Skip to contentSkip to conversation

: No AC3/DTS via SPDIF on Intel 82801DB-ICH4 with CS4299

ALSA - driver 0000839 [email protected] 1 participant 1 message Jul 14, 2005

lore
Share & tools
lore
#0 lore raw

A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=839>
======================================================================
Reported By: Mimosius
Assigned To:
======================================================================

Project:                    ALSA - driver
Issue ID:                   839
Category:                   PCI - intel8x0
Reproducibility:            always
Severity:                   minor
Priority:                   normal
Status:                     new
Distribution:               SuSE 9.2
Kernel Version:             2.6.8-24.10 + 2.6.10
======================================================================
Date Submitted:             01-21-2005 03:12 CET
Last Modified:              07-14-2005 15:50 CEST

======================================================================
Summary: No AC3/DTS via SPDIF on Intel 82801DB-ICH4 with
CS4299
Description:
Audio-mode via SPDIF works fine but I can't get any non-audio passthru working.

Using 'ac3play -C test.ac3' SPDIF output is set to AES0=0x2 AES1=0x82 AES2=0x0 AES3=0x2 and the PCM indicator on external decoder turns off, but there seems to arrive no decodeable signal on receiver side. There are no errors or warnings after loading soundrivers and there are no other soundcards plugged in (notebook).

here are some system informations:

# cat /etc/modprobe.d/sound
alias snd-card-0 snd-intel8x0
options snd-ac97-codec
options snd-intel8x0 enable=1 index=0
# cat /proc/asound/pcm' 
00-00: Intel ICH : Intel 82801DB-ICH4 : playback 1 : capture 1
00-01: Intel ICH - MIC ADC : Intel 82801DB-ICH4 - MIC ADC : capture 1
00-02: Intel ICH - MIC2 ADC : Intel 82801DB-ICH4 - MIC2 ADC : capture 1
00-03: Intel ICH - ADC2 : Intel 82801DB-ICH4 - ADC2 : capture 1
00-04: Intel ICH - IEC958 : Intel 82801DB-ICH4 - IEC958 : playback 1
# cat /proc/asound/card0/codec97#0/ac97#0-0' (while playing ac3 using
ac3dec -C)
0-0/0: Cirrus Logic CS4299 rev 4

Capabilities : -headphone out-
DAC resolution : 20-bit
ADC resolution : 18-bit
3D enhancement : Crystal Semi 3D Stereo Enhancement

Current setup
Mic gain : +0dB [+0dB]
POP path : pre 3D
Sim. stereo : off

3D enhancement   : off
Loudness         : off
Mono output      : Mic
Mic select       : Mic1

ADC/DAC loopback : off
Extended ID : codec=0 rev=0 AMAP DSA=0 VRA
Extended status : VRA
PCM front DAC : 48000Hz
PCM ADC : 48000Hz
SPDIF Control : Consumer Non-audio Category=0x2 Generation=1 Rate=48kHz
Enabled

# cat /proc/asound/card0/codec97#0/ac97#0-0+regs (while playing ac3 using
ac3dec -C)
0:00 = 1990
0:02 = 3f3f
0:04 = 9f1f
0:06 = 801f
0:08 = 0000
0:0a = 801e
0:0c = 801f
0:0e = 8000
0:10 = 9f1f
0:12 = 9f1f
0:14 = 9f1f
0:16 = 9f1f
0:18 = 8000
0:1a = 0606
0:1c = 0f0f
0:1e = 0000
0:20 = 0200
0:22 = 0000
0:24 = 0000
0:26 = 800f
0:28 = 0201
0:2a = 0001
0:2c = bb80
0:2e = 0000
0:30 = 0000
0:32 = bb80
0:34 = 0000
0:36 = 0000
0:38 = 0000
0:3a = 0000
0:3c = 0000
0:3e = 0000
0:40 = 0000
0:42 = 0000
0:44 = 0000
0:46 = 0000
0:48 = 0000
0:4a = 0000
0:4c = 0000
0:4e = 0000
0:50 = 0000
0:52 = 0000
0:54 = 0000
0:56 = 0000
0:58 = 0000
0:5a = 0404
0:5c = 0000
0:5e = 0080
0:60 = 0022
0:62 = 0000
0:64 = 0000
0:66 = 0000
0:68 = 8826
0:6a = 0000
0:6c = 0000
0:6e = 0000
0:70 = 0000
0:72 = 0000
0:74 = 0000
0:76 = 0000
0:78 = 003f
0:7a = 0000
0:7c = 4352
0:7e = 5934

======================================================================

----------------------------------------------------------------------
Mimosius - 06-22-05 18:58
----------------------------------------------------------------------
Hi tiwai,

Quoted 4 lines

Well, two possibilities can be counted:
1. the SPDIF signal is sent through a wrong channel or recoded somehow wrongly, so the non-audio data is broken
2. the SPDIF non-audio status bit is not set. Some receivers are so

sentive >that they don't accept SPDIF signals with that.

I tried to play an AC3-file with mplayer using alsa-driver with hwac3 output and "ac3dec -C". Each test gives the same result, the value in register 0x68 changed from 0x8824 to 0x8826, which shows that the non-audio bit was set correctly.

Quoted 1 line

The latter happens more often, but I'm not sure which one (or both?) in

your case. The former one would be either:

Quoted 1 line

- you passed the data through the normal DMA via slot3/4, or

The AC Mode Control Register 0x5e is set to 0x80 which indicates slot assignment L3/R4 (Page 30 and Crystals Documentation). Maybe the DDM bit should also be set?

from Documentation:
"DDM: (DAC direct mode) This bit controls the source to the line and alternate line output drivers. When 'set' the L/R DACs directly drive the line and alternate line outputs by bypassing the audio mixer. When 'clear' the audio mixer is the source for the line and alternate line outputs."

Quoted 1 line

- wrong sample rate, not supported by the codec, or

PCM Front Rate Register 0x2c is set to 0xbb80 (48KHz)

As you said, there are maybe some recodings of the non-audio data. Is there any way to grab these data? (I still have a desktop system using a Hoontech with YMF754 and S/PDIF in.)
Is there a simple way to grab the AC97 registers of the Win32 Driver?

Regards
Glen

----------------------------------------------------------------------
mrbox - 07-14-05 15:50
----------------------------------------------------------------------
I have got exactly the same problem(s) only with a :
I82801CA-ICH3 with CS4205

the register also changes from 8820 to 8826 when playing ac3 file but i only get a "chopper" sound out of my speaker system (creative DTT 2500 ).

Issue History
Date Modified Username Field Change
======================================================================

01-21-05 03:12 Mimosius       New Issue                                    
01-21-05 03:12 Mimosius       Distribution              => SuSE 9.2        
01-21-05 03:12 Mimosius       Kernel Version            => 2.6.8-24.10 + 2.6.10
01-21-05 03:13 Mimosius       Issue Monitored: Mimosius                    
03-01-05 11:31 Mimosius       Note Added: 0003758                          
03-15-05 21:37 Mimosius       Note Added: 0003917                          
03-16-05 12:47 tiwai          Note Added: 0003945                          
03-16-05 12:47 tiwai          Note Added: 0003946                          
03-17-05 01:00 Mimosius       Note Added: 0003975                          
06-22-05 13:08 Mimosius       Note Added: 0005132                          
06-22-05 17:56 tiwai          Note Added: 0005137                          
06-22-05 18:58 Mimosius       Note Added: 0005143                          
07-14-05 15:50 mrbox          Note Added: 0005475                          

======================================================================

-------------------------------------------------------
This SF.Net email is sponsored by the 'Do More With Dual!' webinar happening July 14 at 8am PDT/11am EDT. We invite you to explore the latest in dual core and dual graphics technology at this free one hour event hosted by HP, AMD, and NVIDIA. To register visit http://www.hp.com/go/dualwebinar