Skip to contentSkip to conversation

performance differences: "maxcpus=1" vs. "echo 0 > /sys/devices/system/cpu/cpu1/online"

DISCUSSION Michael Meyer 8 participants 17 messages Mar 25, 2008 – Apr 2, 2008

lore
Share & tools
lore
#0 lore raw

Hi,

what is the difference between booting a dual core machine with "maxcpus=1" or by deactivating the second core at run time with "echo 0 > /sys/devices/system/cpu/cpu1/online"?

I observed a funny behaviour of apache ant: although it uses javac which is single threaded, a compile run with "maxcpus=1" is actually faster than a compile run with both cores activated. But with the second core deactivated using "echo 0 > /sys/devices/system/cpu/cpu1/online" it is even slower than with both cores.

Is here any method to get the exact same behaviour of "maxcpus=1" with disabling the second core only temporarily? So that the second core could be disabled before the ant execution and enabled after the ant execution?

Thanks a lot!

E-Mails jetzt auf Ihrem Handy.
www.yahoo.de/go

#1 lore raw
Quoted 6 lines · Michael Meyer

Hi,

what is the difference between booting a dual core machine with "maxcpus=1" or by deactivating the second core at run time with "echo 0 > /sys/devices/system/cpu/cpu1/online"?

maxcpus=1 should turn off the SMP alternative and switch to UP only, optimising some locks and instructions.

Signature · 2 lines
Luciano Rocha <[email protected]>
Eurotux Informática, S.A. <http://www.eurotux.com/>
#2 lore raw
Quoted 7 lines · --- Luciano Rocha
Quoted 4 lines · Michael Meyer

Hi,

what is the difference between booting a dual core machine with "maxcpus=1" or by deactivating the

Quoted 7 lines

second

Quoted 2 lines

core at run time with "echo 0 >
/sys/devices/system/cpu/cpu1/online"?

maxcpus=1 should turn off the SMP alternative and
switch to UP only,
optimising some locks and instructions.

Can this be achieved during runtime also? And is it possible to switch back to SMP after that?

Lesen Sie Ihre E-Mails jetzt einfach von unterwegs.
www.yahoo.de/go

#3 lore raw
In reply to Luciano Rocha
Quoted 10 lines · Luciano Rocha
Quoted 6 lines · Michael Meyer

Hi,

what is the difference between booting a dual core machine with "maxcpus=1" or by deactivating the second core at run time with "echo 0 > /sys/devices/system/cpu/cpu1/online"?

maxcpus=1 should turn off the SMP alternative and switch to UP only, optimising some locks and instructions.

CPU hot unplug will do the same. But it is unlikely it accounts for that much performance difference.

If he used maxcpus=0 it would make sense. maxcpus=0 disables the IO-APIC which likely makes a large difference. But it should be actually slower.

There should be actually no difference in theory between max_cpus=1 and hot unplug to one CPU. Might be some bug.

-Andi

#4 lore raw
Quoted 27 lines · --- Andi Kleen
Quoted 1 line · Luciano Rocha

On Tue, Mar 25, 2008 at 02:47:50PM +0100, Michael

Quoted 3 lines · Meyer
Quoted 3 lines

Hi,

what is the difference between booting a dual

core

Quoted 1 line
Quoted 1 line

machine with "maxcpus=1" or by deactivating the

second

Quoted 4 lines
Quoted 2 lines

core at run time with "echo 0 >
/sys/devices/system/cpu/cpu1/online"?

maxcpus=1 should turn off the SMP alternative and

switch to UP only,

Quoted 1 line

optimising some locks and instructions.

CPU hot unplug will do the same. But it is unlikely it accounts
for that much performance difference.

If he used maxcpus=0 it would make sense. maxcpus=0 disables
the IO-APIC which likely makes a large difference. But it should
be actually slower.

Quoted 3 lines

There should be actually no difference in theory
between max_cpus=1
and hot unplug to one CPU. Might be some bug.

I had the following time values:

maxcpus=1:
real 0m1.642s
user 0m1.528s
sys 0m0.068s

maxcpus=2 and
echo 1 > /sys/devices/system/cpu/cpu1/online:
real 0m2.579s
user 0m4.096s
sys 0m0.160s

maxcpus=2 and
echo 0 > /sys/devices/system/cpu/cpu1/online:
real 0m3.757s
user 0m3.632s
sys 0m0.112s

Lesen Sie Ihre E-Mails jetzt einfach von unterwegs.
www.yahoo.de/go

#5 lore raw
Quoted 48 lines · Michael Meyer
Quoted 27 lines · --- Andi Kleen
Quoted 1 line · Luciano Rocha

On Tue, Mar 25, 2008 at 02:47:50PM +0100, Michael

Quoted 3 lines · Meyer
Quoted 3 lines

Hi,

what is the difference between booting a dual

core

Quoted 1 line
Quoted 1 line

machine with "maxcpus=1" or by deactivating the

second

Quoted 4 lines
Quoted 2 lines

core at run time with "echo 0 >
/sys/devices/system/cpu/cpu1/online"?

maxcpus=1 should turn off the SMP alternative and

switch to UP only,

Quoted 1 line

optimising some locks and instructions.

CPU hot unplug will do the same. But it is unlikely it accounts
for that much performance difference.

If he used maxcpus=0 it would make sense. maxcpus=0 disables
the IO-APIC which likely makes a large difference. But it should
be actually slower.

Quoted 3 lines

There should be actually no difference in theory
between max_cpus=1
and hot unplug to one CPU. Might be some bug.

I had the following time values:

maxcpus=1:

 real    0m1.642s
 user    0m1.528s
 sys     0m0.068s

maxcpus=2 and
echo 1 > /sys/devices/system/cpu/cpu1/online:

 real    0m2.579s
 user    0m4.096s
 sys     0m0.160s
Quoted 7 lines

maxcpus=2 and
echo 0 > /sys/devices/system/cpu/cpu1/online:

 real    0m3.757s
 user    0m3.632s
 sys     0m0.112s

What kind of CPU are you using? Some Intel CPU's do "funny stuff", like dynamically overclocking itself when working on a single thread, or using all of the 2nd level cache instead of sharing it with the second core.

Regards,
Wander Winkelhorst.

#6 lore raw
Quoted 4 lines

What kind of CPU are you using? Some Intel CPU's do "funny stuff", like dynamically overclocking itself when working on a single thread, or using all of the 2nd level cache instead of sharing it with the second core.

P0 should also work fine with cpu hotplug. At least in theory.

-Andi

#7 lore raw
In reply to Wander Winkelhorst

--- Wander Winkelhorst <[email protected]>

Quoted 74 lines · schrieb:
Quoted 7 lines · Michael Meyer
Quoted 3 lines · --- Andi Kleen
Quoted 1 line · Luciano Rocha

On Tue, Mar 25, 2008 at 02:47:50PM +0100,

Michael

Quoted 4 lines
Quoted 4 lines
Quoted 3 lines · Meyer
Quoted 3 lines

Hi,

what is the difference between booting a

dual

Quoted 2 lines
Quoted 2 lines

core

Quoted 1 line
Quoted 1 line

machine with "maxcpus=1" or by deactivating

the

Quoted 5 lines
Quoted 5 lines

second

Quoted 4 lines
Quoted 2 lines

core at run time with "echo 0 >
/sys/devices/system/cpu/cpu1/online"?

maxcpus=1 should turn off the SMP alternative

and

Quoted 4 lines
Quoted 4 lines

switch to UP only,

Quoted 1 line

optimising some locks and instructions.

CPU hot unplug will do the same. But it is

unlikely

Quoted 4 lines
Quoted 4 lines

it accounts
for that much performance difference.

If he used maxcpus=0 it would make sense.

maxcpus=0

Quoted 2 lines
Quoted 2 lines

disables
the IO-APIC which likely makes a large

difference.

Quoted 4 lines
Quoted 4 lines

But it should
be actually slower.

There should be actually no difference in

theory

Quoted 16 lines
Quoted 2 lines

between max_cpus=1
and hot unplug to one CPU. Might be some bug.

I had the following time values:

maxcpus=1:

 real    0m1.642s
 user    0m1.528s
 sys     0m0.068s

maxcpus=2 and
echo 1 > /sys/devices/system/cpu/cpu1/online:

 real    0m2.579s
 user    0m4.096s
 sys     0m0.160s
Quoted 7 lines

maxcpus=2 and
echo 0 > /sys/devices/system/cpu/cpu1/online:

 real    0m3.757s
 user    0m3.632s
 sys     0m0.112s

What kind of CPU are you using? Some Intel CPU's do "funny stuff",
like dynamically overclocking itself when working on a single thread,
or using all of the 2nd level cache instead of sharing it with the
second core.

Quoted 3 lines

Regards,
Wander Winkelhorst.

Intel Core 2 Duo E6600 (2.4 Ghz). I do not think that it is capable of dynamically overclocking.

$ cat /proc/cpuinfo 
processor	: 0
vendor_id	: GenuineIntel
cpu family	: 6
model		: 15
model name	: Intel(R) Core(TM)2 CPU          6600  @
2.40GHz
stepping	: 6
cpu MHz		: 1600.000
cache size	: 4096 KB
physical id	: 0
siblings	: 2
core id		: 0
cpu cores	: 2
fdiv_bug	: no
hlt_bug		: no
f00f_bug	: no
coma_bug	: no
fpu		: yes
fpu_exception	: yes
cpuid level	: 10
wp		: yes
flags		: fpu vme de pse tsc msr pae mce cx8 apic sep
mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr
sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon
pebs bts pni monitor ds_cpl vmx est tm2 ssse3 cx16
xtpr lahf_lm
bogomips	: 4791.87
clflush size	: 64

processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 15
model name : Intel(R) Core(TM)2 CPU 6600 @
2.40GHz
stepping : 6
cpu MHz : 1600.000
cache size : 4096 KB
physical id : 0
siblings : 2
core id : 1
cpu cores : 2
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 10
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep
mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr lahf_lm
bogomips : 4788.35
clflush size : 64

E-Mails jetzt auf Ihrem Handy.
www.yahoo.de/go

#8 lore raw
In reply to Michael Meyer
Quoted 41 lines · Michael Meyer
Quoted 27 lines · --- Andi Kleen
Quoted 1 line · Luciano Rocha

On Tue, Mar 25, 2008 at 02:47:50PM +0100, Michael

Quoted 3 lines · Meyer
Quoted 3 lines

Hi,

what is the difference between booting a dual

core

Quoted 1 line
Quoted 1 line

machine with "maxcpus=1" or by deactivating the

second

Quoted 4 lines
Quoted 2 lines

core at run time with "echo 0 >
/sys/devices/system/cpu/cpu1/online"?

maxcpus=1 should turn off the SMP alternative and

switch to UP only,

Quoted 1 line

optimising some locks and instructions.

CPU hot unplug will do the same. But it is unlikely it accounts
for that much performance difference.

If he used maxcpus=0 it would make sense. maxcpus=0 disables
the IO-APIC which likely makes a large difference. But it should
be actually slower.

Quoted 3 lines

There should be actually no difference in theory
between max_cpus=1
and hot unplug to one CPU. Might be some bug.

I had the following time values:

maxcpus=1:
real 0m1.642s
user 0m1.528s
sys 0m0.068s

Quoted 5 lines

maxcpus=2 and
echo 1 > /sys/devices/system/cpu/cpu1/online:
real 0m2.579s
user 0m4.096s
sys 0m0.160s

this above is the baseline, yes?
it is same as if you used no boot param
and did not touch the online file, yes?

Quoted 5 lines

maxcpus=2 and
echo 0 > /sys/devices/system/cpu/cpu1/online:
real 0m3.757s
user 0m3.632s
sys 0m0.112s

Please post the contents of

# grep . /sys/devices/system/cpu/cpu*/cpufreq/*
and also
grep . /proc/acpi/processor/*/power

My guess that the maxcpus=1 case benefits from turbo mode, aka EIDA. That benefit, however, is subject to this bug:
http://bugzilla.kernel.org/show_bug.cgi?id=5471
because for a single thread to run faster than the marketing MHz, the other thread must be in deep-idle, which is prevented by the bug above.

If your scaling_available_frequencies includes 2401000 then you probably have a turbo-mode enabled processor.

one way to verify this would be to disable turbo mode by pegging the MHz like so:

# echo 2400000 > /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq
# echo 2400000 > /sys/devices/system/cpu/cpu1/cpufreq/cpuinfo_max_freq

-Len

#9 lore raw
Quoted 42 lines · --- Len Brown
Quoted 41 lines · Michael Meyer
Quoted 27 lines · --- Andi Kleen
Quoted 1 line · Luciano Rocha

On Tue, Mar 25, 2008 at 02:47:50PM +0100, Michael

Quoted 3 lines · Meyer
Quoted 3 lines

Hi,

what is the difference between booting a dual

core

Quoted 1 line
Quoted 1 line

machine with "maxcpus=1" or by deactivating the

second

Quoted 4 lines
Quoted 2 lines

core at run time with "echo 0 >
/sys/devices/system/cpu/cpu1/online"?

maxcpus=1 should turn off the SMP alternative and

switch to UP only,

Quoted 1 line

optimising some locks and instructions.

CPU hot unplug will do the same. But it is unlikely it accounts
for that much performance difference.

If he used maxcpus=0 it would make sense. maxcpus=0 disables
the IO-APIC which likely makes a large difference. But it should
be actually slower.

Quoted 3 lines

There should be actually no difference in theory
between max_cpus=1
and hot unplug to one CPU. Might be some bug.

I had the following time values:

maxcpus=1:
real 0m1.642s
user 0m1.528s
sys 0m0.068s

Quoted 7 lines
Quoted 5 lines

maxcpus=2 and
echo 1 > /sys/devices/system/cpu/cpu1/online:
real 0m2.579s
user 0m4.096s
sys 0m0.160s

this above is the baseline, yes?

Yes, it is.

Quoted 2 lines

it is same as if you used no boot param
and did not touch the online file, yes?

Yes. I just repeated it - once without the commands and once with the same commands stated above. Same result. So this is the default.

Quoted 9 lines
Quoted 6 lines

maxcpus=2 and
echo 0 > /sys/devices/system/cpu/cpu1/online:
real 0m3.757s
user 0m3.632s
sys 0m0.112s

Please post the contents of

# grep . /sys/devices/system/cpu/cpu*/cpufreq/*
# grep . /sys/devices/system/cpu/cpu*/cpufreq/*
/sys/devices/system/cpu/cpu0/cpufreq/affected_cpus:0
/sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq:2400000
/sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_min_freq:1600000
/sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies:2400000
1600000 
/sys/devices/system/cpu/cpu0/cpufreq/scaling_available_governors:ondemand
userspace conservative powersave performance 
/sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq:1600000
/sys/devices/system/cpu/cpu0/cpufreq/scaling_driver:acpi-cpufreq
/sys/devices/system/cpu/cpu0/cpufreq/scaling_governor:ondemand
/sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq:2400000
/sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq:1600000
/sys/devices/system/cpu/cpu1/cpufreq/affected_cpus:1
/sys/devices/system/cpu/cpu1/cpufreq/cpuinfo_max_freq:2400000
/sys/devices/system/cpu/cpu1/cpufreq/cpuinfo_min_freq:1600000
/sys/devices/system/cpu/cpu1/cpufreq/scaling_available_frequencies:2400000
1600000 
/sys/devices/system/cpu/cpu1/cpufreq/scaling_available_governors:ondemand
userspace conservative powersave performance 
/sys/devices/system/cpu/cpu1/cpufreq/scaling_cur_freq:1600000
/sys/devices/system/cpu/cpu1/cpufreq/scaling_driver:acpi-cpufreq
/sys/devices/system/cpu/cpu1/cpufreq/scaling_governor:ondemand
/sys/devices/system/cpu/cpu1/cpufreq/scaling_max_freq:2400000
/sys/devices/system/cpu/cpu1/cpufreq/scaling_min_freq:1600000
Quoted 2 lines

and also
grep . /proc/acpi/processor/*/power

# grep . /proc/acpi/processor/*/power
/proc/acpi/processor/CPU0/power:active state:            C0
/proc/acpi/processor/CPU0/power:max_cstate:              C8
/proc/acpi/processor/CPU0/power:bus master activity:     00000000
/proc/acpi/processor/CPU0/power:maximum allowed latency: 8000 usec
/proc/acpi/processor/CPU0/power:states:
/proc/acpi/processor/CPU0/power:    C1:                  type[C1]
promotion[--] demotion[--] latency[000] usage[00000000]
duration[00000000000000000000]
/proc/acpi/processor/CPU1/power:active state:            C0
/proc/acpi/processor/CPU1/power:max_cstate:              C8
/proc/acpi/processor/CPU1/power:bus master activity:     00000000
/proc/acpi/processor/CPU1/power:maximum allowed latency: 8000 usec
/proc/acpi/processor/CPU1/power:states:
/proc/acpi/processor/CPU1/power:    C1:                  type[C1]
promotion[--] demotion[--] latency[000] usage[00000000]
duration[00000000000000000000]
Quoted 10 lines

My guess that the maxcpus=1 case benefits from turbo mode, aka EIDA. That benefit, however, is subject to this bug:
http://bugzilla.kernel.org/show_bug.cgi?id=5471
because for a single thread to run faster than the marketing MHz, the other thread must be in deep-idle, which is prevented by the bug above.

If your scaling_available_frequencies includes 2401000 then you probably have a turbo-mode enabled processor.

It does not include 2401000. The processor is an Intel Core 2 Duo E6600 (2.4GHZ) bought at the beginning of 2007. I do not think that that kind of freqency scaling was available back than.

Quoted 11 lines

one way to verify this would be to disable turbo mode by pegging the MHz like so:

# echo 2400000 >
/sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq
# echo 2400000 >
/sys/devices/system/cpu/cpu1/cpufreq/cpuinfo_max_freq

-Len

This does not work, as both are read-only.

E-Mails jetzt auf Ihrem Handy.
www.yahoo.de/go

#10 lore raw
In reply to Andi Kleen
Quoted 16 lines · Andi Kleen
Quoted 10 lines · Luciano Rocha
Quoted 6 lines · Michael Meyer

Hi,

what is the difference between booting a dual core machine with "maxcpus=1" or by deactivating the second core at run time with "echo 0 > /sys/devices/system/cpu/cpu1/online"?

maxcpus=1 should turn off the SMP alternative and switch to UP only, optimising some locks and instructions.

CPU hot unplug will do the same. But it is unlikely it accounts for that much performance difference.

Quoted 6 lines

If he used maxcpus=0 it would make sense. maxcpus=0 disables the IO-APIC which likely makes a large difference. But it should be actually slower.

There should be actually no difference in theory between max_cpus=1 and hot unplug to one CPU. Might be some bug.

Or thermal effect. I'd expect that behaviour with bad cooling.

Pavel

Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
#11 lore raw
In reply to Michael Meyer
Quoted 6 lines · Michael Meyer

Hi,

what is the difference between booting a dual core machine with "maxcpus=1" or by deactivating the second core at run time with "echo 0 > /sys/devices/system/cpu/cpu1/online"?

maxcpus=1 : core stays powered off
0 > online : core enters halt.

Quoted 7 lines

I observed a funny behaviour of apache ant: although it uses javac which is single threaded, a compile run with "maxcpus=1" is actually faster than a compile run with both cores activated. But with the second core deactivated using "echo 0 > /sys/devices/system/cpu/cpu1/online" it is even slower than with both cores.

Thermal fun? Check cooling.

Quoted 5 lines

Is here any method to get the exact same behaviour of "maxcpus=1" with disabling the second core only temporarily? So that the second core could be disabled before the ant execution and enabled after the ant execution?

Patch pushing 0 > online cores into C4 would be nice.

Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
#12 lore raw
Quoted 19 lines · --- Pavel Machek
Quoted 6 lines · Michael Meyer

Hi,

what is the difference between booting a dual core machine with "maxcpus=1" or by deactivating the second core at run time with "echo 0 > /sys/devices/system/cpu/cpu1/online"?

maxcpus=1 : core stays powered off
0 > online : core enters halt.

Quoted 7 lines

I observed a funny behaviour of apache ant: although it uses javac which is single threaded, a compile run with "maxcpus=1" is actually faster than a compile run with both cores activated. But with the second core deactivated using "echo 0 > /sys/devices/system/cpu/cpu1/online" it is even slower than with both cores.

Quoted 1 line

Thermal fun? Check cooling.

I have an extremely well cooled case and a Thermaltake Typhoon sitting on the E6600 (Intel TDP 65 Watt). At a room temperature of 20°C both cores idle at 21°C and after one hour of two instances of prime95 running they are both at 28-33°C. As the E6600 is specified until 60°C (I believe), this should prevent any thermal throttling?

Quoted 6 lines
Quoted 5 lines

Is here any method to get the exact same behaviour of "maxcpus=1" with disabling the second core only temporarily? So that the second core could be disabled before the ant execution and enabled after the ant execution?

Quoted 12 lines

Patch pushing 0 > online cores into C4 would be nice.

Signature · 9 lines
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures)
http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
--
To unsubscribe from this list: send the line "unsubscribe
linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

E-Mails jetzt auf Ihrem Handy.
www.yahoo.de/go

#13 lore raw

Hi!

Quoted 16 lines
Quoted 16 lines
Quoted 4 lines

what is the difference between booting a dual core machine with "maxcpus=1" or by deactivating the second core at run time with "echo 0 > /sys/devices/system/cpu/cpu1/online"?

maxcpus=1 : core stays powered off
0 > online : core enters halt.

Quoted 7 lines

I observed a funny behaviour of apache ant: although it uses javac which is single threaded, a compile run with "maxcpus=1" is actually faster than a compile run with both cores activated. But with the second core deactivated using "echo 0 > /sys/devices/system/cpu/cpu1/online" it is even slower than with both cores.

Quoted 7 lines
Quoted 1 line

Thermal fun? Check cooling.

I have an extremely well cooled case and a Thermaltake Typhoon sitting on the E6600 (Intel TDP 65 Watt). At a room temperature of 20°C both cores idle at 21°C and after one hour of two instances of prime95 running they are both at 28-33°C. As the E6600 is specified until 60°C (I believe), this should prevent any thermal throttling?

Ok, and your chip is too old to have "Enhanced Dynamic Acceleration Technology" (Intel, can't you use some reasonable names?!)... both would explain effects you see, and it is neither...

You could try implementing deep sleep (C4) state for cpu hotplug....
Pavel

Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
#14 lore raw
Quoted 24 lines · --- Pavel Machek

Hi!

Quoted 16 lines
Quoted 16 lines
Quoted 4 lines

what is the difference between booting a dual core machine with "maxcpus=1" or by deactivating the second core at run time with "echo 0 > /sys/devices/system/cpu/cpu1/online"?

maxcpus=1 : core stays powered off
0 > online : core enters halt.

Quoted 7 lines

I observed a funny behaviour of apache ant: although it uses javac which is single threaded, a compile run with "maxcpus=1" is actually faster than a compile run with both cores activated. But with the second core deactivated using "echo 0 > /sys/devices/system/cpu/cpu1/online" it is even slower than with both cores.

Quoted 3 lines
Quoted 1 line

Thermal fun? Check cooling.

I have an extremely well cooled case and a Thermaltake Typhoon

sitting

Quoted 1 line

on the E6600 (Intel TDP 65 Watt). At a room temperature of 20°C

both

Quoted 8 lines
Quoted 2 lines

cores idle at 21°C and after one hour of two instances of prime95 running they are both at 28-33°C. As the E6600 is specified until

60°C

Quoted 1 line

(I believe), this should prevent any thermal throttling?

Ok, and your chip is too old to have "Enhanced Dynamic Acceleration Technology" (Intel, can't you use some reasonable names?!)... both would explain effects you see, and it is neither...

It is too old to have that. I bought it at the beginning of 2007 and it is from the first line of Core 2 Duo processors (released in summer 2006). I think "Enhanced Dynamic Acceleration Technology" is only available recently.

Quoted 1 line

You could try implementing deep sleep (C4) state for cpu hotplug....

I have to confess that I sneaked unto LKML illegitimately, as I am not a kernel hacker.

But thank you all very much for all the hints!

Lesen Sie Ihre E-Mails jetzt einfach von unterwegs.
www.yahoo.de/go

#15 lore raw

Hi!

Quoted 9 lines
Quoted 3 lines

Ok, and your chip is too old to have "Enhanced Dynamic Acceleration Technology" (Intel, can't you use some reasonable names?!)... both would explain effects you see, and it is neither...

It is too old to have that. I bought it at the beginning of 2007 and it is from the first line of Core 2 Duo processors (released in summer 2006). I think "Enhanced Dynamic Acceleration Technology" is only available recently.

Quoted 4 lines
Quoted 1 line

You could try implementing deep sleep (C4) state for cpu hotplug....

I have to confess that I sneaked unto LKML illegitimately, as I am not a kernel hacker.

You can still play one, and submit a patch. Over internet, noone can tell if you are hacker or not ;-). I would be happy to help with good advice ;-).
Pavel

Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
#16 lore raw
In reply to Michael Meyer
Quoted 2 lines · In article <[email protected]> you wrote:

Is here any method to get the exact same behaviour of "maxcpus=1" with disabling the second core only

I dont have much insight, but I do remember some java performance problems on Multi-Core with some Dell Desktops. I think they had been fixed with a Bios upgrade. Sorry I dont remeber the chip and revision details anymore. I just felt reminded, because MAXCPU=1 helped back then, also.

Gruss
Bernd
y