Skip to contentSkip to conversation

ASoC: codecs: rtq9128: Add TDM input source select

PATCH In review [email protected] 2 participants 4 messages Sep 28, 2023

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

cover ASoC: codecs: rtq9128: Add TDM input source select

From: ChiYuan Huang <[email protected]>

This patch series create a TDM source select property and use it to decide which TDM data source is connected.

Following by the below patch disccuion
https://lore.kernel.org/lkml/[email protected]/#t
It may not be a good choice to add the user controlable mixer control item. Since it follows the board design, make it as a device property.

ChiYuan Huang (2):
ASoC: dt-bindings: rtq9128: Add TDM input source slect property
ASoC: codecs: rtq9128: Add TDM input source select

 .../bindings/sound/richtek,rtq9128.yaml          |  7 +++++++
 sound/soc/codecs/rtq9128.c                       | 16 +++++++++++++++-
 2 files changed, 22 insertions(+), 1 deletion(-)

base-commit: 3efcb471f871cc095841d411f98c593228ecbac6

Signature · 1 line
2.34.1
#1 lore raw

PATCH 1/2 ASoC: dt-bindings: rtq9128: Add TDM input source slect property

From: ChiYuan Huang <[email protected]>

Create a boolean property to select TDM input source coms from 'DATA2'.

---
 .../devicetree/bindings/sound/richtek,rtq9128.yaml         | 7 +++++++
 1 file changed, 7 insertions(+)
Documentation/devicetree/bindings/sound/richtek,rtq9128.yaml +7 -0
index d117f08fff30..d54686a19ab7 100644
@@ -28,6 +28,13 @@ properties:
   enable-gpios:
     maxItems: 1
 
+  richtek,tdm-input-data2-select:
+    type: boolean
+    description:
+      By default, if TDM mode is used, TDM data input will select 'DATA1' pin
+      as the data source. This option will configure TDM data input source from
+      'DATA1' to 'DATA2' pin.
+
   '#sound-dai-cells':
     const: 0
 
Signature · 1 line
2.34.1
#2 lore raw

PATCH 2/2 ASoC: codecs: rtq9128: Add TDM input source select

In reply to [email protected]

From: ChiYuan Huang <[email protected]>

Pase the property to decide the TDM input source comes from 'DATA1' or 'DATA2 pin.

---
 sound/soc/codecs/rtq9128.c | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)
sound/soc/codecs/rtq9128.c +15 -1
index 926b79ed8078..371d622c6214 100644
@@ -14,6 +14,7 @@
 #include <linux/mod_devicetable.h>
 #include <linux/module.h>
 #include <linux/pm_runtime.h>
+#include <linux/property.h>
 #include <linux/regmap.h>
 #include <sound/pcm_params.h>
 #include <sound/soc.h>
@@ -41,6 +42,7 @@
 
 #define RTQ9128_CHSTAT_VAL_MASK	GENMASK(1, 0)
 #define RTQ9128_DOLEN_MASK	GENMASK(7, 6)
+#define RTQ9128_TDMSRCIN_MASK	GENMASK(5, 4)
 #define RTQ9128_AUDBIT_MASK	GENMASK(5, 4)
 #define RTQ9128_AUDFMT_MASK	GENMASK(3, 0)
 #define RTQ9128_MSMUTE_MASK	BIT(0)
@@ -59,6 +61,7 @@ struct rtq9128_data {
 	struct gpio_desc *enable;
 	int tdm_slots;
 	int tdm_slot_width;
+	bool tdm_input_data2_select;
 };
 
 struct rtq9128_init_reg {
@@ -484,7 +487,7 @@ static int rtq9128_dai_set_tdm_slot(struct snd_soc_dai *dai, unsigned int tx_mas
 	struct rtq9128_data *data = snd_soc_dai_get_drvdata(dai);
 	struct snd_soc_component *comp = dai->component;
 	struct device *dev = dai->dev;
-	unsigned int mask, start_loc;
+	unsigned int mask, start_loc, srcin_select;
 	int i, frame_length, ret;
 
 	dev_dbg(dev, "%s: slot %d slot_width %d, tx/rx mask 0x%x 0x%x\n", __func__, slots,
@@ -530,6 +533,14 @@ static int rtq9128_dai_set_tdm_slot(struct snd_soc_dai *dai, unsigned int tx_mas
 		}
 	}
 
+	srcin_select = data->tdm_input_data2_select ? RTQ9128_TDMSRCIN_MASK : 0;
+	ret = snd_soc_component_update_bits(comp, RTQ9128_REG_SDO_SEL, RTQ9128_TDMSRCIN_MASK,
+					    srcin_select);
+	if (ret < 0) {
+		dev_err(dev, "Failed to configure TDM source input select\n");
+		return ret;
+	}
+
 	data->tdm_slots = slots;
 	data->tdm_slot_width = slot_width;
 
@@ -672,6 +683,9 @@ static int rtq9128_probe(struct i2c_client *i2c)
 	else if (data->enable)
 		usleep_range(10000, 11000);
 
+	data->tdm_input_data2_select = device_property_read_bool(dev,
+								 "richtek,tdm-input-data2-select");
+
 	i2c_set_clientdata(i2c, data);
 
 	/*
Signature · 1 line
2.34.1
maintainer
#3 lore raw
In reply to [email protected]
Quoted 9 lines · On Thu, 28 Sep 2023 11:41:06 +0800, [email protected] wrote:

This patch series create a TDM source select property and use it to decide which TDM data source is connected.

Following by the below patch disccuion
https://lore.kernel.org/lkml/[email protected]/#t
It may not be a good choice to add the user controlable mixer control item. Since it follows the board design, make it as a device property.

[...]

Applied to

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next

Thanks!

[1/2] ASoC: dt-bindings: rtq9128: Add TDM input source slect property

      commit: bf38a0be7c57e43303600b5afc9b740882b3ed87
[2/2] ASoC: codecs: rtq9128: Add TDM input source select
      commit: 54ac512048c98b720a8fbf5899308788dff8def0

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark