Skip to contentSkip to conversation

riscv: setup per-hart stack earlier

PATCH Superseded Bo Gan 2 participants 3 messages May 9, 2023 – May 21, 2023 1 message not in the archive RISC-V

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore

Bo Gan

author
#0 lore raw

PATCH 1/1 riscv: setup per-hart stack earlier

Harts need to use per-hart stack before any function call, even if that function is a simple one. When the callee uses stack for register save/ restore, especially RA, if nested call, concurrent access by multiple harts on the same stack will cause data-race.

This patch sets up SP before board_init_f_alloc_reserve. A side effect of this is that the memory layout has changed as the following:

+----------------+        +----------------+ <----- SPL_STACK/
|  ......        |        |  hart 0 stack  |        SYS_INIT_SP_ADDR
|  malloc_base   |        +----------------+
+----------------+        |  hart 1 stack  |
|  GD            |        +----------------+ If not SMP, N=1
+----------------+        |  ......        |
|  hart 0 stack  |        +----------------+
+----------------+   ==>  |  hart N-1 stack|
|  hart 1 stack  |        +----------------+
+----------------+        |  ......        |
|  ......        |        |  malloc_base   |
+----------------+        +----------------+
|  hart N-1 stack|        |  GD            |
+----------------+        +----------------+
|                |        |                |
---
 arch/riscv/cpu/start.S | 37 ++++++++++++++++++++++++-------------
 1 file changed, 24 insertions(+), 13 deletions(-)
arch/riscv/cpu/start.S +24 -13
index dad22bf..90015c2 100644
@@ -91,16 +91,35 @@ _start:
  * Set stackpointer in internal/ex RAM to call board_init_f
  */
 call_board_init_f:
-	li	t0, -16
 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_STACK)
-	li	t1, CONFIG_SPL_STACK
+	li	t0, CONFIG_SPL_STACK
 #else
-	li	t1, SYS_INIT_SP_ADDR
+	li	t0, CONFIG_SYS_INIT_SP_ADDR
 #endif
-	and	sp, t1, t0		/* force 16 byte alignment */
+	and	t0, t0, -16		/* force 16 byte alignment */
+
+	/* setup stack */
+#if CONFIG_IS_ENABLED(SMP)
+	/* tp: hart id */
+	slli	t1, tp, CONFIG_STACK_SIZE_SHIFT
+	sub	sp, t0, t1
+#else
+	mv	sp, t0
+#endif
+/*
+ * Now sp points to the right stack belonging to current CPU.
+ * It's essential before any function call, otherwise, we get data-race.
+ */
 
 call_board_init_f_0:
-	mv	a0, sp
+	/* find top of reserve space */
+#if CONFIG_IS_ENABLED(SMP)
+	li	t1, CONFIG_NR_CPUS
+#else
+	li	t1, 1
+#endif
+	slli	t1, t1, CONFIG_STACK_SIZE_SHIFT
+	sub	a0, t0, t1		/* t1 -> size of all CPU stacks */
 	jal	board_init_f_alloc_reserve
 
 	/*
@@ -109,14 +128,6 @@ call_board_init_f_0:
 	 */
 	mv	s0, a0
 
-	/* setup stack */
-#if CONFIG_IS_ENABLED(SMP)
-	/* tp: hart id */
-	slli	t0, tp, CONFIG_STACK_SIZE_SHIFT
-	sub	sp, a0, t0
-#else
-	mv	sp, a0
-#endif
 
 	/* Configure proprietary settings and customized CSRs of harts */
 call_harts_early_init:
Signature · 1 line
2.7.4

A message that is not in the archive (sent off-list or not yet received): PU1PR03MB2997C9798333E19248549F50C1749@PU1PR03MB2997.apcprd03.prod.outlook.com

#2 lore raw

Hi Bo Gan,

Quoted 37 lines

From: Bo Gan <[email protected]>
Sent: Tuesday, May 09, 2023 9:46 AM
To: [email protected]
Cc: Bo Gan <[email protected]>; Rick Jian-Zhi Chen(陳建志) <[email protected]>; Leo Yu-Chi Liang(梁育齊) <[email protected]>
Subject: [PATCH] riscv: setup per-hart stack earlier

Harts need to use per-hart stack before any function call, even if that function is a simple one. When the callee uses stack for register save/ restore, especially RA, if nested call, concurrent access by multiple harts on the same stack will cause data-race.

This patch sets up SP before board_init_f_alloc_reserve. A side effect of this is that the memory layout has changed as the following:

+----------------+        +----------------+ <----- SPL_STACK/
|  ......        |        |  hart 0 stack  |        SYS_INIT_SP_ADDR
|  malloc_base   |        +----------------+
+----------------+        |  hart 1 stack  |
|  GD            |        +----------------+ If not SMP, N=1
+----------------+        |  ......        |
|  hart 0 stack  |        +----------------+
+----------------+   ==>  |  hart N-1 stack|
|  hart 1 stack  |        +----------------+
+----------------+        |  ......        |
|  ......        |        |  malloc_base   |
+----------------+        +----------------+
|  hart N-1 stack|        |  GD            |
+----------------+        +----------------+
|                |        |                |
---
 arch/riscv/cpu/start.S | 37 ++++++++++++++++++++++++-------------
 1 file changed, 24 insertions(+), 13 deletions(-)

arch/riscv/cpu/start.S _start: · line 97

Quoted 10 lines
arch/riscv/cpu/start.S +2 -3
@@ -91,16 +91,35 @@ _start:
  * Set stackpointer in internal/ex RAM to call board_init_f
  */
 call_board_init_f:
-       li      t0, -16
 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_STACK)
-       li      t1, CONFIG_SPL_STACK
+       li      t0, CONFIG_SPL_STACK
 #else
-       li      t1, SYS_INIT_SP_ADDR
+       li      t0, CONFIG_SYS_INIT_SP_ADDR

It builds fail as below:

arch/riscv/cpu/start.S:97: Error: illegal operands `li t0,CONFIG_SYS_INIT_SP_ADDR'

Thanks,
Rick