Skip to contentSkip to conversation

Can't get correct VSC8201 PHYID on MPC8347 in uboot-1.1.3 issue

U-Boot-Users Simon Yang 2 participants 4 messages Nov 28, 2005 – Nov 29, 2005

lore
Share & tools
lore

Simon Yang

author
#0 lore raw

Dear All,

Now I use VSC8201PHY on MPC8347 with uboot-1.1.3,I think VSC8201 PHY is similar to CIS8201PHY,so I add struct phy_info_vsc8201 based on struct phy_info_cis8201 in tsec.c and related registers in tsec.h, but during bootup I meet below problem in tsec.c when it goes to read phy_id in function read_phy_reg(), the phy_id is always ffffffff, the log file is as follow:

Net: TSEC initialize begin...
In Read reg func PHY ID is:0
Register number MIIMADD is 2
PHY Reg after read PHYIR1 is:ffff
PHY Reg High 16 bit is:ffff0000
Begin Read phy reg!
In Read reg func PHY ID is:0
Register number MIIMADD is 3
PHY Reg after read PHYIR2 is:ffff
Tsec: read from reg is ffffffff
Freescale TSEC0: PHY id ffffffff is not supported! Freescale TSEC0: No PHY found
TSEC initialize begin...
In Read reg func PHY ID is:1
Register number MIIMADD is 102
PHY Reg after read PHYIR1 is:ffff
PHY Reg High 16 bit is:ffff0000
Begin Read phy reg!
In Read reg func PHY ID is:1
Register number MIIMADD is 103
PHY Reg after read PHYIR2 is:ffff
Tsec: read from reg is ffffffff
Freescale TSEC1: PHY id ffffffff is not supported! Freescale TSEC1: No PHY found
Freescale TSEC0, Freescale TSEC1

Thanks in advance.

Best Regards
SImon

#1 lore raw

Simon

check your config file settings for:

#define TSEC1_PHY_ADDR 0
#define TSEC1_PHYIDX 0
#define TSEC2_PHY_ADDR 1
#define TSEC2_PHYIDX 0

for sanity of MDIO stuff.

Quoted 46 lines

Dear All,

Now I use VSC8201PHY on MPC8347 with uboot-1.1.3,I think VSC8201 PHY is similar to CIS8201PHY,so I add struct phy_info_vsc8201 based on struct phy_info_cis8201 in tsec.c and related registers in tsec.h, but during bootup I meet below problem in tsec.c when it goes to read phy_id in function read_phy_reg(), the phy_id is always ffffffff, the log file is as follow:

Net: TSEC initialize begin...
In Read reg func PHY ID is:0
Register number MIIMADD is 2
PHY Reg after read PHYIR1 is:ffff
PHY Reg High 16 bit is:ffff0000
Begin Read phy reg!
In Read reg func PHY ID is:0
Register number MIIMADD is 3
PHY Reg after read PHYIR2 is:ffff
Tsec: read from reg is ffffffff
Freescale TSEC0: PHY id ffffffff is not supported! Freescale TSEC0: No PHY found
TSEC initialize begin...
In Read reg func PHY ID is:1
Register number MIIMADD is 102
PHY Reg after read PHYIR1 is:ffff
PHY Reg High 16 bit is:ffff0000
Begin Read phy reg!
In Read reg func PHY ID is:1
Register number MIIMADD is 103
PHY Reg after read PHYIR2 is:ffff
Tsec: read from reg is ffffffff
Freescale TSEC1: PHY id ffffffff is not supported! Freescale TSEC1: No PHY found
Freescale TSEC0, Freescale TSEC1

Thanks in advance.

Best Regards
SImon

-------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc. Do you grep through log files for problems? Stop! Download the new AJAX search engine that makes searching your log files as easy as surfing the web. DOWNLOAD SPLUNK!
http://ads.osdn.com/?ad_idv37&alloc_id865&op=click

author
#2 lore raw

Hi David,

I have checked the config file settings, they are correct.

For the MDIO I get nothing on MDIO read frame and write frame of SMI when the uboot is running.What's wrong with it?

2005/11/29, David Updegraff <[email protected]>:

Quoted 70 lines

Simon

check your config file settings for:

#define TSEC1_PHY_ADDR          0
#define TSEC1_PHYIDX            0
#define TSEC2_PHY_ADDR          1
#define TSEC2_PHYIDX            0

for sanity of MDIO stuff.

Quoted 41 lines

Dear All,

Now I use VSC8201PHY on MPC8347 with uboot-1.1.3,I think VSC8201 PHY is similar to CIS8201PHY,so I add struct phy_info_vsc8201 based on struct phy_info_cis8201 in tsec.c and related registers in tsec.h, but during bootup I meet below problem in tsec.c when it goes to read phy_id in function read_phy_reg(), the phy_id is always ffffffff, the log file is as follow:

Net: TSEC initialize begin...
In Read reg func PHY ID is:0
Register number MIIMADD is 2
PHY Reg after read PHYIR1 is:ffff
PHY Reg High 16 bit is:ffff0000
Begin Read phy reg!
In Read reg func PHY ID is:0
Register number MIIMADD is 3
PHY Reg after read PHYIR2 is:ffff
Tsec: read from reg is ffffffff
Freescale TSEC0: PHY id ffffffff is not supported! Freescale TSEC0: No PHY found
TSEC initialize begin...
In Read reg func PHY ID is:1
Register number MIIMADD is 102
PHY Reg after read PHYIR1 is:ffff
PHY Reg High 16 bit is:ffff0000
Begin Read phy reg!
In Read reg func PHY ID is:1
Register number MIIMADD is 103
PHY Reg after read PHYIR2 is:ffff
Tsec: read from reg is ffffffff
Freescale TSEC1: PHY id ffffffff is not supported! Freescale TSEC1: No PHY found
Freescale TSEC0, Freescale TSEC1

Thanks in advance.

Best Regards
SImon

Quoted 5 lines

-------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc. Do you grep through log files for problems? Stop! Download the new AJAX search engine that makes searching your log files as easy as surfing the web. DOWNLOAD SPLUNK!
http://ads.osdn.com/?ad_idv37&alloc_id865&op=click

-------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc. Do you grep through log files for problems? Stop! Download the new AJAX search engine that makes searching your log files as easy as surfing the web. DOWNLOAD SPLUNK!
http://ads.osdn.com/?ad_id=7637&alloc_id=16865&op=click
_______________________________________________
U-Boot-Users mailing list
U-Boot-Users at lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users

author
#3 lore raw

Does anybody use this PHY before and it works well before? Please give me some comment on it, thanks a lot!

2005/11/29, Simon Yang <[email protected]>:

Quoted 81 lines

Hi David,

I have checked the config file settings, they are correct.

For the MDIO I get nothing on MDIO read frame and write frame of SMI when the uboot is running.What's wrong with it?

2005/11/29, David Updegraff <[email protected]>:

Quoted 70 lines

Simon

check your config file settings for:

#define TSEC1_PHY_ADDR          0
#define TSEC1_PHYIDX            0
#define TSEC2_PHY_ADDR          1
#define TSEC2_PHYIDX            0

for sanity of MDIO stuff.

Quoted 41 lines

Dear All,

Now I use VSC8201PHY on MPC8347 with uboot-1.1.3,I think VSC8201 PHY is similar to CIS8201PHY,so I add struct phy_info_vsc8201 based on struct phy_info_cis8201 in tsec.c and related registers in tsec.h, but during bootup I meet below problem in tsec.c when it goes to read phy_id in function read_phy_reg(), the phy_id is always ffffffff, the log file is as follow:

Net: TSEC initialize begin...
In Read reg func PHY ID is:0
Register number MIIMADD is 2
PHY Reg after read PHYIR1 is:ffff
PHY Reg High 16 bit is:ffff0000
Begin Read phy reg!
In Read reg func PHY ID is:0
Register number MIIMADD is 3
PHY Reg after read PHYIR2 is:ffff
Tsec: read from reg is ffffffff
Freescale TSEC0: PHY id ffffffff is not supported! Freescale TSEC0: No PHY found
TSEC initialize begin...
In Read reg func PHY ID is:1
Register number MIIMADD is 102
PHY Reg after read PHYIR1 is:ffff
PHY Reg High 16 bit is:ffff0000
Begin Read phy reg!
In Read reg func PHY ID is:1
Register number MIIMADD is 103
PHY Reg after read PHYIR2 is:ffff
Tsec: read from reg is ffffffff
Freescale TSEC1: PHY id ffffffff is not supported! Freescale TSEC1: No PHY found
Freescale TSEC0, Freescale TSEC1

Thanks in advance.

Best Regards
SImon

Quoted 5 lines

-------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc. Do you grep through log files for problems? Stop! Download the new AJAX search engine that makes searching your log files as easy as surfing the web. DOWNLOAD SPLUNK!
http://ads.osdn.com/?ad_idv37&alloc_id865&op=click

-------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc. Do you grep through log files for problems? Stop! Download the new AJAX search engine that makes searching your log files as easy as surfing the web. DOWNLOAD SPLUNK!
http://ads.osdn.com/?ad_id=7637&alloc_id=16865&op=click
_______________________________________________
U-Boot-Users mailing list
U-Boot-Users at lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users