dw_mmc: fix DW MMC cores with 32-bit bus on 64-bit Linux systems
cover dw_mmc: fix DW MMC cores with 32-bit bus on 64-bit Linux systems
DesignWare MMC cores have a configurable data bus width of either 16, 32, or 64 bytes. It is possible, and some vendors actually do it, to ship a DW MMC core configured for 32-bit data bus within a 64-bit SoC. In this case the kernel will attempt 64-bit (readq) accesses to certain 64-bit MMIO registers, while the core will expect pairs of 32-bit accesses.
It seems that currently the only register for which the kernel performs 64-bit accesses is the FIFO. The symptom is that the DW MMC core never receives a read on the second half of the register, does not register the datum as being read, and thus not advancing its internal FIFO pointer, breaking further reads. It also seems that this FIFO is only used for small (less than 16 bytes) transfers, which probably means that only some SDIO cards are affected.
Sergey Lisov (2):
devicetree: synopsys-dw-mshc-common: add "fifo-access-32bit" property
dw_mmc: add an option to force 32-bit accesses to 64-bit device
registers
.../bindings/mmc/synopsys-dw-mshc-common.yaml | 6 + drivers/mmc/host/dw_mmc.c | 125 +++++++++++++++++- drivers/mmc/host/dw_mmc.h | 2 + 3 files changed, 131 insertions(+), 2 deletions(-)
Signature · 1 line
2.38.3
PATCH 1/2 devicetree: synopsys-dw-mshc-common: add "fifo-access-32bit" property
--- .../devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml | 6 ++++++ 1 file changed, 6 insertions(+)
Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml +6 -0
@@ -57,6 +57,12 @@ properties: force fifo watermark setting accordingly. $ref: /schemas/types.yaml#/definitions/flag + fifo-access-32bit: + description: + Specifies that this device requires accesses to its 64-bit registers + to be done as pairs of 32-bit accesses, even on architectures where + readq is available. + dmas: maxItems: 1
Signature · 1 line
2.38.3
PATCH 2/2 dw_mmc: add an option to force 32-bit accesses to 64-bit device registers
In reply to Sergey Lisov--- drivers/mmc/host/dw_mmc.c | 125 +++++++++++++++++++++++++++++++++++++- drivers/mmc/host/dw_mmc.h | 2 + 2 files changed, 125 insertions(+), 2 deletions(-)
drivers/mmc/host/dw_mmc.c +123 -2
@@ -2575,6 +2575,119 @@ static void dw_mci_pull_data64(struct dw_mci *host, void *buf, int cnt) } } +/* +Some dw_mmc devices have 64-bit FIFOs, but expect them to be +accessed using two 32-bit accesses. If such controller is used +with a 64-bit kernel, this has to be done explicitly. + +XXX: Is this issue specific to Exynos7? +*/ + +static inline uint64_t mci_fifo_readq_32 (void __iomem *addr) +{ +uint64_t ans; +uint32_t proxy[2 ]; + + proxy[0 ] =mci_fifo_readl (addr); + proxy[1 ] =mci_fifo_readl (addr+4 ); +memcpy (&ans, proxy,8 ); +return ans; +} + +static inline void mci_fifo_writeq_32 (void __iomem *addr,uint64_t value) +{ +uint32_t proxy[2 ]; + +memcpy (proxy, &value,8 ); +mci_fifo_writel (addr, proxy[0 ]); +mci_fifo_writel (addr+4 , proxy[1 ]); +} + +static void dw_mci_push_data64_32 (struct dw_mci *host,void *buf,int cnt) +{ +struct mmc_data *data = host->data; +int init_cnt = cnt; + +/* try and push anything in the part_buf */ +if (unlikely (host->part_buf_count)) { +int len =dw_mci_push_part_bytes (host, buf, cnt); + + buf += len; + cnt -= len; + +if (host->part_buf_count ==8 ) { +mci_fifo_writeq_32 (host->fifo_reg, host->part_buf); + host->part_buf_count =0 ; + } + } +#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS +if (unlikely ((unsigned long )buf &0x7 )) { +while (cnt >=8 ) { +u64 aligned_buf[16 ]; +int len =min (cnt &-8 , (int )sizeof (aligned_buf)); +int items = len >>3 ; +int i; +/* memcpy from input buffer into aligned buffer */ +memcpy (aligned_buf, buf, len); + buf += len; + cnt -= len; +/* push data from aligned buffer into fifo */ +for (i =0 ; i < items; ++i) +mci_fifo_writeq_32 (host->fifo_reg, aligned_buf[i]); + } + } else +#endif + { +u64 *pdata = buf; + +for (; cnt >=8 ; cnt -=8 ) +mci_fifo_writeq_32 (host->fifo_reg, *pdata++); + buf = pdata; + } +/* put anything remaining in the part_buf */ +if (cnt) { +dw_mci_set_part_bytes (host, buf, cnt); +/* Push data if we have reached the expected data length */ +if ((data->bytes_xfered + init_cnt) == + (data->blksz * data->blocks)) +mci_fifo_writeq_32 (host->fifo_reg, host->part_buf); + } +} + +static void dw_mci_pull_data64_32 (struct dw_mci *host,void *buf,int cnt) +{ +#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS +if (unlikely ((unsigned long )buf &0x7 )) { +while (cnt >=8 ) { +/* pull data from fifo into aligned buffer */ +u64 aligned_buf[16 ]; +int len =min (cnt &-8 , (int )sizeof (aligned_buf)); +int items = len >>3 ; +int i; + +for (i =0 ; i < items; ++i) + aligned_buf[i] =mci_fifo_readq_32 (host->fifo_reg); + +/* memcpy from aligned buffer into output buffer */ +memcpy (buf, aligned_buf, len); + buf += len; + cnt -= len; + } + } else +#endif + { +u64 *pdata = buf; + +for (; cnt >=8 ; cnt -=8 ) + *pdata++ =mci_fifo_readq_32 (host->fifo_reg); + buf = pdata; + } +if (cnt) { + host->part_buf =mci_fifo_readq_32 (host->fifo_reg); +dw_mci_pull_final_bytes (host, buf, cnt); + } +} +static void dw_mci_pull_data (struct dw_mci *host,void *buf,int cnt) {int len;
@@ -3239,6 +3352,9 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)if (device_property_present (dev,"fifo-watermark-aligned" )) host->wm_aligned = true; +if (device_property_present (dev,"fifo-access-32bit" )) + host->quirks |=DW_MMC_QUIRK_FIFO64_32 ; +if (!device_property_read_u32 (dev,"clock-frequency" , &clock_frequency)) pdata->bus_hz = clock_frequency;
@@ -3367,8 +3483,13 @@ int dw_mci_probe(struct dw_mci *host) width =16 ; host->data_shift =1 ; }else if (i ==2 ) { - host->push_data = dw_mci_push_data64; - host->pull_data = dw_mci_pull_data64; +if ((host->quirks &DW_MMC_QUIRK_FIFO64_32 )) { + host->push_data = dw_mci_push_data64_32; + host->pull_data = dw_mci_pull_data64_32; + }else { + host->push_data = dw_mci_push_data64; + host->pull_data = dw_mci_pull_data64; + } width =64 ; host->data_shift =3 ; }else {
drivers/mmc/host/dw_mmc.h +2 -0
@@ -280,6 +280,8 @@ struct dw_mci_board {/* Support for longer data read timeout */ #define DW_MMC_QUIRK_EXTENDED_TMOUT BIT(0) +/* Force 32-bit access to the FIFO */ +#define DW_MMC_QUIRK_FIFO64_32 BIT(1)#define DW_MMC_240A 0x240a#define DW_MMC_280A 0x280a
Signature · 1 line
2.38.3
Re: [PATCH 1/2] devicetree: synopsys-dw-mshc-common: add "fifo-access-32bit" property
In reply to Sergey LisovOn 11/03/2023 16:22, Sergey Lisov wrote:
Use subject prefixes matching the subsystem (which you can get for example with git log --oneline -- DIRECTORY_OR_FILE on the directory your patch is touching).
Missing commit msg, which should answer why you are doing this and give more background.
Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml properties: · line 60
Quoted 13 lines
--- .../devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml | 6 ++++++ 1 file changed, 6 insertions(+)Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml +1
-0@@ -57,6 +57,12 @@ properties: force fifo watermark setting accordingly. $ref: /schemas/types.yaml#/definitions/flag + fifo-access-32bit:
Missing type boolean.
Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml properties: · line 64
Quoted 4 lines
Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml +4
-0+ description: + Specifies that this device requires accesses to its 64-bit registers + to be done as pairs of 32-bit accesses, even on architectures where + readq is available.
And why the device would require this? If it has 64-bit registers in the first place, they can be accessed in 64-bit. Otherwise these are not 64-bit registers, but just lower/upper 32-bit, right?
Also, why this cannot be implied from compatible? Why different boards with same SoC should have different FIFO access?
Best regards,
Krzysztof
Quoted 12 lines
Quoted 12 lines
--- .../devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml | 6 ++++++ 1 file changed, 6 insertions(+)Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml +0
-0@@ -57,6 +57,12 @@ properties: force fifo watermark setting accordingly. $ref: /schemas/types.yaml#/definitions/flag
Quoted 3 lines
Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml properties: · line 60
Quoted 1 line
Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml +1
-0+ fifo-access-32bit:Missing type boolean.
Thanks, will add the same $ref as for the entry above.
Quoted 11 lines
Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml properties: · line 64
Quoted 4 lines
Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml +4
-0+ description: + Specifies that this device requires accesses to its 64-bit registers + to be done as pairs of 32-bit accesses, even on architectures where + readq is available.And why the device would require this? If it has 64-bit registers in the first place, they can be accessed in 64-bit. Otherwise these are not 64-bit registers, but just lower/upper 32-bit, right?
Also, why this cannot be implied from compatible? Why different boards with same SoC should have different FIFO access?
It probably can be implied, but I am not exactly sure on which boards it affects, so I decided to go for a new devicetree option. Anyway, the same argument applies to the "data-addr" property, which is already in the spec, so I supposed that adding such knobs is fine.
Re: broken subject?
Quoted 4 lines · Sergey Lisov
Quoted 4 lines
Quoted 4 lines
--- .../devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml | 6 ++++++ 1 file changed, 6 insertions(+)
Why did you remove the subject? Please keep the mailing process matching mailing lists. It messes with mailboxes, filters and reading process.
Quoted 23 lines
Quoted 11 lines
Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml properties: · line 60
Quoted 9 lines
Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml +1
-0@@ -57,6 +57,12 @@ properties: force fifo watermark setting accordingly. $ref: /schemas/types.yaml#/definitions/flag + fifo-access-32bit:Missing type boolean.
Thanks, will add the same $ref as for the entry above.
Quoted 9 lines
Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml properties: · line 64
Quoted 4 lines
Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml +4
-0+ description: + Specifies that this device requires accesses to its 64-bit registers + to be done as pairs of 32-bit accesses, even on architectures where + readq is available.And why the device would require this? If it has 64-bit registers in the first place, they can be accessed in 64-bit. Otherwise these are not 64-bit registers, but just lower/upper 32-bit, right?
Quoted 7 lines
Quoted 2 lines
Also, why this cannot be implied from compatible? Why different boards with same SoC should have different FIFO access?
It probably can be implied, but I am not exactly sure on which boards it affects, so I decided to go for a new devicetree option. Anyway, the same argument applies to the "data-addr" property, which is already in the spec, so I supposed that adding such knobs is fine.
Yeah, Rob acked it so I will let him to judge this. To me it looks like unnecessary fragmentation - this looks like compatible specific, not board. Anyway you need to resend to fix all the mailing mess.
Best regards,
Krzysztof
Re: [PATCH 1/2] devicetree: synopsys-dw-mshc-common: add "fifo-access-32bit" property
Quoted 2 lines
Why did you remove the subject? Please keep the mailing process matching mailing lists. It messes with mailboxes, filters and reading process.
Sorry about this, I just wanted to get rid of those X-Something headers and accidentially deleted this one.
Quoted 6 lines
Yeah, Rob acked it so I will let him to judge this. To me it looks like unnecessary fragmentation - this looks like compatible specific, not board. Anyway you need to resend to fix all the mailing mess.
Best regards,
Krzysztof
Should I resend the whole patchset from scratch, as if nothing happened?
Re: [PATCH 1/2] devicetree: synopsys-dw-mshc-common: add "fifo-access-32bit" property
In reply to Krzysztof KozlowskiQuoted 2 lines
Why did you remove the subject? Please keep the mailing process matching mailing lists. It messes with mailboxes, filters and reading process.
Sorry about this, I just wanted to get rid of those X-Something headers and accidentially deleted this one.
Quoted 6 lines
Yeah, Rob acked it so I will let him to judge this. To me it looks like unnecessary fragmentation - this looks like compatible specific, not board. Anyway you need to resend to fix all the mailing mess.
Best regards,
Krzysztof
Should I resend the whole patchset from scratch, as if nothing happened?
Re: [PATCH 1/2] devicetree: synopsys-dw-mshc-common: add "fifo-access-32bit" property
In reply to Krzysztof KozlowskiQuoted 2 lines
Why did you remove the subject? Please keep the mailing process matching mailing lists. It messes with mailboxes, filters and reading process.
Sorry about this, I just wanted to get rid of those X-Something headers and accidentially deleted this one.
Quoted 6 lines
Yeah, Rob acked it so I will let him to judge this. To me it looks like unnecessary fragmentation - this looks like compatible specific, not board. Anyway you need to resend to fix all the mailing mess.
Best regards,
Krzysztof
Should I resend the whole patchset from scratch, as if nothing happened?