Skip to contentSkip to conversation

sound/soc/atmel: Add slave mode support to SSC in DSP Mode A

PATCH Applied Zoltan Puskas 2 participants 2 messages Feb 20, 2013

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 sound/soc/atmel: Add slave mode support to SSC in DSP Mode A

From: Zoltan Puskas <[email protected]>

Add previously unsupported slave mode to the SSC peripheral when using DSP/PCM Mode A format on the Atmel ARM platform.

---
The code was tested using WM8804 and WM8731 digital sound chips, using 3.7.9 and 3.3.1 kernels on a system with AT91SAM9261 CPU on board.

sound/soc/atmel/atmel_ssc_dai.c renamed from sound/soc/atmel/atmel_ssc_dai.c.orig +43 -0
@@ -543,6 +543,49 @@ static int atmel_ssc_hw_params(struct sn
 		break;
 
 	case SND_SOC_DAIFMT_DSP_A | SND_SOC_DAIFMT_CBM_CFM:
+		/*
+		 * DSP/PCM Mode A format, CODEC supplies BCLK and LRC clocks.
+		 *
+		 * The SSC transmit clock is obtained from the BCLK signal on
+		 * on the TK line, and the SSC receive clock is
+		 * generated from the transmit clock.
+		 *
+		 * Data is transferred on first BCLK after LRC pulse rising
+		 * edge.If stereo, the right channel data is contiguous with
+		 * the left channel data.
+		 */
+		rcmr =	  SSC_BF(RCMR_PERIOD, 0)
+			| SSC_BF(RCMR_STTDLY, START_DELAY)
+			| SSC_BF(RCMR_START, SSC_START_RISING_RF)
+			| SSC_BF(RCMR_CKI, SSC_CKI_RISING)
+			| SSC_BF(RCMR_CKO, SSC_CKO_NONE)
+			| SSC_BF(RCMR_CKS, SSC_CKS_PIN);
+
+		rfmr =	  SSC_BF(RFMR_FSEDGE, SSC_FSEDGE_POSITIVE)
+			| SSC_BF(RFMR_FSOS, SSC_FSOS_NONE)
+			| SSC_BF(RFMR_FSLEN, 0)
+			| SSC_BF(RFMR_DATNB, (channels - 1))
+			| SSC_BIT(RFMR_MSBF)
+			| SSC_BF(RFMR_LOOP, 0)
+			| SSC_BF(RFMR_DATLEN, (bits - 1));
+
+		tcmr =	  SSC_BF(TCMR_PERIOD, 0)
+			| SSC_BF(TCMR_STTDLY, START_DELAY)
+			| SSC_BF(TCMR_START, SSC_START_RISING_RF)
+			| SSC_BF(TCMR_CKI, SSC_CKI_FALLING)
+			| SSC_BF(TCMR_CKO, SSC_CKO_NONE)
+			| SSC_BF(TCMR_CKS, SSC_CKS_PIN);
+
+		tfmr =	  SSC_BF(TFMR_FSEDGE, SSC_FSEDGE_POSITIVE)
+			| SSC_BF(TFMR_FSDEN, 0)
+			| SSC_BF(TFMR_FSOS, SSC_FSOS_NONE)
+			| SSC_BF(TFMR_FSLEN, 0)
+			| SSC_BF(TFMR_DATNB, (channels - 1))
+			| SSC_BIT(TFMR_MSBF)
+			| SSC_BF(TFMR_DATDEF, 0)
+			| SSC_BF(TFMR_DATLEN, (bits - 1));
+		break;
+
 	default:
 		printk(KERN_WARNING "atmel_ssc_dai: unsupported DAI format 0x%x\n",
 			ssc_p->daifmt);
Applied
#1 lore raw
Quoted 4 lines · Zoltan Puskas

From: Zoltan Puskas <[email protected]>

Add previously unsupported slave mode to the SSC peripheral when using DSP/PCM Mode A format on the Atmel ARM platform.

Applied, but please always use subject lines appropriate for the subsystem.