Skip to contentSkip to conversation

PROBLEM: My USB controller dosn't work correctly

DISCUSSION Philipp Benner 1 participant 1 message Jan 27, 2002

lore
Share & tools
lore

Philipp Benner

author
#0 lore raw

Hi,

[1.] My USB controller dosn't work correctly
[2.] I've the Logitech MiniWheel Mouse USB. After booting linux it works correctly, but some hours or days later
i can't move the curser any longer. There is an error message like this
at tty1:

usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110)

If i reconnect the mouse the same error message comes again. After
rebooting it works...
[3.] <*> Support for USB
[*] USB verbose debug messages
--- Miscellaneous USB options
[*] Preliminary USB device filesystem
[ ] Enforce USB bandwidth allocation (EXPERIMENTAL)
[ ] Long timeout for slow-responding devices (some MGE Ellipse
UPSes) (Same problem with this option enabled)
--- USB Controllers
<*> UHCI Alternate Driver (JE) support
< > OHCI (Compaq, iMacs, OPTi, SiS, ALi, ...) support
--- USB Device Class drivers
< > USB Audio support
< > USB Bluetooth support (EXPERIMENTAL)
< > USB Mass Storage support
< > USB Modem (CDC ACM) support
< > USB Printer support
--- USB Human Interface Devices (HID)
< > USB Human Interface Device (full HID) support (Same problem
with this option enabled)

       < >   USB HIDBP Keyboard (basic) support
       <*>   USB HIDBP Mouse (basic) support
       <*>   Wacom Intuos/Graphire tablet support       (Same problem

without this option enabled)
--- USB Imaging devices
< > USB Kodak DC-2xx Camera support
< > USB Mustek MDC800 Digital Camera support (EXPERIMENTAL)
< > USB Scanner support
< > Microtek X6USB scanner support
< > HP53xx USB scanner support (EXPERIMENTAL)

--- USB Multimedia devices

< > USB IBM (Xirlink) C-it Camera support

< > USB OV511 Camera support

< > USB Philips Cameras
< > USB SE401 Camera support
< > D-Link USB FM radio support (EXPERIMENTAL)
< > DABUSB driver
--- USB Network adaptors

< > USB ADMtek Pegasus-based ethernet device support (EXPERIMENTAL)
< > USB KLSI KL5USB101-based
ethernet device support (EXPERIMENTAL) < >
USB CATC NetMate-based Ethernet device support (EXPERIMENTAL)
< > USB Communication Class Ethernet device support (EXPERIMENTAL)

< > USB-to-USB Networking cable device support (EXPERIMENTAL)
--- USB port drivers
< > USS720 parport driver

[4.] cat /proc/version

     Linux version 2.4.17 (root@warlock) (gcc version 2.95.4 20011006

(Debian prerelease)) #4 Son Dez 23 14:16:58 CET 2001

[5.] cat /proc/cpuinfo

     processor       : 0
     vendor_id       : GenuineIntel
     cpu family      : 6
     model           : 7
     model name      : Pentium III (Katmai)
     stepping        : 2
     cpu MHz         : 501.178
     cache size      : 512 KB
     fdiv_bug        : no
     hlt_bug         : no
     f00f_bug        : no
     coma_bug        : no
     fpu             : yes
     fpu_exception   : yes
     cpuid level     : 2
     wp              : yes
     flags           : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca
cmov pat pse36 mmx fxsr sse
     bogomips        : 999.42

[6.] lspci -vvv
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev 06)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+

        Latency: 16
        Region 0: Memory at e8000000 (32-bit, prefetchable) [size=64M]
        Capabilities: [a0] AGP version 1.0
                Status: RQ=7 SBA+ 64bit- FW- Rate=x1,x2
                Command: RQ=0 SBA- AGP+ 64bit- FW- Rate=x2

00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: ec000000-edffffff
Prefetchable memory behind bridge: e0000000-e7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C596 ISA [Mobile South] (rev
07)
Subsystem: VIA Technologies, Inc. VT82C596/A/B PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 64
        Region 4: I/O ports at d000 [size=16]

00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 02) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at d400 [size=32]

00:07.3 Host bridge: VIA Technologies, Inc. VT82C596 Power Management
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

00:0e.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 04)
Subsystem: Creative Labs CT4850 SBLive! Value
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at d800 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0e.1 Input device controller: Creative Labs SB Live! (rev 01)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 0: I/O ports at dc00 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.0 Multimedia video controller: Brooktree Corporation Bt848 TV with DMA push (rev 12)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 64 (4000ns min, 10000ns max)
        Interrupt: pin A routed to IRQ 12
        Region 0: Memory at ee000000 (32-bit, prefetchable) [size=4K]

00:12.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at e000 [size=32]

00:14.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev
10)
Subsystem: Allied Telesyn International: Unknown device 2503
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at e400 [size=256]
Region 1: Memory at ee001000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: nVidia Corporation NV11 (GeForce2 MX) (rev a1) (prog-if 00 [VGA])
Subsystem: Elsa AG: Unknown device 0c60
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 248 (1250ns min, 250ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at ec000000 (32-bit, non-prefetchable) [size=16M]
        Region 1: Memory at e0000000 (32-bit, prefetchable) [size=128M]
        Expansion ROM at ed000000 [disabled] [size=64K]
        Capabilities: [60] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA

PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW+ Rate=x1,x2
Command: RQ=7 SBA- AGP+ 64bit- FW- Rate=x2

[7.] cat /proc/driver/uhci/hc0
HC status
usbcmd = 00c1 Maxp64 CF RS
usbstat = 0000
usbint = 000f
usbfrnum = (0)21c
flbaseadd = 17ef0000
sof = 40
stat1 = 05a5 LowSpeed PortEnabled PortConnected
stat2 = 0580 LowSpeed
Frame List
Skeleton TD's
- skel_term_td
[d7ef51b0] link (17ef51b0) e0 IOC Length=0 MaxLen=7ff DT0 EndPt=0
Dev=7f, PID=69(IN) (buf=00000000)
Skeleton QH's

[8.] cat /proc/bus/usb/devices

     T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
     B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
     D:  Ver= 1.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
     P:  Vendor=0000 ProdID=0000 Rev= 0.00
     S:  Product=USB UHCI-alt Root Hub
     S:  SerialNumber=d400
     C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
     I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
     E:  Ad=81(I) Atr=03(Int.) MxPS=   8 Ivl=255ms

[9.] cat /proc/bus/usb/drivers
usbdevfs
hub
usb_mouse
wacom

Thanks for your help!

Signature · 2 lines
GMX - Die Kommunikationsplattform im Internet.
http://www.gmx.net