Linux 5.15.15

index 76cd09879eaf..a81d6c43b9b6 100644
@@ -312,6 +312,10 @@ int arch_kexec_apply_relocations_add(struct purgatory_info *pi,
 		addr = section->sh_addr + relas[i].r_offset;
 
 		r_type = ELF64_R_TYPE(relas[i].r_info);
+
+		if (r_type == R_390_PLT32DBL)
+			r_type = R_390_PC32DBL;
+
 		ret = arch_kexec_do_relocs(r_type, loc, val, addr);
 		if (ret) {
 			pr_err("Unknown rela relocation: %d\n", r_type);

index 5a321b4076aa..cab93935cc7f 100644
@@ -628,6 +628,9 @@ static int bfusb_probe(struct usb_interface *intf, const struct usb_device_id *i
 	data->bulk_out_ep   = bulk_out_ep->desc.bEndpointAddress;
 	data->bulk_pkt_size = le16_to_cpu(bulk_out_ep->desc.wMaxPacketSize);
 
+	if (!data->bulk_pkt_size)
+		goto done;
+
 	rwlock_init(&data->lock);
 
 	data->reassembly = NULL;

69 lines not on this page · raw message

index f1705b46fc88..525be2e1fbb2 100644
@@ -2193,8 +2193,15 @@ static int btintel_setup_combined(struct hci_dev *hdev)
 	 * As a workaround, send HCI Reset command first which will reset the
 	 * number of completed commands and allow normal command processing
 	 * from now on.
+	 *
+	 * Regarding the INTEL_BROKEN_SHUTDOWN_LED flag, these devices maybe
+	 * in the SW_RFKILL ON state as a workaround of fixing LED issue during
+	 * the shutdown() procedure, and once the device is in SW_RFKILL ON
+	 * state, the only way to exit out of it is sending the HCI_Reset
+	 * command.
 	 */
-	if (btintel_test_flag(hdev, INTEL_BROKEN_INITIAL_NCMD)) {
+	if (btintel_test_flag(hdev, INTEL_BROKEN_INITIAL_NCMD) ||
+	    btintel_test_flag(hdev, INTEL_BROKEN_SHUTDOWN_LED)) {
 		skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL,
 				     HCI_INIT_TIMEOUT);
 		if (IS_ERR(skb)) {

@@ -2263,12 +2270,6 @@ static int btintel_setup_combined(struct hci_dev *hdev)
 				set_bit(HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED,
 					&hdev->quirks);
 
-			/* These devices have an issue with LED which doesn't
-			 * go off immediately during shutdown. Set the flag
-			 * here to send the LED OFF command during shutdown.
-			 */
-			btintel_set_flag(hdev, INTEL_BROKEN_LED);
-
 			err = btintel_legacy_rom_setup(hdev, &ver);
 			break;
 		case 0x0b:      /* SfP */

@@ -2399,9 +2400,10 @@ static int btintel_shutdown_combined(struct hci_dev *hdev)
 
 	/* Some platforms have an issue with BT LED when the interface is
 	 * down or BT radio is turned off, which takes 5 seconds to BT LED
-	 * goes off. This command turns off the BT LED immediately.
+	 * goes off. As a workaround, sends HCI_Intel_SW_RFKILL to put the
+	 * device in the RFKILL ON state which turns off the BT LED immediately.
 	 */
-	if (btintel_test_flag(hdev, INTEL_BROKEN_LED)) {
+	if (btintel_test_flag(hdev, INTEL_BROKEN_SHUTDOWN_LED)) {
 		skb = __hci_cmd_sync(hdev, 0xfc3f, 0, NULL, HCI_INIT_TIMEOUT);
 		if (IS_ERR(skb)) {
 			ret = PTR_ERR(skb);

index aa64072bbe68..704e3b7bcb77 100644
@@ -145,7 +145,7 @@ enum {
 	INTEL_FIRMWARE_FAILED,
 	INTEL_BOOTING,
 	INTEL_BROKEN_INITIAL_NCMD,
-	INTEL_BROKEN_LED,
+	INTEL_BROKEN_SHUTDOWN_LED,
 	INTEL_ROM_LEGACY,
 
 	__INTEL_NUM_FLAGS,

150 lines not on this page · raw message

185 lines not on this page · raw message

index a725792d5248..7f0964645d0c 100644
@@ -3063,9 +3063,9 @@ static void snb_wm_latency_quirk(struct drm_i915_private *dev_priv)
 	 * The BIOS provided WM memory latency values are often
 	 * inadequate for high resolution displays. Adjust them.
 	 */
-	changed = ilk_increase_wm_latency(dev_priv, dev_priv->wm.pri_latency, 12) |
-		ilk_increase_wm_latency(dev_priv, dev_priv->wm.spr_latency, 12) |
-		ilk_increase_wm_latency(dev_priv, dev_priv->wm.cur_latency, 12);
+	changed = ilk_increase_wm_latency(dev_priv, dev_priv->wm.pri_latency, 12);
+	changed |= ilk_increase_wm_latency(dev_priv, dev_priv->wm.spr_latency, 12);
+	changed |= ilk_increase_wm_latency(dev_priv, dev_priv->wm.cur_latency, 12);
 
 	if (!changed)
 		return;

index c4bc67024534..9a791d8ef200 100644
@@ -2194,7 +2194,6 @@ int uvc_register_video_device(struct uvc_device *dev,
 			      const struct v4l2_file_operations *fops,
 			      const struct v4l2_ioctl_ops *ioctl_ops)
 {
-	const char *name;
 	int ret;
 
 	/* Initialize the video buffers queue. */

@@ -2223,20 +2222,16 @@ int uvc_register_video_device(struct uvc_device *dev,
 	case V4L2_BUF_TYPE_VIDEO_CAPTURE:
 	default:
 		vdev->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING;
-		name = "Video Capture";
 		break;
 	case V4L2_BUF_TYPE_VIDEO_OUTPUT:
 		vdev->device_caps = V4L2_CAP_VIDEO_OUTPUT | V4L2_CAP_STREAMING;
-		name = "Video Output";
 		break;
 	case V4L2_BUF_TYPE_META_CAPTURE:
 		vdev->device_caps = V4L2_CAP_META_CAPTURE | V4L2_CAP_STREAMING;
-		name = "Metadata";
 		break;
 	}
 
-	snprintf(vdev->name, sizeof(vdev->name), "%s %u", name,
-		 stream->header.bTerminalLink);
+	strscpy(vdev->name, dev->name, sizeof(vdev->name));
 
 	/*
 	 * Set the driver data before calling video_register_device, otherwise

index 3f1d976eb67c..f2ea6540a01e 100644
@@ -136,6 +136,7 @@ static int intel_lpss_acpi_probe(struct platform_device *pdev)
 {
 	struct intel_lpss_platform_info *info;
 	const struct acpi_device_id *id;
+	int ret;
 
 	id = acpi_match_device(intel_lpss_acpi_ids, &pdev->dev);
 	if (!id)

@@ -149,10 +150,14 @@ static int intel_lpss_acpi_probe(struct platform_device *pdev)
 	info->mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	info->irq = platform_get_irq(pdev, 0);
 
+	ret = intel_lpss_probe(&pdev->dev, info);
+	if (ret)
+		return ret;
+
 	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);
 
-	return intel_lpss_probe(&pdev->dev, info);
+	return 0;
 }
 
 static int intel_lpss_acpi_remove(struct platform_device *pdev)

index d0f2edfe296c..c2b26ada104d 100644
@@ -1951,6 +1951,7 @@ static const struct pci_device_id pci_ids[] = {
 	SDHCI_PCI_DEVICE(INTEL, JSL_SD,    intel_byt_sd),
 	SDHCI_PCI_DEVICE(INTEL, LKF_EMMC,  intel_glk_emmc),
 	SDHCI_PCI_DEVICE(INTEL, LKF_SD,    intel_byt_sd),
+	SDHCI_PCI_DEVICE(INTEL, ADL_EMMC,  intel_glk_emmc),
 	SDHCI_PCI_DEVICE(O2, 8120,     o2),
 	SDHCI_PCI_DEVICE(O2, 8220,     o2),
 	SDHCI_PCI_DEVICE(O2, 8221,     o2),

index 8f90c4163bb5..dcd99d5057ee 100644
@@ -59,6 +59,7 @@
 #define PCI_DEVICE_ID_INTEL_JSL_SD	0x4df8
 #define PCI_DEVICE_ID_INTEL_LKF_EMMC	0x98c4
 #define PCI_DEVICE_ID_INTEL_LKF_SD	0x98f8
+#define PCI_DEVICE_ID_INTEL_ADL_EMMC	0x54c4
 
 #define PCI_DEVICE_ID_SYSKONNECT_8000	0x8000
 #define PCI_DEVICE_ID_VIA_95D0		0x95d0

index 5e892bef46b0..8dcdd5162ecf 100644
@@ -321,7 +321,7 @@ static void gs_usb_receive_bulk_callback(struct urb *urb)
 
 	/* device reports out of range channel id */
 	if (hf->channel >= GS_MAX_INTF)
-		goto resubmit_urb;
+		goto device_detach;
 
 	dev = usbcan->canch[hf->channel];
 

@@ -406,6 +406,7 @@ static void gs_usb_receive_bulk_callback(struct urb *urb)
 
 	/* USB failure take down all interfaces */
 	if (rc == -ENODEV) {
+ device_detach:
 		for (rc = 0; rc < GS_MAX_INTF; rc++) {
 			if (usbcan->canch[rc])
 				netif_device_detach(usbcan->canch[rc]->netdev);

@@ -507,6 +508,8 @@ static netdev_tx_t gs_can_start_xmit(struct sk_buff *skb,
 
 	hf->echo_id = idx;
 	hf->channel = dev->channel;
+	hf->flags = 0;
+	hf->reserved = 0;
 
 	cf = (struct can_frame *)skb->data;
 

index 2acdb8ad6c71..ecbc09cbe259 100644
@@ -342,7 +342,6 @@ static netdev_tx_t veth_xmit(struct sk_buff *skb, struct net_device *dev)
 		 */
 		use_napi = rcu_access_pointer(rq->napi) &&
 			   veth_skb_is_eligible_for_gro(dev, rcv, skb);
-		skb_record_rx_queue(skb, rxq);
 	}
 
 	skb_tx_timestamp(skb);

index 99c0b81e496b..c22ec921b2e9 100644
@@ -2051,7 +2051,7 @@ int ath11k_wmi_send_scan_start_cmd(struct ath11k *ar,
 	void *ptr;
 	int i, ret, len;
 	u32 *tmp_ptr;
-	u8 extraie_len_with_pad = 0;
+	u16 extraie_len_with_pad = 0;
 	struct hint_short_ssid *s_ssid = NULL;
 	struct hint_bssid *hint_bssid = NULL;
 

@@ -2070,7 +2070,7 @@ int ath11k_wmi_send_scan_start_cmd(struct ath11k *ar,
 		len += sizeof(*bssid) * params->num_bssid;
 
 	len += TLV_HDR_SIZE;
-	if (params->extraie.len)
+	if (params->extraie.len && params->extraie.len <= 0xFFFF)
 		extraie_len_with_pad =
 			roundup(params->extraie.len, sizeof(u32));
 	len += extraie_len_with_pad;

@@ -2177,7 +2177,7 @@ int ath11k_wmi_send_scan_start_cmd(struct ath11k *ar,
 		      FIELD_PREP(WMI_TLV_LEN, len);
 	ptr += TLV_HDR_SIZE;
 
-	if (params->extraie.len)
+	if (extraie_len_with_pad)
 		memcpy(ptr, params->extraie.ptr,
 		       params->extraie.len);
 

index 13f8cf70b9ae..41a2a026f156 100644
@@ -106,6 +106,13 @@ static const struct dmi_system_id button_array_table[] = {
 			DMI_MATCH(DMI_PRODUCT_NAME, "Surface Go 3"),
 		},
 	},
+	{
+		.ident = "Microsoft Surface Go 3",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Surface Go 3"),
+		},
+	},
 	{ }
 };
 

128 lines not on this page · raw message

index b33e34cce12e..f9a8cdd9a168 100644
@@ -74,6 +74,7 @@ void DeInitLed871x(struct LED_871x *pLed)
 	_cancel_workitem_sync(&pLed->BlinkWorkItem);
 	_cancel_timer_ex(&pLed->BlinkTimer);
 	ResetLedStatus(pLed);
+	SwLedOff(pLed->padapter, pLed);
 }
 
 /*  */

index 8c8524679ba3..0d869b5e309c 100644
@@ -3778,18 +3778,18 @@ static void hfa384x_usb_throttlefn(struct timer_list *t)
 
 	spin_lock_irqsave(&hw->ctlxq.lock, flags);
 
-	/*
-	 * We need to check BOTH the RX and the TX throttle controls,
-	 * so we use the bitwise OR instead of the logical OR.
-	 */
 	pr_debug("flags=0x%lx\n", hw->usb_flags);
-	if (!hw->wlandev->hwremoved &&
-	    ((test_and_clear_bit(THROTTLE_RX, &hw->usb_flags) &&
-	      !test_and_set_bit(WORK_RX_RESUME, &hw->usb_flags)) |
-	     (test_and_clear_bit(THROTTLE_TX, &hw->usb_flags) &&
-	      !test_and_set_bit(WORK_TX_RESUME, &hw->usb_flags))
-	    )) {
-		schedule_work(&hw->usb_work);
+	if (!hw->wlandev->hwremoved) {
+		bool rx_throttle = test_and_clear_bit(THROTTLE_RX, &hw->usb_flags) &&
+				   !test_and_set_bit(WORK_RX_RESUME, &hw->usb_flags);
+		bool tx_throttle = test_and_clear_bit(THROTTLE_TX, &hw->usb_flags) &&
+				   !test_and_set_bit(WORK_TX_RESUME, &hw->usb_flags);
+		/*
+		 * We need to check BOTH the RX and the TX throttle controls,
+		 * so we use the bitwise OR instead of the logical OR.
+		 */
+		if (rx_throttle | tx_throttle)
+			schedule_work(&hw->usb_work);
 	}
 
 	spin_unlock_irqrestore(&hw->ctlxq.lock, flags);

index 00d35fe1fef0..16bab9826127 100644
@@ -753,6 +753,7 @@ void usb_hcd_poll_rh_status(struct usb_hcd *hcd)
 {
 	struct urb	*urb;
 	int		length;
+	int		status;
 	unsigned long	flags;
 	char		buffer[6];	/* Any root hubs with > 31 ports? */
 

@@ -770,11 +771,17 @@ void usb_hcd_poll_rh_status(struct usb_hcd *hcd)
 		if (urb) {
 			clear_bit(HCD_FLAG_POLL_PENDING, &hcd->flags);
 			hcd->status_urb = NULL;
+			if (urb->transfer_buffer_length >= length) {
+				status = 0;
+			} else {
+				status = -EOVERFLOW;
+				length = urb->transfer_buffer_length;
+			}
 			urb->actual_length = length;
 			memcpy(urb->transfer_buffer, buffer, length);
 
 			usb_hcd_unlink_urb_from_ep(hcd, urb);
-			usb_hcd_giveback_urb(hcd, urb, 0);
+			usb_hcd_giveback_urb(hcd, urb, status);
 		} else {
 			length = 0;
 			set_bit(HCD_FLAG_POLL_PENDING, &hcd->flags);

index 00070a8a6507..3bc4a86c3d0a 100644
@@ -1225,7 +1225,7 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type)
 			 */
 			if (portchange || (hub_is_superspeed(hub->hdev) &&
 						port_resumed))
-				set_bit(port1, hub->change_bits);
+				set_bit(port1, hub->event_bits);
 
 		} else if (udev->persist_enabled) {
 #ifdef CONFIG_PM

84 lines not on this page · raw message

index b80415011dcd..9ce46cb8564d 100644
@@ -246,6 +246,15 @@ enum {
 	 * HCI after resume.
 	 */
 	HCI_QUIRK_NO_SUSPEND_NOTIFIER,
+
+	/*
+	 * When this quirk is set, LE tx power is not queried on startup
+	 * and the min/max tx power values default to HCI_TX_POWER_INVALID.
+	 *
+	 * This quirk can be set before hci_register_dev is called or
+	 * during the hdev->setup vendor callback.
+	 */
+	HCI_QUIRK_BROKEN_READ_TRANSMIT_POWER,
 };
 
 /* HCI device flags */

index 93c3a332e853..b84e63d62b8a 100644
@@ -7039,16 +7039,16 @@ static int adjust_ptr_min_max_vals(struct bpf_verifier_env *env,
 		fallthrough;
 	case PTR_TO_PACKET_END:
 	case PTR_TO_SOCKET:
-	case PTR_TO_SOCKET_OR_NULL:
 	case PTR_TO_SOCK_COMMON:
-	case PTR_TO_SOCK_COMMON_OR_NULL:
 	case PTR_TO_TCP_SOCK:
-	case PTR_TO_TCP_SOCK_OR_NULL:
 	case PTR_TO_XDP_SOCK:
+reject:
 		verbose(env, "R%d pointer arithmetic on %s prohibited\n",
 			dst, reg_type_str[ptr_reg->type]);
 		return -EACCES;
 	default:
+		if (reg_type_may_be_null(ptr_reg->type))
+			goto reject;
 		break;
 	}
 

index 76988f39ed5a..3f4d27668576 100644
@@ -867,8 +867,17 @@ void wq_worker_running(struct task_struct *task)
 
 	if (!worker->sleeping)
 		return;
+
+	/*
+	 * If preempted by unbind_workers() between the WORKER_NOT_RUNNING check
+	 * and the nr_running increment below, we may ruin the nr_running reset
+	 * and leave with an unexpected pool->nr_running == 1 on the newly unbound
+	 * pool. Protect against such race.
+	 */
+	preempt_disable();
 	if (!(worker->flags & WORKER_NOT_RUNNING))
 		atomic_inc(&worker->pool->nr_running);
+	preempt_enable();
 	worker->sleeping = 0;
 }
 

index 8a47a3017d61..325db9c4c610 100644
@@ -742,7 +742,8 @@ static int hci_init3_req(struct hci_request *req, unsigned long opt)
 			hci_req_add(req, HCI_OP_LE_READ_ADV_TX_POWER, 0, NULL);
 		}
 
-		if (hdev->commands[38] & 0x80) {
+		if ((hdev->commands[38] & 0x80) &&
+		    !test_bit(HCI_QUIRK_BROKEN_READ_TRANSMIT_POWER, &hdev->quirks)) {
 			/* Read LE Min/Max Tx Power*/
 			hci_req_add(req, HCI_OP_LE_READ_TRANSMIT_POWER,
 				    0, NULL);

index df6968b28bf4..02cbcb2ecf0d 100644
@@ -119,8 +119,8 @@ enum {
 };
 
 struct tpcon {
-	int idx;
-	int len;
+	unsigned int idx;
+	unsigned int len;
 	u32 state;
 	u8 bs;
 	u8 sn;