Skip to contentSkip to conversation

PCI Issues with ExpressCard/54 Audio Device

DISCUSSION Alnie 3 participants 14 messages Feb 26, 2015 – Mar 3, 2015 1 message not in the archive PCI

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

Alnie

author
#1 lore raw

Hi, I am seeking feedback in regards to issues with a ExpressCard/54 audio card (http://www.notebookreview.com/notebookreview/creative-soundblaster-x-fi-xtreme-audio-for-notebook-review/) under Linux (same card has been working fine in Win 7). After recently having a conversation on alsa-devel about it, it was decided it seems to be a PCI issue. The "devices" in question....

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Flags: bus master, fast devsel, latency 0
Bus: primary=05, secondary=06, subordinate=0c, sec-latency=36
Memory behind bridge: f4300000-f43fffff
Capabilities: [50] Power Management version 3
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express PCI-Express to PCI/PCI-X Bridge, MSI 00
Capabilities: [100] Advanced Error Reporting

06:00.0 Audio device: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG
Subsystem: Creative Labs SB1040
Flags: bus master, fast Back2Back, medium devsel, latency 32, IRQ 19 Memory at f4300000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [dc] Power Management version 3
Kernel driver in use: snd_hda_intel

dmesg output... http://pastebin.com/66UE659K

and comments in regard to it... http://mailman.alsa-project.org/pipermail/alsa-devel/2015-February/088237.html

Quoted 10 lines
[ 2619.199658] pciehp 0000:00:1c.3:pcie04: Card not present on Slot(3)
[ 2619.199666] pciehp 0000:00:1c.3:pcie04: slot(3): Link Down event
[ 2619.199674] pciehp 0000:00:1c.3:pcie04: Link Down event ignored on 
slot(3): already powering off
[ 2619.199911] pci_bus 0000:06: busn_res: [bus 06-0c] is released
[ 2620.757928] pciehp 0000:00:1c.3:pcie04: Card present on Slot(3)
[ 2620.767950] pciehp 0000:00:1c.3:pcie04: slot(3): Link Up event
[ 2620.767985] pciehp 0000:00:1c.3:pcie04: Link Up event ignored on 

slot(3): already powering on

pciehp reacted power off and on here, and...

Quoted 6 lines
[ 2620.876160] pci 0000:05:00.0: [1102:7006] type 01 class 0x060400
[ 2620.876426] pci 0000:05:00.0: supports D1 D2
[ 2620.876719] pci 0000:05:00.0: bridge configuration invalid ([bus 
00-00]), reconfiguring
[ 2620.876928] pci_bus 0000:06: busn_res: can not insert [bus 06-ff] 

under [bus 05-0c] (conflicts with (null) [bus 05-0c])

.... and something failed here for the PCI bridge device.

Quoted 25 lines
[ 2620.876967] pci 0000:06:00.0: [1102:0009] type 00 class 0x040300
[ 2620.877013] pci 0000:06:00.0: reg 0x10: [mem 0x00000000-0x00003fff]
[ 2620.877203] pci 0000:06:00.0: supports D1 D2
[ 2620.877443] pci 0000:05:00.0: PCI bridge to [bus 06-ff]
[ 2620.877462] pci 0000:05:00.0:   bridge window [io  0x0000-0x0fff]
[ 2620.877474] pci 0000:05:00.0:   bridge window [mem 0x00000000-0x000fffff]
[ 2620.877492] pci 0000:05:00.0:   bridge window [mem 
0x00000000-0x000fffff 64bit pref]
[ 2620.877500] pci_bus 0000:06: busn_res: [bus 06-ff] end is updated to 06
[ 2620.877559] pci 0000:05:00.0: BAR 14: assigned [mem 
0xf4300000-0xf43fffff]
[ 2620.877568] pci 0000:05:00.0: BAR 15: assigned [mem 
0xf4000000-0xf40fffff 64bit pref]
[ 2620.877574] pci 0000:05:00.0: BAR 13: assigned [io  0x2000-0x2fff]
[ 2620.877582] pci 0000:06:00.0: BAR 0: assigned [mem 0xf4300000-0xf4303fff]
[ 2620.877595] pci 0000:05:00.0: PCI bridge to [bus 06]
[ 2620.877603] pci 0000:05:00.0:   bridge window [io  0x2000-0x2fff]
[ 2620.877618] pci 0000:05:00.0:   bridge window [mem 0xf4300000-0xf43fffff]
[ 2620.877630] pci 0000:05:00.0:   bridge window [mem 
0xf4000000-0xf40fffff 64bit pref]
[ 2620.877647] pcieport 0000:00:1c.3: PCI bridge to [bus 05-0c]
[ 2620.877655] pcieport 0000:00:1c.3:   bridge window [io  0x2000-0x2fff]
[ 2620.877667] pcieport 0000:00:1c.3:   bridge window [mem 
0xf4300000-0xf7efffff]
[ 2620.877677] pcieport 0000:00:1c.3:   bridge window [mem 
Quoted 8 lines

0xf4000000-0xf40fffff 64bit pref]

[ 2620.877990] pci 0000:05:00.0: enabling device (0000 -> 0003)
[ 2620.878013] snd_hda_intel 0000:06:00.0: enabling device (0000 -> 0002)
[ 2620.882747] azx_single_wait_for_response: 108 callbacks suppressed
[ 2620.882753] snd_hda_intel 0000:06:00.0: Codec #1 probe error; 
disabling it...
[ 2620.887052] snd_hda_intel 0000:06:00.0: no AFG or MFG node found
[ 2620.887058] snd_hda_intel 0000:06:00.0: no codecs initialized

I've tried many kernels from 2.6 to 3.18 with similar results. Willing to retrieve more info. Thank you :)

-Alnie

maintainer
#2 lore raw

[+cc Takashi]

Quoted 1 line · Alnie

Hi, I am seeking feedback in regards to issues with a ExpressCard/54 audio card (http://www.notebookreview.com/notebookreview/creative-soundblaster-x-fi-xtreme-audio-for-notebook-review/) under Linux (same card has been working fine in Win 7). After recently having a conversation on alsa-devel about it, it was decided it seems to be a PCI issue. The "devices" in question....

Hi Alnie,

I'm sorry you're running into a problem, but thanks for the report!

Quoted 81 lines

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Flags: bus master, fast devsel, latency 0
Bus: primary=05, secondary=06, subordinate=0c, sec-latency=36
Memory behind bridge: f4300000-f43fffff
Capabilities: [50] Power Management version 3
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express PCI-Express to PCI/PCI-X Bridge, MSI 00
Capabilities: [100] Advanced Error Reporting

06:00.0 Audio device: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG
Subsystem: Creative Labs SB1040
Flags: bus master, fast Back2Back, medium devsel, latency 32, IRQ 19 Memory at f4300000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [dc] Power Management version 3
Kernel driver in use: snd_hda_intel

dmesg output... http://pastebin.com/66UE659K

and comments in regard to it... http://mailman.alsa-project.org/pipermail/alsa-devel/2015-February/088237.html

Quoted 10 lines
[ 2619.199658] pciehp 0000:00:1c.3:pcie04: Card not present on Slot(3)
[ 2619.199666] pciehp 0000:00:1c.3:pcie04: slot(3): Link Down event
[ 2619.199674] pciehp 0000:00:1c.3:pcie04: Link Down event ignored on
slot(3): already powering off
[ 2619.199911] pci_bus 0000:06: busn_res: [bus 06-0c] is released
[ 2620.757928] pciehp 0000:00:1c.3:pcie04: Card present on Slot(3)
[ 2620.767950] pciehp 0000:00:1c.3:pcie04: slot(3): Link Up event
[ 2620.767985] pciehp 0000:00:1c.3:pcie04: Link Up event ignored on

slot(3): already powering on

pciehp reacted power off and on here, and...

Quoted 6 lines
[ 2620.876160] pci 0000:05:00.0: [1102:7006] type 01 class 0x060400
[ 2620.876426] pci 0000:05:00.0: supports D1 D2
[ 2620.876719] pci 0000:05:00.0: bridge configuration invalid ([bus
00-00]), reconfiguring
[ 2620.876928] pci_bus 0000:06: busn_res: can not insert [bus 06-ff]

under [bus 05-0c] (conflicts with (null) [bus 05-0c])

.... and something failed here for the PCI bridge device.

Quoted 25 lines
[ 2620.876967] pci 0000:06:00.0: [1102:0009] type 00 class 0x040300
[ 2620.877013] pci 0000:06:00.0: reg 0x10: [mem 0x00000000-0x00003fff]
[ 2620.877203] pci 0000:06:00.0: supports D1 D2
[ 2620.877443] pci 0000:05:00.0: PCI bridge to [bus 06-ff]
[ 2620.877462] pci 0000:05:00.0:   bridge window [io  0x0000-0x0fff]
[ 2620.877474] pci 0000:05:00.0:   bridge window [mem 0x00000000-0x000fffff]
[ 2620.877492] pci 0000:05:00.0:   bridge window [mem
0x00000000-0x000fffff 64bit pref]
[ 2620.877500] pci_bus 0000:06: busn_res: [bus 06-ff] end is updated to 06
[ 2620.877559] pci 0000:05:00.0: BAR 14: assigned [mem
0xf4300000-0xf43fffff]
[ 2620.877568] pci 0000:05:00.0: BAR 15: assigned [mem
0xf4000000-0xf40fffff 64bit pref]
[ 2620.877574] pci 0000:05:00.0: BAR 13: assigned [io  0x2000-0x2fff]
[ 2620.877582] pci 0000:06:00.0: BAR 0: assigned [mem 0xf4300000-0xf4303fff]
[ 2620.877595] pci 0000:05:00.0: PCI bridge to [bus 06]
[ 2620.877603] pci 0000:05:00.0:   bridge window [io  0x2000-0x2fff]
[ 2620.877618] pci 0000:05:00.0:   bridge window [mem 0xf4300000-0xf43fffff]
[ 2620.877630] pci 0000:05:00.0:   bridge window [mem
0xf4000000-0xf40fffff 64bit pref]
[ 2620.877647] pcieport 0000:00:1c.3: PCI bridge to [bus 05-0c]
[ 2620.877655] pcieport 0000:00:1c.3:   bridge window [io  0x2000-0x2fff]
[ 2620.877667] pcieport 0000:00:1c.3:   bridge window [mem
0xf4300000-0xf7efffff]
[ 2620.877677] pcieport 0000:00:1c.3:   bridge window [mem
Quoted 8 lines

0xf4000000-0xf40fffff 64bit pref]

[ 2620.877990] pci 0000:05:00.0: enabling device (0000 -> 0003)
[ 2620.878013] snd_hda_intel 0000:06:00.0: enabling device (0000 -> 0002)
[ 2620.882747] azx_single_wait_for_response: 108 callbacks suppressed
[ 2620.882753] snd_hda_intel 0000:06:00.0: Codec #1 probe error;
disabling it...
[ 2620.887052] snd_hda_intel 0000:06:00.0: no AFG or MFG node found
[ 2620.887058] snd_hda_intel 0000:06:00.0: no codecs initialized
Quoted 1 line

I've tried many kernels from 2.6 to 3.18 with similar results. Willing to retrieve more info. Thank you :)

It looks like you booted with the card already installed, then removed and reinstalled it. Did the card work at any point? If it worked before the hotplug, then we need to look for a hotplug problem. If it never worked, then we can ignore hotplug for now.

My guess is that the card never worked at all and hotplug isn't an issue here.

The pciehp messages above are a bit scary looking, but I don't think they actually show a problem. It looks like you booted with the ExpressCard present, and it was configured like this:

pci 0000:00:1c.3: PCI bridge to [bus 05-0c]

  pci 0000:00:1c.3:   bridge window [io  0x2000-0x2fff]
  pci 0000:00:1c.3:   bridge window [mem 0xf4300000-0xf7efffff]
  pci 0000:00:1c.3:   bridge window [mem 0xf4000000-0xf40fffff 64bit pref]

pci 0000:05:00.0: PCI bridge to [bus 06-0c]
pci 0000:05:00.0: bridge window [mem 0xf4300000-0xf43fffff]
pci 0000:06:00.0: [1102:0009] type 00 class 0x040300 pci 0000:06:00.0: reg 0x10: [mem 0xf4300000-0xf4303fff] pciehp 0000:00:1c.3:pcie04: Slot #3 AttnBtn- AttnInd- PwrInd-
PwrCtrl- MRL- Interlock- NoCompl- LLActRep+

The kernel didn't change anything on the device, but the driver complained:

snd_hda_intel 0000:06:00.0: Codec #1 probe error; disabling it... snd_hda_intel 0000:06:00.0: no AFG or MFG node found snd_hda_intel 0000:06:00.0: no codecs initialized

I assume the device is not working at this point. (Correct me if I'm wrong.) Some time later, at timestamp 2620, it looks like you unplugged and replugged the ExpressCard. We reconfigured the bridge and device like this:

pci 0000:05:00.0: PCI bridge to [bus 06]

  pci 0000:05:00.0:   bridge window [io  0x2000-0x2fff]
  pci 0000:05:00.0:   bridge window [mem 0xf4300000-0xf43fffff]
  pci 0000:05:00.0:   bridge window [mem 0xf4000000-0xf40fffff 64bit pref]

pci 0000:06:00.0: BAR 0: assigned [mem 0xf4300000-0xf4303fff]

This is slightly different than what we had initially:

- 05:00.0 bridge bus aperture is [bus 06] instead of [bus 06-0c]
- 05:00.0 bridge io aperture is enabled instead of disabled
- 05:00.0 bridge mem pref aperture is enabled instead of disabled

But none of these is a problem and the audio device itself at 06:00.0 is programmed identically to what we had initially. And it looks like the driver complains exactly the same way it did at boot-time. So I don't think this is related to hotplug.

Can you use a program like this:
http://cmp.felk.cvut.cz/~pisa/linux/rdwrmem.c to read some of the device registers, e.g., the ones mapped by BAR 0 at 0xf4300000? I don't know what the register layout is, but if you get all 0xff responses, that might indicate that the device isn't responding, either because we haven't enabled it correctly or we haven't routed that space correctly, or .... If you get any data that is NOT all ones, that means the device is responding.

Could you also collect the output of "lspci -vvs00:1c.3", "lspci -vvs05:000" and "lspci -vvs06:00.0"?

Bjorn

#3 lore raw

At Wed, 25 Feb 2015 22:55:15 -0800,

Quoted 152 lines · Bjorn Helgaas

[+cc Takashi]

Quoted 1 line · Alnie

Hi, I am seeking feedback in regards to issues with a ExpressCard/54 audio card (http://www.notebookreview.com/notebookreview/creative-soundblaster-x-fi-xtreme-audio-for-notebook-review/) under Linux (same card has been working fine in Win 7). After recently having a conversation on alsa-devel about it, it was decided it seems to be a PCI issue. The "devices" in question....

Hi Alnie,

I'm sorry you're running into a problem, but thanks for the report!

Quoted 81 lines

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Flags: bus master, fast devsel, latency 0
Bus: primary=05, secondary=06, subordinate=0c, sec-latency=36
Memory behind bridge: f4300000-f43fffff
Capabilities: [50] Power Management version 3
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express PCI-Express to PCI/PCI-X Bridge, MSI 00
Capabilities: [100] Advanced Error Reporting

06:00.0 Audio device: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG
Subsystem: Creative Labs SB1040
Flags: bus master, fast Back2Back, medium devsel, latency 32, IRQ 19 Memory at f4300000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [dc] Power Management version 3
Kernel driver in use: snd_hda_intel

dmesg output... http://pastebin.com/66UE659K

and comments in regard to it... http://mailman.alsa-project.org/pipermail/alsa-devel/2015-February/088237.html

Quoted 10 lines
[ 2619.199658] pciehp 0000:00:1c.3:pcie04: Card not present on Slot(3)
[ 2619.199666] pciehp 0000:00:1c.3:pcie04: slot(3): Link Down event
[ 2619.199674] pciehp 0000:00:1c.3:pcie04: Link Down event ignored on
slot(3): already powering off
[ 2619.199911] pci_bus 0000:06: busn_res: [bus 06-0c] is released
[ 2620.757928] pciehp 0000:00:1c.3:pcie04: Card present on Slot(3)
[ 2620.767950] pciehp 0000:00:1c.3:pcie04: slot(3): Link Up event
[ 2620.767985] pciehp 0000:00:1c.3:pcie04: Link Up event ignored on

slot(3): already powering on

pciehp reacted power off and on here, and...

Quoted 6 lines
[ 2620.876160] pci 0000:05:00.0: [1102:7006] type 01 class 0x060400
[ 2620.876426] pci 0000:05:00.0: supports D1 D2
[ 2620.876719] pci 0000:05:00.0: bridge configuration invalid ([bus
00-00]), reconfiguring
[ 2620.876928] pci_bus 0000:06: busn_res: can not insert [bus 06-ff]

under [bus 05-0c] (conflicts with (null) [bus 05-0c])

.... and something failed here for the PCI bridge device.

Quoted 25 lines
[ 2620.876967] pci 0000:06:00.0: [1102:0009] type 00 class 0x040300
[ 2620.877013] pci 0000:06:00.0: reg 0x10: [mem 0x00000000-0x00003fff]
[ 2620.877203] pci 0000:06:00.0: supports D1 D2
[ 2620.877443] pci 0000:05:00.0: PCI bridge to [bus 06-ff]
[ 2620.877462] pci 0000:05:00.0:   bridge window [io  0x0000-0x0fff]
[ 2620.877474] pci 0000:05:00.0:   bridge window [mem 0x00000000-0x000fffff]
[ 2620.877492] pci 0000:05:00.0:   bridge window [mem
0x00000000-0x000fffff 64bit pref]
[ 2620.877500] pci_bus 0000:06: busn_res: [bus 06-ff] end is updated to 06
[ 2620.877559] pci 0000:05:00.0: BAR 14: assigned [mem
0xf4300000-0xf43fffff]
[ 2620.877568] pci 0000:05:00.0: BAR 15: assigned [mem
0xf4000000-0xf40fffff 64bit pref]
[ 2620.877574] pci 0000:05:00.0: BAR 13: assigned [io  0x2000-0x2fff]
[ 2620.877582] pci 0000:06:00.0: BAR 0: assigned [mem 0xf4300000-0xf4303fff]
[ 2620.877595] pci 0000:05:00.0: PCI bridge to [bus 06]
[ 2620.877603] pci 0000:05:00.0:   bridge window [io  0x2000-0x2fff]
[ 2620.877618] pci 0000:05:00.0:   bridge window [mem 0xf4300000-0xf43fffff]
[ 2620.877630] pci 0000:05:00.0:   bridge window [mem
0xf4000000-0xf40fffff 64bit pref]
[ 2620.877647] pcieport 0000:00:1c.3: PCI bridge to [bus 05-0c]
[ 2620.877655] pcieport 0000:00:1c.3:   bridge window [io  0x2000-0x2fff]
[ 2620.877667] pcieport 0000:00:1c.3:   bridge window [mem
0xf4300000-0xf7efffff]
[ 2620.877677] pcieport 0000:00:1c.3:   bridge window [mem
Quoted 8 lines

0xf4000000-0xf40fffff 64bit pref]

[ 2620.877990] pci 0000:05:00.0: enabling device (0000 -> 0003)
[ 2620.878013] snd_hda_intel 0000:06:00.0: enabling device (0000 -> 0002)
[ 2620.882747] azx_single_wait_for_response: 108 callbacks suppressed
[ 2620.882753] snd_hda_intel 0000:06:00.0: Codec #1 probe error;
disabling it...
[ 2620.887052] snd_hda_intel 0000:06:00.0: no AFG or MFG node found
[ 2620.887058] snd_hda_intel 0000:06:00.0: no codecs initialized
Quoted 1 line

I've tried many kernels from 2.6 to 3.18 with similar results. Willing to retrieve more info. Thank you :)

It looks like you booted with the card already installed, then removed and reinstalled it. Did the card work at any point? If it worked before the hotplug, then we need to look for a hotplug problem. If it never worked, then we can ignore hotplug for now.

My guess is that the card never worked at all and hotplug isn't an issue here.

The pciehp messages above are a bit scary looking, but I don't think they actually show a problem. It looks like you booted with the ExpressCard present, and it was configured like this:

pci 0000:00:1c.3: PCI bridge to [bus 05-0c]

  pci 0000:00:1c.3:   bridge window [io  0x2000-0x2fff]
  pci 0000:00:1c.3:   bridge window [mem 0xf4300000-0xf7efffff]
  pci 0000:00:1c.3:   bridge window [mem 0xf4000000-0xf40fffff 64bit pref]

pci 0000:05:00.0: PCI bridge to [bus 06-0c]
pci 0000:05:00.0: bridge window [mem 0xf4300000-0xf43fffff]
pci 0000:06:00.0: [1102:0009] type 00 class 0x040300 pci 0000:06:00.0: reg 0x10: [mem 0xf4300000-0xf4303fff] pciehp 0000:00:1c.3:pcie04: Slot #3 AttnBtn- AttnInd- PwrInd-
PwrCtrl- MRL- Interlock- NoCompl- LLActRep+

The kernel didn't change anything on the device, but the driver complained:

snd_hda_intel 0000:06:00.0: Codec #1 probe error; disabling it... snd_hda_intel 0000:06:00.0: no AFG or MFG node found snd_hda_intel 0000:06:00.0: no codecs initialized

I assume the device is not working at this point. (Correct me if I'm wrong.) Some time later, at timestamp 2620, it looks like you unplugged and replugged the ExpressCard. We reconfigured the bridge and device like this:

pci 0000:05:00.0: PCI bridge to [bus 06]

  pci 0000:05:00.0:   bridge window [io  0x2000-0x2fff]
  pci 0000:05:00.0:   bridge window [mem 0xf4300000-0xf43fffff]
  pci 0000:05:00.0:   bridge window [mem 0xf4000000-0xf40fffff 64bit pref]

pci 0000:06:00.0: BAR 0: assigned [mem 0xf4300000-0xf4303fff]

This is slightly different than what we had initially:

- 05:00.0 bridge bus aperture is [bus 06] instead of [bus 06-0c]
- 05:00.0 bridge io aperture is enabled instead of disabled
- 05:00.0 bridge mem pref aperture is enabled instead of disabled

But none of these is a problem and the audio device itself at 06:00.0 is programmed identically to what we had initially. And it looks like the driver complains exactly the same way it did at boot-time. So I don't think this is related to hotplug.

Can you use a program like this:
http://cmp.felk.cvut.cz/~pisa/linux/rdwrmem.c to read some of the device registers, e.g., the ones mapped by BAR 0 at 0xf4300000? I don't know what the register layout is, but if you get all 0xff responses, that might indicate that the device isn't responding, either because we haven't enabled it correctly or we haven't routed that space correctly, or .... If you get any data that is NOT all ones, that means the device is responding.

Quoted 2 lines

Could you also collect the output of "lspci -vvs00:1c.3", "lspci -vvs05:000" and "lspci -vvs06:00.0"?

FYI, during the previous debug sessions, we found that the sound driver gets only 0xff for mapped register accesses, so I suggested to report to PCI devs. IIRC, the non-hotplug board with this chip worked in the past.

thanks,

Takashi

maintainer
#4 lore raw
Quoted 4 lines · Takashi Iwai

FYI, during the previous debug sessions, we found that the sound driver gets only 0xff for mapped register accesses, so I suggested to report to PCI devs. IIRC, the non-hotplug board with this chip worked in the past.

I skimmed the previous emails but I missed this part. Did you add instrumentation to the driver, or is it just obvious from the way the driver behaves that we're getting 0xff?

Bjorn

author
#5 lore raw
In reply to Bjorn Helgaas
Quoted 90 lines · Bjorn Helgaas

[+cc Takashi]

Quoted 1 line · Alnie

Hi, I am seeking feedback in regards to issues with a ExpressCard/54 audio card (http://www.notebookreview.com/notebookreview/creative-soundblaster-x-fi-xtreme-audio-for-notebook-review/) under Linux (same card has been working fine in Win 7). After recently having a conversation on alsa-devel about it, it was decided it seems to be a PCI issue. The "devices" in question....

Hi Alnie,

I'm sorry you're running into a problem, but thanks for the report!

Quoted 81 lines

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Flags: bus master, fast devsel, latency 0
Bus: primary=05, secondary=06, subordinate=0c, sec-latency=36
Memory behind bridge: f4300000-f43fffff
Capabilities: [50] Power Management version 3
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express PCI-Express to PCI/PCI-X Bridge, MSI 00
Capabilities: [100] Advanced Error Reporting

06:00.0 Audio device: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG
Subsystem: Creative Labs SB1040
Flags: bus master, fast Back2Back, medium devsel, latency 32, IRQ 19 Memory at f4300000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [dc] Power Management version 3
Kernel driver in use: snd_hda_intel

dmesg output... http://pastebin.com/66UE659K

and comments in regard to it... http://mailman.alsa-project.org/pipermail/alsa-devel/2015-February/088237.html

Quoted 10 lines
[ 2619.199658] pciehp 0000:00:1c.3:pcie04: Card not present on Slot(3)
[ 2619.199666] pciehp 0000:00:1c.3:pcie04: slot(3): Link Down event
[ 2619.199674] pciehp 0000:00:1c.3:pcie04: Link Down event ignored on
slot(3): already powering off
[ 2619.199911] pci_bus 0000:06: busn_res: [bus 06-0c] is released
[ 2620.757928] pciehp 0000:00:1c.3:pcie04: Card present on Slot(3)
[ 2620.767950] pciehp 0000:00:1c.3:pcie04: slot(3): Link Up event
[ 2620.767985] pciehp 0000:00:1c.3:pcie04: Link Up event ignored on

slot(3): already powering on

pciehp reacted power off and on here, and...

Quoted 6 lines
[ 2620.876160] pci 0000:05:00.0: [1102:7006] type 01 class 0x060400
[ 2620.876426] pci 0000:05:00.0: supports D1 D2
[ 2620.876719] pci 0000:05:00.0: bridge configuration invalid ([bus
00-00]), reconfiguring
[ 2620.876928] pci_bus 0000:06: busn_res: can not insert [bus 06-ff]

under [bus 05-0c] (conflicts with (null) [bus 05-0c])

.... and something failed here for the PCI bridge device.

Quoted 33 lines
[ 2620.876967] pci 0000:06:00.0: [1102:0009] type 00 class 0x040300
[ 2620.877013] pci 0000:06:00.0: reg 0x10: [mem 0x00000000-0x00003fff]
[ 2620.877203] pci 0000:06:00.0: supports D1 D2
[ 2620.877443] pci 0000:05:00.0: PCI bridge to [bus 06-ff]
[ 2620.877462] pci 0000:05:00.0:   bridge window [io  0x0000-0x0fff]
[ 2620.877474] pci 0000:05:00.0:   bridge window [mem 0x00000000-0x000fffff]
[ 2620.877492] pci 0000:05:00.0:   bridge window [mem
0x00000000-0x000fffff 64bit pref]
[ 2620.877500] pci_bus 0000:06: busn_res: [bus 06-ff] end is updated to 06
[ 2620.877559] pci 0000:05:00.0: BAR 14: assigned [mem
0xf4300000-0xf43fffff]
[ 2620.877568] pci 0000:05:00.0: BAR 15: assigned [mem
0xf4000000-0xf40fffff 64bit pref]
[ 2620.877574] pci 0000:05:00.0: BAR 13: assigned [io  0x2000-0x2fff]
[ 2620.877582] pci 0000:06:00.0: BAR 0: assigned [mem 0xf4300000-0xf4303fff]
[ 2620.877595] pci 0000:05:00.0: PCI bridge to [bus 06]
[ 2620.877603] pci 0000:05:00.0:   bridge window [io  0x2000-0x2fff]
[ 2620.877618] pci 0000:05:00.0:   bridge window [mem 0xf4300000-0xf43fffff]
[ 2620.877630] pci 0000:05:00.0:   bridge window [mem
0xf4000000-0xf40fffff 64bit pref]
[ 2620.877647] pcieport 0000:00:1c.3: PCI bridge to [bus 05-0c]
[ 2620.877655] pcieport 0000:00:1c.3:   bridge window [io  0x2000-0x2fff]
[ 2620.877667] pcieport 0000:00:1c.3:   bridge window [mem
0xf4300000-0xf7efffff]
[ 2620.877677] pcieport 0000:00:1c.3:   bridge window [mem
0xf4000000-0xf40fffff 64bit pref]
[ 2620.877990] pci 0000:05:00.0: enabling device (0000 -> 0003)
[ 2620.878013] snd_hda_intel 0000:06:00.0: enabling device (0000 -> 0002)
[ 2620.882747] azx_single_wait_for_response: 108 callbacks suppressed
[ 2620.882753] snd_hda_intel 0000:06:00.0: Codec #1 probe error;
disabling it...
[ 2620.887052] snd_hda_intel 0000:06:00.0: no AFG or MFG node found
[ 2620.887058] snd_hda_intel 0000:06:00.0: no codecs initialized
Quoted 8 lines
Quoted 1 line

I've tried many kernels from 2.6 to 3.18 with similar results. Willing to retrieve more info. Thank you :)

It looks like you booted with the card already installed, then removed and reinstalled it. Did the card work at any point? If it worked before the hotplug, then we need to look for a hotplug problem. If it never worked, then we can ignore hotplug for now.

My guess is that the card never worked at all and hotplug isn't an issue here.

Correct. The card has not worked at any point for me in Linux.

Quoted 44 lines

The pciehp messages above are a bit scary looking, but I don't think they actually show a problem. It looks like you booted with the ExpressCard present, and it was configured like this:

   pci 0000:00:1c.3: PCI bridge to [bus 05-0c]
   pci 0000:00:1c.3:   bridge window [io  0x2000-0x2fff]
   pci 0000:00:1c.3:   bridge window [mem 0xf4300000-0xf7efffff]
   pci 0000:00:1c.3:   bridge window [mem 0xf4000000-0xf40fffff 64bit pref]
   pci 0000:05:00.0: PCI bridge to [bus 06-0c]
   pci 0000:05:00.0:   bridge window [mem 0xf4300000-0xf43fffff]
   pci 0000:06:00.0: [1102:0009] type 00 class 0x040300
   pci 0000:06:00.0: reg 0x10: [mem 0xf4300000-0xf4303fff]
   pciehp 0000:00:1c.3:pcie04: Slot #3 AttnBtn- AttnInd- PwrInd-

PwrCtrl- MRL- Interlock- NoCompl- LLActRep+

The kernel didn't change anything on the device, but the driver complained:

snd_hda_intel 0000:06:00.0: Codec #1 probe error; disabling it... snd_hda_intel 0000:06:00.0: no AFG or MFG node found snd_hda_intel 0000:06:00.0: no codecs initialized

I assume the device is not working at this point. (Correct me if I'm wrong.) Some time later, at timestamp 2620, it looks like you unplugged and replugged the ExpressCard. We reconfigured the bridge and device like this:

   pci 0000:05:00.0: PCI bridge to [bus 06]
   pci 0000:05:00.0:   bridge window [io  0x2000-0x2fff]
   pci 0000:05:00.0:   bridge window [mem 0xf4300000-0xf43fffff]
   pci 0000:05:00.0:   bridge window [mem 0xf4000000-0xf40fffff 64bit pref]
   pci 0000:06:00.0: BAR 0: assigned [mem 0xf4300000-0xf4303fff]

This is slightly different than what we had initially:

- 05:00.0 bridge bus aperture is [bus 06] instead of [bus 06-0c]
- 05:00.0 bridge io aperture is enabled instead of disabled
- 05:00.0 bridge mem pref aperture is enabled instead of disabled

But none of these is a problem and the audio device itself at 06:00.0 is programmed identically to what we had initially. And it looks like the driver complains exactly the same way it did at boot-time. So I don't think this is related to hotplug.

Quoted 8 lines

Can you use a program like this:
http://cmp.felk.cvut.cz/~pisa/linux/rdwrmem.c to read some of the device registers, e.g., the ones mapped by BAR 0 at 0xf4300000? I don't know what the register layout is, but if you get all 0xff responses, that might indicate that the device isn't responding, either because we haven't enabled it correctly or we haven't routed that space correctly, or .... If you get any data that is NOT all ones, that means the device is responding.

I just compiled this but I'm a bit unfamiliar, sorry :( It is giving me "mmap error". Is this the what you are looking for?

./mem -N -m -s 0xf4000000
./mem: request seek to 4093640704, but -201326592 returned F4000000:FF

Quoted 2 lines

Could you also collect the output of "lspci -vvs00:1c.3"

00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-

	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=05, subordinate=0c, sec-latency=0
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: f4300000-f7efffff
	Prefetchable memory behind bridge: 00000000f4000000-00000000f40fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 

<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency
L0s <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+
BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #3, PowerLimit 6.500W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt+ HPIrq+ LinkChg+
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 4122
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=04 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB-
LinkType=MemMapped LinkValid+

			Addr:	00000000fed1c000
	Kernel driver in use: pcieport
Quoted 1 line

lspci -vvs05:000"

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-

	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=05, secondary=06, subordinate=0c, sec-latency=36
	Memory behind bridge: f4300000-f43fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- 

<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency
L0s <512ns, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-

Quoted 1 line

and "lspci -vvs06:00.0"?

06:00.0 Audio device: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG
Subsystem: Creative Labs SB1040
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B+ DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f4300000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [dc] Power Management version 3
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: snd_hda_intel

Quoted 2 lines

Bjorn

maintainer
#6 lore raw
Quoted 5 lines · Alnie

I just compiled this but I'm a bit unfamiliar, sorry :( It is giving me "mmap error". Is this the what you are looking for?

./mem -N -m -s 0xf4000000
./mem: request seek to 4093640704, but -201326592 returned

4093640704 (unsigned) = 0xf4000000, -201326592 (signed) = 0xf4000000, so this might be OK.

Quoted 1 line

F4000000:FF

That's the sort of thing I was looking for, but the mmap error concerns me, so I'm not confident that this tells us anything. Also, we should look at more of the space to make sure that we get 0xff when reading *anything* on the device.

Quoted 2 lines

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])

Interesting. The description looks backwards -- this is a PCIe to PCI bridge, not the other way around. I posted a fix for that at
https://pci-ids.ucw.cz/read/PC/1102/7006?action=list

Quoted 28 lines

Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=05, secondary=06, subordinate=0c, sec-latency=36
	Memory behind bridge: f4300000-f43fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-

<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit
Latency L0s <512ns, L1 <16us

Quoted 8 lines

ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq+ ACSViol-

This looks suspicious: the bridge logged an Unsupported Request error. Let's see if we can figure out if this error is left there by BIOS or if the PCI core or the driver or rdwrmem is doing something that causes it.

Can you try this:

- Boot without the snd_hda_intel driver at all
- Collect "lspci -vvs05:00.0" output
- Load snd_hda_intel
- Collect "lspci -vvs05:00.0" output
- Poke around with rdwr
- Collect "lspci -vvs05:00.0" output

Quoted 7 lines

UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-

author
#7 lore raw
Quoted 62 lines · Bjorn Helgaas
Quoted 5 lines · Alnie

I just compiled this but I'm a bit unfamiliar, sorry :( It is giving me "mmap error". Is this the what you are looking for?

./mem -N -m -s 0xf4000000
./mem: request seek to 4093640704, but -201326592 returned

4093640704 (unsigned) = 0xf4000000, -201326592 (signed) = 0xf4000000, so this might be OK.

Quoted 1 line

F4000000:FF

That's the sort of thing I was looking for, but the mmap error concerns me, so I'm not confident that this tells us anything. Also, we should look at more of the space to make sure that we get 0xff when reading *anything* on the device.

Quoted 2 lines

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])

Interesting. The description looks backwards -- this is a PCIe to PCI bridge, not the other way around. I posted a fix for that at
https://pci-ids.ucw.cz/read/PC/1102/7006?action=list

Quoted 28 lines

Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=05, secondary=06, subordinate=0c, sec-latency=36
	Memory behind bridge: f4300000-f43fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-

<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit
Latency L0s <512ns, L1 <16us

Quoted 8 lines

ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq+ ACSViol-

Quoted 8 lines

This looks suspicious: the bridge logged an Unsupported Request error. Let's see if we can figure out if this error is left there by BIOS or if the PCI core or the driver or rdwrmem is doing something that causes it.

Can you try this:

- Boot without the snd_hda_intel driver at all
- Collect "lspci -vvs05:00.0" output

blacklist snd_hda_intel

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-

	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=05, secondary=06, subordinate=0c, sec-latency=36
	Memory behind bridge: f4300000-f43fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- 

<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency
L0s <512ns, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-

Quoted 2 lines

- Load snd_hda_intel
- Collect "lspci -vvs05:00.0" output

sudo modprobe snd-hda-intel

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-

	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=05, secondary=06, subordinate=0c, sec-latency=36
	Memory behind bridge: f4300000-f43fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- 

<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency
L0s <512ns, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-

(output looks identical)

Quoted 1 line

- Poke around with rdwr

(I am unfamiliar with this & hex, was trying different things, please correct me in case)

# ./mem -N -m -s 0xf4300000
./mem: request seek to 4096786432, but -198180864 returned
F4300000:00
# ./mem -N -m -s f4300000
00000000:53
# ./mem -N -m -s f4310000
00000000:53
# ./mem -N -m -s 0xf4310000
./mem: request seek to 4096851968, but -198115328 returned
F4310000:FF
Quoted 2 lines

- Collect "lspci -vvs05:00.0" output

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-

	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=05, secondary=06, subordinate=0c, sec-latency=36
	Memory behind bridge: f4300000-f43fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- 

<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency
L0s <512ns, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-

(output looks identical again)

maintainer
#8 lore raw
Quoted 16 lines · Alnie
Quoted 6 lines · Bjorn Helgaas
Quoted 3 lines · Alnie

Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq+ ACSViol-

Quoted 8 lines

This looks suspicious: the bridge logged an Unsupported Request error. Let's see if we can figure out if this error is left there by BIOS or if the PCI core or the driver or rdwrmem is doing something that causes it.

Can you try this:

- Boot without the snd_hda_intel driver at all
- Collect "lspci -vvs05:00.0" output

Quoted 8 lines

blacklist snd_hda_intel

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
...
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq+ ACSViol-

All three of your lspci outputs are identical, so it looks like the BIOS probably left UnsupReq set. Maybe the kernel should log that and clear it at boot. I sort of doubt this is the problem, but we can try clearing those errors manually:

lspci -vvs05:00.0
setpci -s05:00.0 0x9a.w=0x0a # clear UncorrErr UnsuppReq
setpci -s05:00.0 0x104.l=0x00100000 # clear AER UnsupReq
lspci -vvs05:00.0
modprobe snd-hda-intel

Quoted 5 lines
Quoted 1 line

- Poke around with rdwr

(I am unfamiliar with this & hex, was trying different things, please correct me in case)

Quoted 10 lines
# ./mem -N -m -s 0xf4300000
./mem: request seek to 4096786432, but -198180864 returned
F4300000:00
# ./mem -N -m -s f4300000
00000000:53
# ./mem -N -m -s f4310000
00000000:53
# ./mem -N -m -s 0xf4310000
./mem: request seek to 4096851968, but -198115328 returned
F4310000:FF

The first and last ones are on the right track. The program uses strtoul() to convert the address. That function assumes decimal unless there's a "0x" prefix. So "-s f4300000" converts to zero, and "-s 0xf4300000" does what you want.

The device is at [mem 0xf4300000-0xf4303fff], so anything in that region should respond. Why don't you try this, which should dump the whole region:

./mem -N -m -s 0xf4300000 -l 0x4000

But what's interesting already is that you found these:

F4300000:00
F4310000:FF

So we got 0x00 at 0xf4300000, which means the device did respond there. If that path to the device works, all PCI accesses to it *should* work.

Bjorn

author
#9 lore raw
Quoted 26 lines · Bjorn Helgaas
Quoted 16 lines · Alnie
Quoted 6 lines · Bjorn Helgaas
Quoted 3 lines · Alnie

Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq+ ACSViol-

Quoted 8 lines

This looks suspicious: the bridge logged an Unsupported Request error. Let's see if we can figure out if this error is left there by BIOS or if the PCI core or the driver or rdwrmem is doing something that causes it.

Can you try this:

- Boot without the snd_hda_intel driver at all
- Collect "lspci -vvs05:00.0" output

Quoted 8 lines

blacklist snd_hda_intel

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
...
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq+ ACSViol-

Quoted 6 lines

All three of your lspci outputs are identical, so it looks like the BIOS probably left UnsupReq set. Maybe the kernel should log that and clear it at boot. I sort of doubt this is the problem, but we can try clearing those errors manually:

   lspci -vvs05:00.0

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-

	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=05, secondary=06, subordinate=0c, sec-latency=36
	Memory behind bridge: f4300000-f43fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- 

<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency
L0s <512ns, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-

Quoted 3 lines
   setpci -s05:00.0 0x9a.w=0x0a		# clear UncorrErr UnsuppReq
   setpci -s05:00.0 0x104.l=0x00100000	# clear AER UnsupReq
   lspci -vvs05:00.0

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-

	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=05, secondary=06, subordinate=0c, sec-latency=36
	Memory behind bridge: f4300000-f43fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- 

<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency
L0s <512ns, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-

Quoted 2 lines

modprobe snd-hda-intel

Same complaint comes up (no codecs found)

Quoted 21 lines
Quoted 5 lines
Quoted 1 line

- Poke around with rdwr

(I am unfamiliar with this & hex, was trying different things, please correct me in case)

Quoted 10 lines
# ./mem -N -m -s 0xf4300000
./mem: request seek to 4096786432, but -198180864 returned
F4300000:00
# ./mem -N -m -s f4300000
00000000:53
# ./mem -N -m -s f4310000
00000000:53
# ./mem -N -m -s 0xf4310000
./mem: request seek to 4096851968, but -198115328 returned
F4310000:FF

The first and last ones are on the right track. The program uses strtoul() to convert the address. That function assumes decimal unless there's a "0x" prefix. So "-s f4300000" converts to zero, and "-s 0xf4300000" does what you want.

Quoted 6 lines

The device is at [mem 0xf4300000-0xf4303fff], so anything in that region should respond. Why don't you try this, which should dump the whole region:

   ./mem -N -m -s 0xf4300000 -l 0x4000

http://pastebin.com/eHEsZNmU

Quoted 10 lines

But what's interesting already is that you found these:

   F4300000:00
   F4310000:FF

So we got 0x00 at 0xf4300000, which means the device did respond there. If that path to the device works, all PCI accesses to it *should* work.

Bjorn

maintainer
#10 lore raw
Quoted 133 lines · Alnie
Quoted 26 lines · Bjorn Helgaas
Quoted 16 lines · Alnie
Quoted 6 lines · Bjorn Helgaas
Quoted 3 lines · Alnie

Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq+ ACSViol-

Quoted 8 lines

This looks suspicious: the bridge logged an Unsupported Request error. Let's see if we can figure out if this error is left there by BIOS or if the PCI core or the driver or rdwrmem is doing something that causes it.

Can you try this:

- Boot without the snd_hda_intel driver at all
- Collect "lspci -vvs05:00.0" output

Quoted 8 lines

blacklist snd_hda_intel

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
...
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq+ ACSViol-

Quoted 6 lines

All three of your lspci outputs are identical, so it looks like the BIOS probably left UnsupReq set. Maybe the kernel should log that and clear it at boot. I sort of doubt this is the problem, but we can try clearing those errors manually:

lspci -vvs05:00.0

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=05, secondary=06, subordinate=0c, sec-latency=36
	Memory behind bridge: f4300000-f43fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-

<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit
Latency L0s <512ns, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-

Quoted 3 lines

setpci -s05:00.0 0x9a.w=0x0a # clear UncorrErr UnsuppReq
setpci -s05:00.0 0x104.l=0x00100000 # clear AER UnsupReq
lspci -vvs05:00.0

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=05, secondary=06, subordinate=0c, sec-latency=36
	Memory behind bridge: f4300000-f43fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-

<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit
Latency L0s <512ns, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-

Quoted 4 lines
Quoted 2 lines

modprobe snd-hda-intel

Same complaint comes up (no codecs found)

So it looks like the Unsupported Request error is unrelated to the problem you're seeing. Probably left over from something the BIOS did when it enumerated devices.

You could look at "lspci -vv" again after clearing the errors and loading the driver. But I think it will be the same as it was after you manually cleared the errors.

Oh, one more idea: *before* clearing the errors, can you collect "lspci -xxxxs05:00.0" output? That will give us more AER log registers, and it's possible there's a clue there. It's conceivable that we have an MPS issue that causes the Unsupported Request error.

Just to be exhaustive, can you also stash the "lspci -vvv" output for the entire system somewhere (again, before clearing the error).

Quoted 8 lines
Quoted 6 lines

The device is at [mem 0xf4300000-0xf4303fff], so anything in that region should respond. Why don't you try this, which should dump the whole region:

./mem -N -m -s 0xf4300000 -l 0x4000

http://pastebin.com/eHEsZNmU

The data there looks fine, at least from a PCI perspective:

F4300000:00 33 00 01 3C 00 1D 00 01 00 00 00 00 00 00 00 F4300010:00 00 00 00 00 00 00 00 3C 00 1D 00 00 00 00 00 F4300020:00 00 00 C0 00 00 00 00 00 00 00 00 00 00 00 00 F4300030:0F FA 24 A8 00 00 00 00 00 00 00 00 00 00 00 00
...

That means the device itself seems happy and is responding to read requests.

The only thing left I can think of to do is to instrument the driver and see where it gets data that it doesn't expect. So I'm going to punt this back to you, Takashi :) Don't hesitate to send it back to me if you find something that looks like a PCI problem, but I don't see one yet.

Bjorn

author
#11 lore raw
Quoted 8 lines · Bjorn Helgaas

So it looks like the Unsupported Request error is unrelated to the problem you're seeing. Probably left over from something the BIOS did when it enumerated devices.

You could look at "lspci -vv" again after clearing the errors and loading the driver. But I think it will be the same as it was after you manually cleared the errors.

(after clearing errors) http://pastebin.com/UxdgDyp1

Quoted 5 lines

Oh, one more idea: *before* clearing the errors, can you collect "lspci -xxxxs05:00.0" output? That will give us more AER log registers, and it's possible there's a clue there. It's conceivable that we have an MPS issue that causes the Unsupported Request error.

(before clearing errors w/ card in @ boot) http://pastebin.com/wTeNjHHT
(before clearing errors w/ card out @ boot) http://pastebin.com/4Q82KNNc

Quoted 4 lines

Just to be exhaustive, can you also stash the "lspci -vvv" output for the entire system somewhere (again, before clearing the error).

http://pastebin.com/K4iPhGcq

not sure if this is relevant but for debugging sake here is the output of the card when left out during boot (no UnsupReq error)...

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-

	Bus: primary=05, secondary=06, subordinate=06, sec-latency=0
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: f8000000-f80fffff
	Prefetchable memory behind bridge: 00000000f4000000-00000000f40fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- 

<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency
L0s <512ns, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-

Quoted 27 lines
Quoted 8 lines
Quoted 6 lines

The device is at [mem 0xf4300000-0xf4303fff], so anything in that region should respond. Why don't you try this, which should dump the whole region:

   ./mem -N -m -s 0xf4300000 -l 0x4000

http://pastebin.com/eHEsZNmU

The data there looks fine, at least from a PCI perspective:

   F4300000:00 33 00 01 3C 00 1D 00 01 00 00 00 00 00 00 00
   F4300010:00 00 00 00 00 00 00 00 3C 00 1D 00 00 00 00 00
   F4300020:00 00 00 C0 00 00 00 00 00 00 00 00 00 00 00 00
   F4300030:0F FA 24 A8 00 00 00 00 00 00 00 00 00 00 00 00
   ...

That means the device itself seems happy and is responding to read requests.

The only thing left I can think of to do is to instrument the driver and see where it gets data that it doesn't expect. So I'm going to punt this back to you, Takashi :) Don't hesitate to send it back to me if you find something that looks like a PCI problem, but I don't see one yet.

Bjorn

author
#12 lore raw
Quoted 111 lines · Alnie
Quoted 9 lines · Bjorn Helgaas

So it looks like the Unsupported Request error is unrelated to the problem
you're seeing. Probably left over from something the BIOS did when it enumerated devices.

You could look at "lspci -vv" again after clearing the errors and loading the driver. But I think it will be the same as it was after you manually cleared the errors.

(after clearing errors) http://pastebin.com/UxdgDyp1

Quoted 5 lines

Oh, one more idea: *before* clearing the errors, can you collect "lspci -xxxxs05:00.0" output? That will give us more AER log registers, and it's possible there's a clue there. It's conceivable that we have an MPS issue that causes the Unsupported Request error.

(before clearing errors w/ card in @ boot) http://pastebin.com/wTeNjHHT
(before clearing errors w/ card out @ boot) http://pastebin.com/4Q82KNNc

Quoted 4 lines

Just to be exhaustive, can you also stash the "lspci -vvv" output for the entire system somewhere (again, before clearing the error).

http://pastebin.com/K4iPhGcq

not sure if this is relevant but for debugging sake here is the output of the card when left out during boot (no UnsupReq error)...

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

     Bus: primary=05, secondary=06, subordinate=06, sec-latency=0
     I/O behind bridge: 00002000-00002fff
     Memory behind bridge: f8000000-f80fffff
     Prefetchable memory behind bridge: 00000000f4000000-00000000f40fffff
     Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-

<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge,
MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit
Latency L0s <512ns, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-

Quoted 26 lines
Quoted 9 lines
Quoted 7 lines

The device is at [mem 0xf4300000-0xf4303fff], so anything in that region
should respond. Why don't you try this, which should dump the whole region:

   ./mem -N -m -s 0xf4300000 -l 0x4000

http://pastebin.com/eHEsZNmU

The data there looks fine, at least from a PCI perspective:

   F4300000:00 33 00 01 3C 00 1D 00 01 00 00 00 00 00 00 00
   F4300010:00 00 00 00 00 00 00 00 3C 00 1D 00 00 00 00 00
   F4300020:00 00 00 C0 00 00 00 00 00 00 00 00 00 00 00 00
   F4300030:0F FA 24 A8 00 00 00 00 00 00 00 00 00 00 00 00
   ...

That means the device itself seems happy and is responding to read requests.

The only thing left I can think of to do is to instrument the driver and see where it gets data that it doesn't expect. So I'm going to punt this back to you, Takashi :) Don't hesitate to send it back to me if you find something that looks like a PCI problem, but I don't see one yet.

Quoted 6 lines
Quoted 2 lines

Bjorn

--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Today I booted up into Win 7 and the card wasn't recognized. This is the first time I've noticed this. After re-inserting it, everything was fine, but I thought to take note. Maybe some of the issues coming up are unique to my hardware. Any new ideas? Is there hope for this? Should this conversation be moved elsewhere?

-Alnie

maintainer
#13 lore raw
Quoted 117 lines · Alnie
Quoted 116 lines · Alnie
Quoted 9 lines · Bjorn Helgaas

So it looks like the Unsupported Request error is unrelated to the problem
you're seeing. Probably left over from something the BIOS did when it enumerated devices.

You could look at "lspci -vv" again after clearing the errors and loading the driver. But I think it will be the same as it was after you manually cleared the errors.

(after clearing errors) http://pastebin.com/UxdgDyp1

Quoted 5 lines

Oh, one more idea: *before* clearing the errors, can you collect "lspci -xxxxs05:00.0" output? That will give us more AER log registers, and it's possible there's a clue there. It's conceivable that we have an MPS issue that causes the Unsupported Request error.

(before clearing errors w/ card in @ boot) http://pastebin.com/wTeNjHHT
(before clearing errors w/ card out @ boot) http://pastebin.com/4Q82KNNc

Quoted 4 lines

Just to be exhaustive, can you also stash the "lspci -vvv" output for the entire system somewhere (again, before clearing the error).

http://pastebin.com/K4iPhGcq

not sure if this is relevant but for debugging sake here is the output of the card when left out during boot (no UnsupReq error)...

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

     Bus: primary=05, secondary=06, subordinate=06, sec-latency=0
     I/O behind bridge: 00002000-00002fff
     Memory behind bridge: f8000000-f80fffff
     Prefetchable memory behind bridge: 00000000f4000000-00000000f40fffff
     Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-

<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge,
MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit
Latency L0s <512ns, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+
ChkEn-

Quoted 27 lines
Quoted 9 lines
Quoted 7 lines

The device is at [mem 0xf4300000-0xf4303fff], so anything in that region
should respond. Why don't you try this, which should dump the whole region:

   ./mem -N -m -s 0xf4300000 -l 0x4000

http://pastebin.com/eHEsZNmU

The data there looks fine, at least from a PCI perspective:

   F4300000:00 33 00 01 3C 00 1D 00 01 00 00 00 00 00 00 00
   F4300010:00 00 00 00 00 00 00 00 3C 00 1D 00 00 00 00 00
   F4300020:00 00 00 C0 00 00 00 00 00 00 00 00 00 00 00 00
   F4300030:0F FA 24 A8 00 00 00 00 00 00 00 00 00 00 00 00
   ...

That means the device itself seems happy and is responding to read requests.

The only thing left I can think of to do is to instrument the driver and see where it gets data that it doesn't expect. So I'm going to punt this back to you, Takashi :) Don't hesitate to send it back to me if you find something that looks like a PCI problem, but I don't see one yet.

Quoted 7 lines
Quoted 1 line
Quoted 1 line

Bjorn

Today I booted up into Win 7 and the card wasn't recognized. This is the first time I've noticed this. After re-inserting it, everything was fine, but I thought to take note. Maybe some of the issues coming up are unique to my hardware. Any new ideas? Is there hope for this? Should this conversation be moved elsewhere?

After you re-inserted the card, does it work after cold-booting Win 7?
If so, maybe it's an intermittent problem with the slot connector.

If you have to remove and re-insert the card *every* time you boot Win 7, maybe there's a problem on the card, e.g., it doesn't come out of reset fast enough.

I looked again at the Unsupported Request error that was logged, and I really don't think it's related. The header from the offending transaction was logged, and it looked like a Config Read request. It's normal for these reads to fail during enumeration. From the PCIe spec (r3.0, sec 2.3.2):

Some system configuration software depends on reading a data value of all 1’s when a Configuration Read Request is terminated as an Unsupported Request, particularly when probing to determine the existence of a device in the system. A Root Complex intended for use with software that depends on a read-data value of all 1’s must synthesize this value when UR Completion Status is returned for a Configuration Read Request.

It is a bit strange that this error is only logged when the card is present. I suspect the error is always logged during enumeration, but the BIOS may smart enough to clear it from the built-in bridges, but not smart enough to clear it on the bridge that's on the ExpressCard.

In any event, I still don't see a PCI issue here. I intended to open a bugzilla and attach the information you've collected in case somebody else can make sense out of it. But I haven't had time yet.

Bjorn

author
#14 lore raw
Quoted 152 lines · Bjorn Helgaas
Quoted 117 lines · Alnie
Quoted 116 lines · Alnie
Quoted 9 lines · Bjorn Helgaas

So it looks like the Unsupported Request error is unrelated to the problem
you're seeing. Probably left over from something the BIOS did when it enumerated devices.

You could look at "lspci -vv" again after clearing the errors and loading the driver. But I think it will be the same as it was after you manually cleared the errors.

(after clearing errors) http://pastebin.com/UxdgDyp1

Quoted 5 lines

Oh, one more idea: *before* clearing the errors, can you collect "lspci -xxxxs05:00.0" output? That will give us more AER log registers, and it's possible there's a clue there. It's conceivable that we have an MPS issue that causes the Unsupported Request error.

(before clearing errors w/ card in @ boot) http://pastebin.com/wTeNjHHT
(before clearing errors w/ card out @ boot) http://pastebin.com/4Q82KNNc

Quoted 4 lines

Just to be exhaustive, can you also stash the "lspci -vvv" output for the entire system somewhere (again, before clearing the error).

http://pastebin.com/K4iPhGcq

not sure if this is relevant but for debugging sake here is the output of the card when left out during boot (no UnsupReq error)...

05:00.0 PCI bridge: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG PCI to PCIe Bridge (prog-if 00 [Normal decode])
Physical Slot: 3
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

      Bus: primary=05, secondary=06, subordinate=06, sec-latency=0
      I/O behind bridge: 00002000-00002fff
      Memory behind bridge: f8000000-f80fffff
      Prefetchable memory behind bridge: 00000000f4000000-00000000f40fffff
      Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-

<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Creative Labs Device 0040
Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge,
MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit
Latency L0s <512ns, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+
ChkEn-

Quoted 27 lines
Quoted 9 lines
Quoted 7 lines

The device is at [mem 0xf4300000-0xf4303fff], so anything in that region
should respond. Why don't you try this, which should dump the whole region:

    ./mem -N -m -s 0xf4300000 -l 0x4000

http://pastebin.com/eHEsZNmU

The data there looks fine, at least from a PCI perspective:

    F4300000:00 33 00 01 3C 00 1D 00 01 00 00 00 00 00 00 00
    F4300010:00 00 00 00 00 00 00 00 3C 00 1D 00 00 00 00 00
    F4300020:00 00 00 C0 00 00 00 00 00 00 00 00 00 00 00 00
    F4300030:0F FA 24 A8 00 00 00 00 00 00 00 00 00 00 00 00
    ...

That means the device itself seems happy and is responding to read requests.

The only thing left I can think of to do is to instrument the driver and see where it gets data that it doesn't expect. So I'm going to punt this back to you, Takashi :) Don't hesitate to send it back to me if you find something that looks like a PCI problem, but I don't see one yet.

Quoted 7 lines
Quoted 1 line
Quoted 1 line

Bjorn

Today I booted up into Win 7 and the card wasn't recognized. This is the first time I've noticed this. After re-inserting it, everything was fine, but I thought to take note. Maybe some of the issues coming up are unique to my hardware. Any new ideas? Is there hope for this? Should this conversation be moved elsewhere?

After you re-inserted the card, does it work after cold-booting Win 7?
If so, maybe it's an intermittent problem with the slot connector.

If you have to remove and re-insert the card *every* time you boot Win 7, maybe there's a problem on the card, e.g., it doesn't come out of reset fast enough.

I looked again at the Unsupported Request error that was logged, and I really don't think it's related. The header from the offending transaction was logged, and it looked like a Config Read request. It's normal for these reads to fail during enumeration. From the PCIe spec (r3.0, sec 2.3.2):

Some system configuration software depends on reading a data value of all 1’s when a Configuration Read Request is terminated as an Unsupported Request, particularly when probing to determine the existence of a device in the system. A Root Complex intended for use with software that depends on a read-data value of all 1’s must synthesize this value when UR Completion Status is returned for a Configuration Read Request.

It is a bit strange that this error is only logged when the card is present. I suspect the error is always logged during enumeration, but the BIOS may smart enough to clear it from the built-in bridges, but not smart enough to clear it on the bridge that's on the ExpressCard.

Quoted 6 lines

In any event, I still don't see a PCI issue here. I intended to open a bugzilla and attach the information you've collected in case somebody else can make sense out of it. But I haven't had time yet.

Bjorn

Yes, it seems like just a intermittent problem with the slot connector Most of the time it works fine. Thank you very much for being so informative and taking the time to look into this :)

-Alnie