Skip to contentSkip to conversation

5.10.y-cip/arm : Add support for access control lists.

cip-dev [email protected] 2 participants 2 messages May 23, 2023 1 message not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

#1 lore raw

Hi all,

I request you to review this patch. Previously I sent a patch for acl package to work in arm architecture (IEC purpose) but in that I mistakenly added ext4 related POSIX_ACL config.

Sticking to the purpose of acl package to work, In the below patch I rectified that, and just added already existing EXT3 filesystem's POSIX_ACL config.

Kindly provide your review.

Thanks and regards,
Sai Ashrith (T S I P)

-----Original Message-----
From: [email protected] <[email protected]> On Behalf Of [email protected]
Sent: Tuesday, May 16, 2023 7:37 PM
To: [email protected]; iwamatsu nobuhiro(岩松 信洋 ○DITC□DIT○OST) <[email protected]>
Cc: ashrith sai(TSIP) <[email protected]>; dinesh kumar(TSIP TMIEC ODG Porting) <[email protected]>
Subject: [cip-dev] [cip-kernel-config] 5.10.y-cip/arm : Add support for access control lists.

From: Sai <[email protected]>

This config is required for acl package to work which is used for IEC-62443-4-2 evaluation.

---
 5.10.y-cip/arm/qemu_arm_defconfig | 1 +
 1 file changed, 1 insertion(+)
5.10.y-cip/arm/qemu_arm_defconfig +1 -0
index 58ca273..b8f4e88 100644
@@ -149,6 +149,7 @@ CONFIG_EXT2_FS=y
 CONFIG_EXT2_FS_XATTR=y
 CONFIG_EXT2_FS_POSIX_ACL=y
 CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
 CONFIG_AUTOFS4_FS=y
 CONFIG_FUSE_FS=m
 CONFIG_OVERLAY_FS=m

--
2.20.1

#2 lore raw

Hi ashrith sai,

Quoted 10 lines

-----Original Message-----
From: ashrith sai(TSIP) <[email protected]>
Sent: Tuesday, May 23, 2023 10:48 PM
To: [email protected]; iwamatsu nobuhiro(岩松 信洋 ○DITC□ DIT○OST) <[email protected]>
Cc: dinesh kumar(TSIP TMIEC ODG Porting) <[email protected]>
Subject: RE: [cip-dev] [cip-kernel-config] 5.10.y-cip/arm : Add support for access control lists.

Quoted 8 lines

Hi all,

I request you to review this patch. Previously I sent a patch for acl package to work in arm architecture (IEC purpose) but in that I mistakenly added ext4 related POSIX_ACL config.

Sticking to the purpose of acl package to work, In the below patch I rectified that, and just added already existing EXT3 filesystem's POSIX_ACL config.

I see. I applied, thanks.

Quoted 6 lines

Kindly provide your review.

Thanks and regards,
Sai Ashrith (T S I P)

Best regards,
Nobuhiro

Quoted 37 lines

-----Original Message-----
From: [email protected] <[email protected]> On Behalf Of [email protected]
Sent: Tuesday, May 16, 2023 7:37 PM
To: [email protected]; iwamatsu nobuhiro(岩松 信洋 ○DITC□ DIT○OST) <[email protected]>
Cc: ashrith sai(TSIP) <[email protected]>; dinesh kumar(TSIP TMIEC ODG Porting) <[email protected]>
Subject: [cip-dev] [cip-kernel-config] 5.10.y-cip/arm : Add support for access control lists.

From: Sai <[email protected]>

This config is required for acl package to work which is used for IEC-62443-4-2 evaluation.

---
 5.10.y-cip/arm/qemu_arm_defconfig | 1 +
 1 file changed, 1 insertion(+)
5.10.y-cip/arm/qemu_arm_defconfig +1 -1
index 58ca273..b8f4e88 100644
@@ -149,6 +149,7 @@ CONFIG_EXT2_FS=y
 CONFIG_EXT2_FS_XATTR=y
 CONFIG_EXT2_FS_POSIX_ACL=y
 CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
 CONFIG_AUTOFS4_FS=y
 CONFIG_FUSE_FS=m
 CONFIG_OVERLAY_FS=m
--

2.20.1