Skip to contentSkip to conversation

CDROM Problems with 2.2.9

DISCUSSION roboj 2 participants 3 messages May 14, 1999 – May 24, 1999 1 message not in the archive

lore
Share & tools
lore

roboj

author
#1 lore raw
In reply to a message not in the archive

After compiling the recent linux kernel (2.2.9), I've been getting an error message which I have included below. I get it at boot time and it continues printing in an infinite loop. Also, the computer seems to be trying to access my cd-rom drive (Toshiba scsi, /dev/scd0 linked to /dev/cdrom). Running power computing powerbase. Anyone ever got a similar error message that can offer any suggestions? Everything works ok in linux vers. 2.2.6-ac3.

SCSI: aborting command due to timeout pid 3, scsi 0, channel 0, id 1

mesh_abort (c0374000)
mesh: state at c0374278, regs at f3010000 dma at f3008000
ct = 0, seq = c , bs = 6000, fc = 0, exc = 0, err = 0, im = 7, int = 0, sp = 2, dma stat = c0, cmdptr = 364010, phase = 0, msgphase = 0, comm_tgt = 1, data_ptr = 0, dma_st = 0, dma_ct = 0, n_msgout = 0

target 1: req = 0374000 goes_out = 0, saved_ptr = 0

SCSI Host 0 abort (pid3) timed out - resetting
SCSI bus is being reset for host 0 channel 0

mesh reset 2
mesh: SCSI bus reset detected: waiting for end...done

[[ This message was sent via the linuxppc-dev mailing list. Replies are ]] [[ not forced back to the list, so be sure to Cc linuxppc-dev if your ]] [[ reply is of general interest. Please check http://lists.linuxppc.org/ ]]
[[ and http://www.linuxppc.org/ for useful information before posting. ]]

#2 lore raw
Quoted 7 lines · roboj

After compiling the recent linux kernel (2.2.9), I've been getting an error message which I have included below. I get it at boot time and it continues printing in an infinite loop. Also, the computer seems to be trying to access my cd-rom drive (Toshiba scsi, /dev/scd0 linked to /dev/cdrom). Running power computing powerbase. Anyone ever got a similar error message that can offer any suggestions? Everything works ok in linux vers. 2.2.6-ac3.

I get something similar on my S900 dual 180Mhz machine with a Matshita CD. It seems more likely to happen when I'm cold booting up my machine, but can also happen after launching from BootX in the Finder. I noticed it after I moved to the 2.2.6 kernels (I'm currently using 2.2.6-15apmac.) Sometimes I have to reboot several times in a row before it gets past the CD which is target 3 on my internal SCSI bus (MESH)

Quoted 8 lines

SCSI: aborting command due to timeout pid 3, scsi 0, channel 0, id 1

mesh_abort (c0374000)
mesh: state at c0374278, regs at f3010000 dma at f3008000
ct = 0, seq = c , bs = 6000, fc = 0, exc = 0, err = 0, im = 7, int = 0, sp = 2, dma stat = c0, cmdptr = 364010, phase = 0, msgphase = 0, comm_tgt = 1, data_ptr = 0, dma_st = 0, dma_ct = 0, n_msgout = 0

Quoted 7 lines

target 1: req = 0374000 goes_out = 0, saved_ptr = 0

SCSI Host 0 abort (pid3) timed out - resetting
SCSI bus is being reset for host 0 channel 0

mesh reset 2
mesh: SCSI bus reset detected: waiting for end...done

Kevin Hendrickson
*--------+---------+---------+---------+---------+---------+---------+-*
Kevin Hendrickson "On the internet, no one knows you're a dog."
[email protected] "Why, oh why, didn't I take the BLUE pill?"
[email protected] _DreaD_ http://net178019.hcv.com/~hndrcksn/

[[ This message was sent via the linuxppc-dev mailing list. Replies are ]] [[ not forced back to the list, so be sure to Cc linuxppc-dev if your ]] [[ reply is of general interest. Please check http://lists.linuxppc.org/ ]]
[[ and http://www.linuxppc.org/ for useful information before posting. ]]

#3 lore raw
Quoted 11 lines · Kevin Hendrickson
Quoted 7 lines · roboj

After compiling the recent linux kernel (2.2.9), I've been getting an error message which I have included below. I get it at boot time and it continues printing in an infinite loop. Also, the computer seems to be trying to access my cd-rom drive (Toshiba scsi, /dev/scd0 linked to /dev/cdrom). Running power computing powerbase. Anyone ever got a similar error message that can offer any suggestions? Everything works ok in linux vers. 2.2.6-ac3.

Quoted 6 lines

I get something similar on my S900 dual 180Mhz machine with a Matshita CD. It seems more likely to happen when I'm cold booting up my machine, but can also happen after launching from BootX in the Finder. I noticed it after I moved to the 2.2.6 kernels (I'm currently using 2.2.6-15apmac.) Sometimes I have to reboot several times in a row before it gets past the CD which is target 3 on my internal SCSI bus (MESH)

I just noticed this morning that I cannot mount anything in this CD drive. I have a CD-R drive at target 5 on my external SCSI bus that can mount CDs fine, but the CD drive mentioned above gives I/O errors and can lock up the machine if I try to mount it or run od on it too many times. I don't know whether this happened with earlier 2.2.x kernels because I haven't had to mount anything in a while. This CD drive mounted fine under the 2.1.x kernels.

Kevin Hendrickson
*--------+---------+---------+---------+---------+---------+---------+-*
Kevin Hendrickson "On the internet, no one knows you're a dog."
[email protected] "Why, oh why, didn't I take the BLUE pill?"
[email protected] _DreaD_ http://net178019.hcv.com/~hndrcksn/

[[ This message was sent via the linuxppc-dev mailing list. Replies are ]] [[ not forced back to the list, so be sure to Cc linuxppc-dev if your ]] [[ reply is of general interest. Please check http://lists.linuxppc.org/ ]]
[[ and http://www.linuxppc.org/ for useful information before posting. ]]