Tags are dead alias Milo is dead part II
A message that is not in the archive (sent off-list or not yet received): [email protected]
[email protected]
AppliedQuoted 10 lines · Thomas Bogendoerfer
In the process of making Milo obsolete I've also removed tags stuff. This was simple for the Indy and took only a few hours for the Olivetti. I hope it's also possible for the Decstation. Before I'll start commiting the changes we should make sure, how to solve the missing tags for all plattforms.
Another old code, which might be obsolete now is the wired entry stuff in
arch/mips/kernel/head.S. It's already disabled for R4k CPUs and I would prefer to remove that stuff also for the other CPUs. If you need wired entries, I would propose using theadd_wired_entry()function as I already do it for the JAZZ hardware (arch/mips/jazz/setup.c).
People should consider that TLB entries are a scarce resource. Wiring them can seriously impact performance. (Which reminds me of the lock warning bit in the 68851 - Moto people we seriously assuming somebody could wire all ATC (that is TLB in Moto slang) entries ...)
Our current 32 bit page table structure is good for mapping everything in the lowest 4gb of physical address space. Things outside of this area are the only things which will need to be mapped by some other mean. We've so far used wired entries which in most cases they're a bad idea for the above mentioned reason. Since loading and flushing a single TLB entry is a quite cheap thing on MIPS parts of the kernel could do things like
struct wired {
caddr_t physical;
caddr_t virtual;
u32 mask;
u32 usage;
u8 entry;
} gfx_entry = {
GFX_PBASE,
GFX_VBASE,
PM_4M
};
entry = load_wired_entry(&gfx_entry);
... /* Munge mapped address space */
flush_wired_entry(entry);Applied to the G364 drivers (which as of now is still MIPS specific anyway) this means that we'll avoid TLB trashing in the case of scrolling and have the full TLB available for userland.
The second alternative which can be used where it's ok to disable interrupts is to access memory using one of the XKPHYS segments.
Ralf
Thomas Bogendoerfer
maintainerQuoted 3 lines · On Thu, Oct 08, 1998 at 05:03:35PM +0200, [email protected] wrote:
Applied to the G364 drivers (which as of now is still MIPS specific anyway) this means that we'll avoid TLB trashing in the case of scrolling and have the full TLB available for userland.
I don't believe this will buy us anything. When we add a temporary TLB we need do clear one TLB, which might be used by the userland. So we end up loading our wired entry, killing it, and later the user process has to reload the TLB again. This way we force TLB trashing, with one wired entry more we _might_ get a little bit more TLB trashing.
As you might know, I'm using three wired entries for the Magnum, and I don't think doing the same trick for the other entries is a real good idea. When we make them temporary, we have to mess with TLBs on every interrupt.
Thomas.
Signature · 3 lines
This device has completely bogus header. Compaq scores again :-|
It's a host bridge, but it should be called ghost bridge instead ;^)
[Martin `MJ' Mares on linux-kernel]Quoted 11 lines · Thomas Bogendoerfer
Quoted 3 lines · On Thu, Oct 08, 1998 at 05:03:35PM +0200, [email protected] wrote:
Applied to the G364 drivers (which as of now is still MIPS specific anyway) this means that we'll avoid TLB trashing in the case of scrolling and have the full TLB available for userland.
I don't believe this will buy us anything. When we add a temporary TLB we need do clear one TLB, which might be used by the userland. So we end up loading our wired entry, killing it, and later the user process has to reload the TLB again. This way we force TLB trashing, with one wired entry more we _might_ get a little bit more TLB trashing.
Quoted 3 lines
As you might know, I'm using three wired entries for the Magnum, and I don't think doing the same trick for the other entries is a real good idea. When we make them temporary, we have to mess with TLBs on every interrupt.
You could do what IRIX does in some cases, which is to save and restore
the TLB entry you replace. Beware of doing this, however, if your code could take a page fault.