - qcom,sc7280-wpss-pil + + reg: + maxItems: 1 + description: + The base address and size of the qdsp6ss register + + interrupts-extended:
Use 'interrupts'. The tooling supports either.
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml line 27
Quoted 1 line
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +1
-0+ minItems: 6
Don't need minItems unless it is less than 'items' length.
Quoted 22 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +22
-0+ items: + - description: Watchdog interrupt + - description: Fatal interrupt + - description: Ready interrupt + - description: Handover interrupt + - description: Stop acknowledge interrupt + - description: Shutdown acknowledge interrupt + + interrupt-names: + minItems: 6 + items: + - const: wdog + - const: fatal + - const: ready + - const: handover + - const: stop-ack + - const: shutdown-ack + + clocks: + minItems: 4 + items: + - description: GCC WPSS AHB BDG Master clock
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml line 59
Quoted 10 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +10
-0+ - description: GCC WPSS AHB clock + - description: GCC WPSS RSCP clock + - description: XO clock + + clock-names: + minItems: 4 + items: + - const: gcc_wpss_ahb_bdg_mst_clk + - const: gcc_wpss_ahb_clk + - const: gcc_wpss_rscp_clk
ahb_bdg, ahb, rscp is sufficient. Or use the same names as prior versions (did the h/w clocks change?).
Quoted 38 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +38
-0+ - const: xo + + power-domains: + minItems: 2 + items: + - description: CX power domain + - description: MX power domain + + power-domain-names: + minItems: 2 + items: + - const: cx + - const: mx + + resets: + minItems: 2 + items: + - description: AOSS restart + - description: PDC SYNC + + reset-names: + minItems: 2 + items: + - const: restart + - const: pdc_sync + + memory-region: + maxItems: 1 + description: Reference to the reserved-memory for the Hexagon core + + qcom,halt-regs: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + Phandle reference to a syscon representing TCSR followed by the + three offsets within syscon for q6, modem and nc halt registers. + + qcom,qmp: + $ref: /schemas/types.yaml#/definitions/phandle
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml line 107
Quoted 10 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +10
-0+ description: Reference to the AOSS side-channel message RAM. + + qcom,smem-states: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: States used by the AP to signal the Hexagon core + items: + - description: Stop the modem + + qcom,smem-state-names: + $ref: /schemas/types.yaml#/definitions/string-array
string or string-array?
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml line 110
Quoted 3 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +3
-0+ description: The names of the state bits used for SMP2P output + items: + - const: stop
This says only 1 entry, so 'string'.
Quoted 91 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-pil.yaml new file +88
-1+ + glink-edge: + type: object + description: + Qualcomm G-Link subnode which represents communication edge, channels + and devices related to the ADSP. + +required: + - compatible + - reg + - interrupts-extended + - interrupt-names + - clocks + - clock-names + - power-domains + - power-domain-names + - reset + - reset-names + - qcom,halt-regs + - memory-region + - qcom,qmp + - qcom,smem-states + - qcom,smem-state-names + - glink-edge + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,gcc-sc7280.h> + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/power/qcom-rpmpd.h> + #include <dt-bindings/reset/qcom,sdm845-aoss.h> + #include <dt-bindings/reset/qcom,sdm845-pdc.h> + #include <dt-bindings/mailbox/qcom-ipcc.h> + remoteproc@8a00000 { + compatible = "qcom,sc7280-wpss-pil"; + reg = <0x08a00000 0x10000>; + + interrupts-extended = <&intc GIC_SPI 587 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 7 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", "handover", + "stop-ack", "shutdown-ack"; + + clocks = <&gcc GCC_WPSS_AHB_BDG_MST_CLK>, + <&gcc GCC_WPSS_AHB_CLK>, + <&gcc GCC_WPSS_RSCP_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "gcc_wpss_ahb_bdg_mst_clk", + "gcc_wpss_ahb_clk", + "gcc_wpss_rscp_clk", + "xo"; + + power-domains = <&rpmhpd SC7280_CX>, + <&rpmhpd SC7280_MX>; + power-domain-names = "cx", "mx"; + + memory-region = <&wpss_mem>; + + qcom,qmp = <&aoss_qmp>; + + qcom,smem-states = <&wpss_smp2p_out 0>; + qcom,smem-state-names = "stop"; + + resets = <&aoss_reset AOSS_CC_WCSS_RESTART>, + <&pdc_reset PDC_WPSS_SYNC_RESET>; + reset-names = "restart", "pdc_sync"; + + qcom,halt-regs = <&tcsr_mutex 0x37000>; + + status = "disabled"; + + glink-edge { + interrupts-extended = <&ipcc IPCC_CLIENT_WPSS + IPCC_MPROC_SIGNAL_GLINK_QMP + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_WPSS + IPCC_MPROC_SIGNAL_GLINK_QMP>; + + label = "wpss"; + qcom,remote-pid = <13>; + }; + }; --2.7.4
RE: [PATCH v4 1/2] dt-bindings: remoteproc: qcom: Add SC7280 WPSS support
Quoted 27 lines
-----Original Message-----
From: Rob Herring <[email protected]>
Sent: Wednesday, September 22, 2021 10:59 PM
To: Rakesh Pillai <[email protected]>
Cc: Gross, Andy <[email protected]>; Bjorn Andersson <[email protected]>; Ohad Ben-Cohen <[email protected]>; Mathieu Poirier <[email protected]>; Philipp Zabel <[email protected]>; Stephen Boyd <[email protected]>; linux- arm-msm <[email protected]>; [email protected]; [email protected]; sibis <[email protected]>; [email protected]; [email protected]
Subject: Re: [PATCH v4 1/2] dt-bindings: remoteproc: qcom: Add SC7280 WPSS supportQuoted 10 lines · Rakesh Pillai
Add WPSS PIL loading support for SC7280 SoCs.
Signed-off-by Rakesh Pillai <[email protected]>--- .../bindings/remoteproc/qcom,sc7280-wpss-pil.yaml | 198 +++++++++++++++++++++ 1 file changed, 198 insertions(+) create mode 100644
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-
Quoted 4 lines
pil.yamlWhat happened to converting the existing binding? Given you already did that, please don't drop it.
Hi Rob,
Thanks for the review.
Sure, let me post v5 with other comments on this patch-series addressed. I will also include the yaml conversion for existing dt-bindings.
Thanks,
Rakesh Pillai.
Quoted 236 lines
Quoted 4 lines
diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-
pil.ya
Quoted 2 lines
ml b/Documentation/devicetree/bindings/remoteproc/qcom,sc7280-wpss-
pil.ya
Documentation/devicetree/bindings/remoteproc/qcom,sc7280-
Quoted 5 lines
ml
new file mode 100644
index 0000000..896d5f47Documentation/devicetree/bindings/remoteproc/qcom,sc7280- new file +0
-0wpss-pi
Quoted 19 lines
+++
l.yamlDocumentation/devicetree/bindings/remoteproc/qcom,sc7280- new file +17
-0@@ -0,0 +1,198 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 +--- +$id: +http://devicetree.org/schemas/remoteproc/qcom,sc7280-wpss-pil.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SC7280 WPSS Peripheral Image Loader + +maintainers: + - Bjorn Andersson <[email protected]> + +description: + This document defines the binding for a component that loads and +boots firmware + on the Qualcomm Technology Inc. WPSS. + +properties:Documentation/devicetree/bindings/remoteproc/qcom,sc7280- line 27
Quoted 10 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280- new file +10
-0+ compatible: + enum: + - qcom,sc7280-wpss-pil + + reg: + maxItems: 1 + description: + The base address and size of the qdsp6ss register + + interrupts-extended:Use 'interrupts'. The tooling supports either.
Documentation/devicetree/bindings/remoteproc/qcom,sc7280- line 28
Quoted 1 line
Documentation/devicetree/bindings/remoteproc/qcom,sc7280- new file +1
-0+ minItems: 6Don't need minItems unless it is less than 'items' length.
Quoted 22 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280- new file +22
-0+ items: + - description: Watchdog interrupt + - description: Fatal interrupt + - description: Ready interrupt + - description: Handover interrupt + - description: Stop acknowledge interrupt + - description: Shutdown acknowledge interrupt + + interrupt-names: + minItems: 6 + items: + - const: wdog + - const: fatal + - const: ready + - const: handover + - const: stop-ack + - const: shutdown-ack + + clocks: + minItems: 4 + items: + - description: GCC WPSS AHB BDG Master clockDocumentation/devicetree/bindings/remoteproc/qcom,sc7280- line 60
Quoted 10 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280- new file +10
-0+ - description: GCC WPSS AHB clock + - description: GCC WPSS RSCP clock + - description: XO clock + + clock-names: + minItems: 4 + items: + - const: gcc_wpss_ahb_bdg_mst_clk + - const: gcc_wpss_ahb_clk + - const: gcc_wpss_rscp_clk
ahb_bdg, ahb, rscp is sufficient. Or use the same names as prior versions (did the h/w clocks change?).Quoted 39 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280- new file +39
-0+ - const: xo + + power-domains: + minItems: 2 + items: + - description: CX power domain + - description: MX power domain + + power-domain-names: + minItems: 2 + items: + - const: cx + - const: mx + + resets: + minItems: 2 + items: + - description: AOSS restart + - description: PDC SYNC + + reset-names: + minItems: 2 + items: + - const: restart + - const: pdc_sync + + memory-region: + maxItems: 1 + description: Reference to the reserved-memory for the Hexagon + core + + qcom,halt-regs: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + Phandle reference to a syscon representing TCSR followed by the + three offsets within syscon for q6, modem and nc halt registers. + + qcom,qmp: + $ref: /schemas/types.yaml#/definitions/phandleDocumentation/devicetree/bindings/remoteproc/qcom,sc7280- line 109
Quoted 10 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280- new file +10
-0+ description: Reference to the AOSS side-channel message RAM. + + qcom,smem-states: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: States used by the AP to signal the Hexagon core + items: + - description: Stop the modem + + qcom,smem-state-names: + $ref: /schemas/types.yaml#/definitions/string-arraystring or string-array?
Documentation/devicetree/bindings/remoteproc/qcom,sc7280- line 112
Quoted 3 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280- new file +3
-0+ description: The names of the state bits used for SMP2P output + items: + - const: stopThis says only 1 entry, so 'string'.
Documentation/devicetree/bindings/remoteproc/qcom,sc7280- line 117
Quoted 5 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280- new file +5
-0+ + glink-edge: + type: object + description: + Qualcomm G-Link subnode which represents communication edge,channels
Quoted 86 lines
Documentation/devicetree/bindings/remoteproc/qcom,sc7280- new file +83
-1+ and devices related to the ADSP. + +required: + - compatible + - reg + - interrupts-extended + - interrupt-names + - clocks + - clock-names + - power-domains + - power-domain-names + - reset + - reset-names + - qcom,halt-regs + - memory-region + - qcom,qmp + - qcom,smem-states + - qcom,smem-state-names + - glink-edge + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,gcc-sc7280.h> + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/power/qcom-rpmpd.h> + #include <dt-bindings/reset/qcom,sdm845-aoss.h> + #include <dt-bindings/reset/qcom,sdm845-pdc.h> + #include <dt-bindings/mailbox/qcom-ipcc.h> + remoteproc@8a00000 { + compatible = "qcom,sc7280-wpss-pil"; + reg = <0x08a00000 0x10000>; + + interrupts-extended = <&intc GIC_SPI 587 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>, + <&wpss_smp2p_in 7 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", "handover", + "stop-ack", "shutdown-ack"; + + clocks = <&gcc GCC_WPSS_AHB_BDG_MST_CLK>, + <&gcc GCC_WPSS_AHB_CLK>, + <&gcc GCC_WPSS_RSCP_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "gcc_wpss_ahb_bdg_mst_clk", + "gcc_wpss_ahb_clk", + "gcc_wpss_rscp_clk", + "xo"; + + power-domains = <&rpmhpd SC7280_CX>, + <&rpmhpd SC7280_MX>; + power-domain-names = "cx", "mx"; + + memory-region = <&wpss_mem>; + + qcom,qmp = <&aoss_qmp>; + + qcom,smem-states = <&wpss_smp2p_out 0>; + qcom,smem-state-names = "stop"; + + resets = <&aoss_reset AOSS_CC_WCSS_RESTART>, + <&pdc_reset PDC_WPSS_SYNC_RESET>; + reset-names = "restart", "pdc_sync"; + + qcom,halt-regs = <&tcsr_mutex 0x37000>; + + status = "disabled"; + + glink-edge { + interrupts-extended = <&ipcc IPCC_CLIENT_WPSS + IPCC_MPROC_SIGNAL_GLINK_QMP + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_WPSS + IPCC_MPROC_SIGNAL_GLINK_QMP>; + + label = "wpss"; + qcom,remote-pid = <13>; + }; + }; --2.7.4
PATCH v4 2/2 remoteproc: qcom: q6v5_wpss: Add support for sc7280 WPSS
In reply to Rakesh PillaiAdd support for PIL loading of WPSS processor for SC7280
- WPSS boot will be requested by the wifi driver and hence disable auto-boot for WPSS.
- Add a separate shutdown sequence handler for WPSS.
- Add multiple power-domain voting support
--- drivers/remoteproc/qcom_q6v5_adsp.c | 209 +++++++++++++++++++++++++++++++++--- 1 file changed, 194 insertions(+), 15 deletions(-)
drivers/remoteproc/qcom_q6v5_adsp.c +194 -15
@@ -32,6 +32,7 @@/* time out value */ #define ACK_TIMEOUT 1000 +#define ACK_TIMEOUT_US 1000000#define BOOT_FSM_TIMEOUT 10000/* mask values */ #define EVB_MASK GENMASK(27, 4)
@@ -51,6 +52,8 @@#define QDSP6SS_CORE_CBCR 0x20#define QDSP6SS_SLEEP_CBCR 0x3c +#define QCOM_Q6V5_RPROC_PROXY_PD_MAX 3 +struct adsp_pil_data {int crash_reason_smem;const char *firmware_name;
@@ -58,9 +61,13 @@ struct adsp_pil_data {const char *ssr_name;const char *sysmon_name;int ssctl_id; +bool is_wpss; +bool auto_boot;const char **clk_ids;int num_clks; +const char **proxy_pd_names; +const char *load_state; };struct qcom_adsp {
@@ -93,11 +100,143 @@ struct qcom_adsp {void *mem_region;size_t mem_size; +struct device *proxy_pds[QCOM_Q6V5_RPROC_PROXY_PD_MAX ]; +int proxy_pd_count; +struct qcom_rproc_glink glink_subdev;struct qcom_rproc_ssr ssr_subdev;struct qcom_sysmon *sysmon; + +int (*shutdown)(struct qcom_adsp *adsp); }; +static int qcom_rproc_pds_attach (struct device *dev,struct device **devs, +const char **pd_names) +{ +size_t num_pds =0 ; +int ret; +int i; + +if (!pd_names) +return 0 ; + +/* Handle single power domain */ +if (dev->pm_domain) { + devs[0 ] = dev; +pm_runtime_enable (dev); +return 1 ; + } + +while (pd_names[num_pds]) + num_pds++; + +for (i =0 ; i < num_pds; i++) { + devs[i] =dev_pm_domain_attach_by_name (dev, pd_names[i]); +if (IS_ERR_OR_NULL (devs[i])) { + ret =PTR_ERR (devs[i]) ? : -ENODATA ; + goto unroll_attach; + } + } + +return num_pds; + +unroll_attach: +for (i--; i >=0 ; i--) +dev_pm_domain_detach (devs[i], false); + +return ret; +} + +static void qcom_rproc_pds_detach (struct qcom_adsp *adsp,struct device **pds, +size_t pd_count) +{ +struct device *dev = adsp->dev; +int i; + +/* Handle single power domain */ +if (dev->pm_domain && pd_count) { +pm_runtime_disable (dev); +return ; + } + +for (i =0 ; i < pd_count; i++) +dev_pm_domain_detach (pds[i], false); +} + +static int qcom_rproc_pds_enable (struct qcom_adsp *adsp,struct device **pds, +size_t pd_count) +{ +int ret; +int i; + +for (i =0 ; i < pd_count; i++) { +dev_pm_genpd_set_performance_state (pds[i],INT_MAX ); + ret =pm_runtime_get_sync (pds[i]); +if (ret <0 ) { +pm_runtime_put_noidle (pds[i]); +dev_pm_genpd_set_performance_state (pds[i],0 ); + goto unroll_pd_votes; + } + } + +return 0 ; + +unroll_pd_votes: +for (i--; i >=0 ; i--) { +dev_pm_genpd_set_performance_state (pds[i],0 ); +pm_runtime_put (pds[i]); + } + +return ret; +} + +static void qcom_rproc_pds_disable (struct qcom_adsp *adsp,struct device **pds, +size_t pd_count) +{ +int i; + +for (i =0 ; i < pd_count; i++) { +dev_pm_genpd_set_performance_state (pds[i],0 ); +pm_runtime_put (pds[i]); + } +} + +static int qcom_wpss_shutdown (struct qcom_adsp *adsp) +{ +unsigned int val; + +regmap_write (adsp->halt_map, adsp->halt_lpass +LPASS_HALTREQ_REG ,1 ); + +/* Wait for halt ACK from QDSP6 */ +regmap_read_poll_timeout (adsp->halt_map, + adsp->halt_lpass +LPASS_HALTACK_REG , val, + val,1000 ,ACK_TIMEOUT_US ); + +/* Assert the WPSS PDC Reset */ +reset_control_assert (adsp->pdc_sync_reset); +/* Place the WPSS processor into reset */ +reset_control_assert (adsp->restart); +/* wait after asserting subsystem restart from AOSS */ +usleep_range (200 ,205 ); +/* Remove the WPSS reset */ +reset_control_deassert (adsp->restart); +/* De-assert the WPSS PDC Reset */ +reset_control_deassert (adsp->pdc_sync_reset); + +usleep_range (100 ,105 ); + +clk_bulk_disable_unprepare (adsp->num_clks, adsp->clks); + +regmap_write (adsp->halt_map, adsp->halt_lpass +LPASS_HALTREQ_REG ,0 ); + +/* Wait for halt ACK from QDSP6 */ +regmap_read_poll_timeout (adsp->halt_map, + adsp->halt_lpass +LPASS_HALTACK_REG , val, + !val,1000 ,ACK_TIMEOUT_US ); + +return 0 ; +} +static int qcom_adsp_shutdown (struct qcom_adsp *adsp) {unsigned long timeout;
@@ -193,12 +332,10 @@ static int adsp_start(struct rproc *rproc)if (ret) goto disable_irqs; -dev_pm_genpd_set_performance_state (adsp->dev,INT_MAX ); - ret =pm_runtime_get_sync (adsp->dev); -if (ret) { -pm_runtime_put_noidle (adsp->dev); + ret =qcom_rproc_pds_enable (adsp, adsp->proxy_pds, + adsp->proxy_pd_count); +if (ret <0 ) goto disable_xo_clk; - } ret =clk_bulk_prepare_enable (adsp->num_clks, adsp->clks);if (ret) {
@@ -243,8 +380,7 @@ static int adsp_start(struct rproc *rproc) disable_adsp_clks:clk_bulk_disable_unprepare (adsp->num_clks, adsp->clks); disable_power_domain: -dev_pm_genpd_set_performance_state (adsp->dev,0 ); -pm_runtime_put (adsp->dev); +qcom_rproc_pds_disable (adsp, adsp->proxy_pds, adsp->proxy_pd_count); disable_xo_clk:clk_disable_unprepare (adsp->xo); disable_irqs:
@@ -258,8 +394,7 @@ static void qcom_adsp_pil_handover(struct qcom_q6v5 *q6v5) struct qcom_adsp *adsp = container_of(q6v5, struct qcom_adsp, q6v5);clk_disable_unprepare (adsp->xo); -dev_pm_genpd_set_performance_state (adsp->dev,0 ); -pm_runtime_put (adsp->dev); +qcom_rproc_pds_disable (adsp, adsp->proxy_pds, adsp->proxy_pd_count); }static int adsp_stop (struct rproc *rproc)
@@ -272,7 +407,7 @@ static int adsp_stop(struct rproc *rproc)if (ret == -ETIMEDOUT )dev_err (adsp->dev,"timed out on wait\n" ); - ret =qcom_adsp_shutdown (adsp); + ret = adsp->shutdown (adsp);if (ret)dev_err (adsp->dev,"failed to shutdown: %d\n" , ret);
@@ -441,6 +576,8 @@ static int adsp_probe(struct platform_device *pdev)dev_err (&pdev->dev,"unable to allocate remoteproc\n" );return -ENOMEM ; } + + rproc->auto_boot = desc->auto_boot;rproc_coredump_set_elf_info (rproc,ELFCLASS32 ,EM_NONE ); adsp = (struct qcom_adsp *)rproc->priv;
@@ -449,6 +586,11 @@ static int adsp_probe(struct platform_device *pdev) adsp->info_name = desc->sysmon_name;platform_set_drvdata (pdev, adsp); +if (desc->is_wpss) + adsp->shutdown = qcom_wpss_shutdown; +else + adsp->shutdown = qcom_adsp_shutdown; + ret =adsp_alloc_memory_region (adsp);if (ret) goto free_rproc;
@@ -457,7 +599,13 @@ static int adsp_probe(struct platform_device *pdev)if (ret) goto free_rproc; -pm_runtime_enable (adsp->dev); + ret =qcom_rproc_pds_attach (adsp->dev, adsp->proxy_pds, + desc->proxy_pd_names); +if (ret <0 ) { +dev_err (&pdev->dev,"Failed to attach proxy power domains\n" ); + goto free_rproc; + } + adsp->proxy_pd_count = ret; ret =adsp_init_reset (adsp);if (ret)
@@ -467,8 +615,8 @@ static int adsp_probe(struct platform_device *pdev)if (ret) goto disable_pm; - ret =qcom_q6v5_init (&adsp->q6v5, pdev, rproc, desc->crash_reason_smem,NULL , - qcom_adsp_pil_handover); + ret =qcom_q6v5_init (&adsp->q6v5, pdev, rproc, desc->crash_reason_smem, + desc->load_state, qcom_adsp_pil_handover);if (ret) goto disable_pm;
@@ -489,7 +637,8 @@ static int adsp_probe(struct platform_device *pdev)return 0 ; disable_pm: -pm_runtime_disable (adsp->dev); +qcom_rproc_pds_detach (adsp, adsp->proxy_pds, adsp->proxy_pd_count); + free_rproc:rproc_free (rproc);
@@ -506,7 +655,7 @@ static int adsp_remove(struct platform_device *pdev)qcom_remove_glink_subdev (adsp->rproc, &adsp->glink_subdev);qcom_remove_sysmon_subdev (adsp->sysmon);qcom_remove_ssr_subdev (adsp->rproc, &adsp->ssr_subdev); -pm_runtime_disable (adsp->dev); +qcom_rproc_pds_detach (adsp, adsp->proxy_pds, adsp->proxy_pd_count);rproc_free (adsp->rproc);return 0 ;
@@ -518,11 +667,16 @@ static const struct adsp_pil_data adsp_resource_init = { .ssr_name = "lpass", .sysmon_name = "adsp", .ssctl_id = 0x14, + .is_wpss = false, + .auto_boot = true, .clk_ids = (const char *[]) {"sway_cbcr" ,"lpass_ahbs_aon_cbcr" ,"lpass_ahbm_aon_cbcr" ,"qdsp6ss_xo" ,"qdsp6ss_sleep" ,"qdsp6ss_core" ,NULL }, .num_clks = 7, + .proxy_pd_names = (const char *[]) { +"cx" ,NULL + }, };static const struct adsp_pil_data cdsp_resource_init = {
@@ -531,15 +685,40 @@ static const struct adsp_pil_data cdsp_resource_init = { .ssr_name = "cdsp", .sysmon_name = "cdsp", .ssctl_id = 0x17, + .is_wpss = false, + .auto_boot = true, .clk_ids = (const char *[]) {"sway" ,"tbu" ,"bimc" ,"ahb_aon" ,"q6ss_slave" ,"q6ss_master" ,"q6_axim" ,NULL }, .num_clks = 7, + .proxy_pd_names = (const char *[]) { +"cx" ,NULL + }, +}; + +static const struct adsp_pil_data wpss_resource_init = { + .crash_reason_smem =626 , + .firmware_name ="wpss.mdt" , + .ssr_name ="wpss" , + .sysmon_name ="wpss" , + .ssctl_id =0x19 , + .is_wpss = true, + .auto_boot = false, + .load_state ="wpss" , + .clk_ids = (const char *[]) { +"gcc_wpss_ahb_bdg_mst_clk" ,"gcc_wpss_ahb_clk" , +"gcc_wpss_rscp_clk" ,NULL + }, + .num_clks =3 , + .proxy_pd_names = (const char *[]) { +"cx" ,"mx" ,NULL + }, };static const struct of_device_id adsp_of_match[] = { { .compatible ="qcom,qcs404-cdsp-pil" , .data = &cdsp_resource_init }, + { .compatible ="qcom,sc7280-wpss-pil" , .data = &wpss_resource_init }, { .compatible ="qcom,sdm845-adsp-pil" , .data = &adsp_resource_init }, { }, };
Signature · 1 line
2.7.4