gpio: rcar: Support both edge trigger with DT
Subsystems (3)
PATCH RESEND 1/1 gpio: rcar: Support both edge trigger with DT
Some versions of the R-Car GPIO controller support triggering on both edges of the input signal. Whether this capability is supported is currently specified in platform data. R-Car GPIO devices instantiated from the device tree have the capability turned off even when the hardware supports it.
To fix this, add DT match data support to the driver, initialize both edge trigger support from match data and enable both edge trigger in r8a7790 and r8a7791 match data.
--- drivers/gpio/gpio-rcar.c | 56 +++++++++++++++++++++++++++++++++++++----------- 1 file changed, 43 insertions(+), 13 deletions(-)
(With the correct linux-sh address this time, sorry about the noise)
drivers/gpio/gpio-rcar.c +43 -13
@@ -284,7 +284,34 @@ static struct irq_domain_ops gpio_rcar_irq_domain_ops = { .map = gpio_rcar_irq_domain_map, }; -static void gpio_rcar_parse_pdata (struct gpio_rcar_priv *p) +struct gpio_rcar_info { +bool has_both_edge_trigger; +}; + +static const struct of_device_id gpio_rcar_of_table[] = { + { + .compatible ="renesas,gpio-r8a7790" , + .data = (void *)&(const struct gpio_rcar_info ) { + .has_both_edge_trigger = true, + }, + }, { + .compatible ="renesas,gpio-r8a7791" , + .data = (void *)&(const struct gpio_rcar_info ) { + .has_both_edge_trigger = true, + }, + }, { + .compatible ="renesas,gpio-rcar" , + .data = (void *)&(const struct gpio_rcar_info ) { + .has_both_edge_trigger = false, + }, + }, { +/* Terminator */ + }, +}; + +MODULE_DEVICE_TABLE (of, gpio_rcar_of_table); + +static int gpio_rcar_parse_pdata (struct gpio_rcar_priv *p) {struct gpio_rcar_config *pdata =dev_get_platdata (&p->pdev->dev);struct device_node *np = p->pdev->dev.of_node;
@@ -294,11 +321,21 @@ static void gpio_rcar_parse_pdata(struct gpio_rcar_priv *p)if (pdata) { p->config = *pdata; }else if (IS_ENABLED (CONFIG_OF ) && np) { +const struct of_device_id *match; +const struct gpio_rcar_info *info; + + match =of_match_node (gpio_rcar_of_table, np); +if (!match) +return -EINVAL ; + + info = match->data; + ret =of_parse_phandle_with_fixed_args (np,"gpio-ranges" ,3 ,0 , &args); p->config.number_of_pins = ret =0 ? args.args[2 ] :RCAR_MAX_GPIO_PER_BANK ; p->config.gpio_base =-1 ; + p->config.has_both_edge_trigger = info->has_both_edge_trigger; } if (p->config.number_of_pins = 0 ||
@@ -308,6 +345,8 @@ static void gpio_rcar_parse_pdata(struct gpio_rcar_priv *p) p->config.number_of_pins, RCAR_MAX_GPIO_PER_BANK); p->config.number_of_pins =RCAR_MAX_GPIO_PER_BANK ; } + +return 0 ; }static int gpio_rcar_probe (struct platform_device *pdev)
@@ -330,7 +369,9 @@ static int gpio_rcar_probe(struct platform_device *pdev)spin_lock_init (&p->lock);/* Get device configuration from DT node or platform data. */ -gpio_rcar_parse_pdata (p); + ret =gpio_rcar_parse_pdata (p); +if (ret <0 ) +return ret;platform_set_drvdata (pdev, p);
@@ -434,17 +475,6 @@ static int gpio_rcar_remove(struct platform_device *pdev)return 0 ; } -#ifdef CONFIG_OF -static const struct of_device_id gpio_rcar_of_table[] = { - { - .compatible ="renesas,gpio-rcar" , - }, - { }, -}; - -MODULE_DEVICE_TABLE (of, gpio_rcar_of_table); -#endif -static struct platform_driver gpio_rcar_device_driver = { .probe = gpio_rcar_probe, .remove = gpio_rcar_remove,
Signature · 3 lines
Regards, Laurent Pinchart
Quoted 6 lines · Laurent Pinchart
Some versions of the R-Car GPIO controller support triggering on both edges of the input signal. Whether this capability is supported is currently specified in platform data. R-Car GPIO devices instantiated from the device tree have the capability turned off even when the hardware supports it.
Quoted 6 lines
To fix this, add DT match data support to the driver, initialize both edge trigger support from match data and enable both edge trigger in r8a7790 and r8a7791 match data.
Signed-off-by Laurent Pinchart <[email protected]>Acked-by Magnus Damm <[email protected]>
Patch applied, but shouldn't there be some change to add these new compatible strings to Documentation/devicetree/bindings/* somewhere?
Accepted as follow-on patch or something to be squashed into this later if I'm right.
Thanks!
Linus Walleij
Hi Linus,
Quoted 11 lines · On Friday 29 November 2013 21:06:17 Linus Walleij wrote:
Quoted 10 lines · Laurent Pinchart
Some versions of the R-Car GPIO controller support triggering on both edges of the input signal. Whether this capability is supported is currently specified in platform data. R-Car GPIO devices instantiated from the device tree have the capability turned off even when the hardware supports it.
To fix this, add DT match data support to the driver, initialize both edge trigger support from match data and enable both edge trigger in r8a7790 and r8a7791 match data.
Quoted 7 lines
Quoted 3 lines
Signed-off-by: Laurent Pinchart
<[email protected]>Acked-by Magnus Damm <[email protected]>Patch applied, but shouldn't there be some change to add these new compatible strings to
Documentation/devicetree/bindings/*somewhere?
You're right.
Quoted 2 lines
Accepted as follow-on patch or something to be squashed into this later if I'm right.
Sent.
Signature · 3 lines
Regards, Laurent Pinchart