Problems with multiple harddisks on my Indigo2
Hi all
While trying to build a 2nd harddisk into my Indigo2
I experienced the following problems.
The bus is terminated correctly and with 2 m external
cable to my scsi case it also shouldn't be to long.
When I try to copy data from a harddisk to the other
I get weired I/O erros after some time of heavy I/O.
On the console I get something like:
cp: /mnt/redhat/kernel23/linux/arch/sparc/lib/COPYING.LIB: Input/output error
And dmesg shows:
attempt to access beyond end of device
08:03: rw=0, want=959546428, limit=1888830
attempt to access beyond end of device
08:03: rw=0, want=958585434, limit=1888830
attempt to access beyond end of device
08:03: rw=0, want=959546428, limit=1888830
attempt to access beyond end of device
08:03: rw=0, want=958585434, limit=1888830
attempt to access beyond end of device
08:03: rw=0, want=941858675, limit=1888830
Ususally the system is pretty unstable after these messages.
Also I'm getting a message
sc1,2,0: cmd=0x12 timeout after 2 sec. Resetting SCSI bus every time I restart my Indigo2 on the serial console - does anyone know what that means and if it's a problem ?
Further more it happens that after heavy I/O a simple "sync" needs more than one minute.
Has anyone seen the same or equal problems in any way and/ was able to resolve these ?
TIA, Klaus
Signature · 4 lines
Full Name : Klaus Naumann | (http://www.mgnet.de/) (Germany) Nickname : Spock | Org.: Mad Guys Network Phone / FAX : ++49/177/7862964 | E-Mail: ([email protected]) PGP Key : www.mgnet.de/keys/key_spock.txt
Hello,
Quoted 5 lines
cp:
/mnt/redhat/kernel23/linux/arch/sparc/lib/COPYING.LIB:
Input/output error
And dmesg shows:
attempt to access beyond end of device
08:03: rw=0, want=959546428, limit=1888830
[SNIP]
I have an SGI Indy, with 2 internal hard disks, a 4GB and a 1GB
I get the same thing!
Quoted 2 lines
Also I'm getting a message
sc1,2,0: cmd=0x12 timeout after 2 sec. Resetting SCSI bus
I started getting this when I added the 2nd HD (1GB).
Bye for Now,
Ian
\|||/
(o o)
/----------------ooO-(_)-Ooo----------------\
| Ian Chilton |
| E-Mail : [email protected] |
| IRC Nick: GadgetMan |\-------------------------------------------/
Quoted 10 lines · Ian Chilton
I have an SGI Indy, with 2 internal hard disks, a 4GB and a 1GB
I get the same thing!
Quoted 2 lines
Also I'm getting a message
sc1,2,0: cmd=0x12 timeout after 2 sec. Resetting SCSI busI started getting this when I added the 2nd HD (1GB).
fwiw, i got this too on my indy when i added a Quantum Empire 1GB.
From cold boot the PROM doesn't recognise the second disk, but IRIX does (PROM gives me the exact same error message as the one you wrote above - but prints it twice). If i halt back to PROM then the PROM does see the second disk. (and only prints that error message once)
my theories are:
1. PROM controller driver is minimal and doesn't init the controller/disks properly whereas the IRIX driver does.
2. disk spin up times.. ??
3. Perhaps cause the outboard SCSI port is not terminated. (least not on my indy)
Quoted 1 line
Signature · 7 lines
Paul Jakma [email protected] PGP5 key: http://www.clubi.ie/jakma/publickey.txt ------------------------------------------- Fortune: Give me a fish and I will eat today. Teach me to fish and I will eat forever.
All,
Try looking up the jumper'ing information for the drive... There is probably a delay for spinning the drive up at boot (or some such nonsense).
Regards,
Ken
Quoted 41 lines · Paul Jakma
Subject: RE: Problems with multiple harddisks on my Indigo2
Quoted 10 lines · Ian Chilton
I have an SGI Indy, with 2 internal hard disks, a 4GB and a 1GB
I get the same thing!
Quoted 2 lines
Also I'm getting a message
sc1,2,0: cmd=0x12 timeout after 2 sec. Resetting SCSI busI started getting this when I added the 2nd HD (1GB).
fwiw, i got this too on my indy when i added a Quantum Empire 1GB.
Quoted 1 line
From cold boot the PROM doesn't recognise the second disk, but IRIX
does (PROM gives me the exact same error message as the one you wrote above - but prints it twice). If i halt back to PROM then the PROM does see the second disk. (and only prints that error message once)
my theories are:
1. PROM controller driver is minimal and doesn't init the controller/disks properly whereas the IRIX driver does.
2. disk spin up times.. ??
3. Perhaps cause the outboard SCSI port is not terminated. (least not on my indy)
Quoted 1 line
--
Paul Jakma [email protected]
PGP5 key: http://www.clubi.ie/jakma/publickey.txt
-------------------------------------------
Fortune:
Give me a fish and I will eat today.Teach me to fish and I will eat forever.
-- End of excerpt from Paul Jakma
Quoted 6 lines · J.K. Hill
All,
Try looking up the jumper'ing information for the drive... There is probably a delay for spinning the drive up at boot (or some such nonsense).
checked that.. and it's not it. the jumper isn't set. (i think).
however, this drive used to be in an Alpha, and ARCSBIOS on Alpha had a problem with not recognising it from cold too, sometimes.
so maybe the drive just doesn't spin up fast enough.
Quoted 3 lines
Regards,
Ken
thanks,
Signature · 7 lines
Paul Jakma [email protected] PGP5 key: http://www.clubi.ie/jakma/publickey.txt ------------------------------------------- Fortune: The price one pays for pursuing any profession, or calling, is an intimate knowledge of its ugly side. -- James Baldwin
Quoted 7 lines · Paul Jakma
Subject: RE: Problems with multiple harddisks on my Indigo2 On Wed, 21 Jun 2000, Ian Chilton wrote:
3. Perhaps cause the outboard SCSI port is not terminated. (least not on my indy)
The SCSI port should be terminated with an active terminator on the Indy, regardless of if you have 1 or 2 drives installed.
-Roald
Signature · 15 lines
--------------------------------------------------------------- | Company: SGI Norge A/S | | Email: [email protected] Tlf: +47 5163 4183 | | Addr: Luramyrveien 79 Mobil: +47 909 33 903| | N-4313 Sandnes VMail (SGI): 870-4679 | | NORWAY VMail(ext): +47 6711 4679 | --------------------------------------------------------------- Essential SGI Websites: http://www.sgi.com/ SGI http://www.sgi.no/ SGI Norge http://support-europe.sgi.com/ Log calls, patches+overlays, ++ http://freeware.sgi.com/ Freeware - "ready-to-eat" http://oss.sgi.com/mips/ Linux for SGI (Mips/Intel) http://www.sgi.com/developers/ Developer Central http://www.sgi.com/Products/Evaluation/ Evaluation Software
Hello,
Just to let you guys know...
I just tried the 2x HD thing in IRIX (on my Indy), and no problems! So, it IS a Linux/MIPS problem!!
I did: cp -R /usr /hd2
It was going for about 10 mins, before it ran out of disk space (1GB !). No
errors at all :)
Bye for Now,
Ian
\|||/
(o o)
/----------------ooO-(_)-Ooo----------------\
| Ian Chilton |
| IRC Nick: GadgetMan |
| E-Mail : [email protected] |\-------------------------------------------/
Good Morning,
The SCSI reset problem occurred on my Indy after I added a Floptical on ID 2. I am not running Linux on the box at this time. Have upgraded to 6.2 from 5.3 but haven't tried to reinstall the floptical yet. Set jumpers to Indy specs, so am unsure why. BTW, would the Indy boot from the floptical for Linux without doing a net boot?
Sincerely,
Dave Keen
Quoted 24 lines · Ian Chilton
Hello,
Just to let you guys know...
I just tried the 2x HD thing in IRIX (on my Indy), and no problems! So, it IS a Linux/MIPS problem!!
I did: cp -R /usr /hd2
It was going for about 10 mins, before it ran out of disk space (1GB !). No
errors at all :)Bye for Now,
Ian
\|||/ (o o) /----------------ooO-(_)-Ooo----------------\ | Ian Chilton | | IRC Nick: GadgetMan | | E-Mail : [email protected] |\-------------------------------------------/
Quoted 2 lines · On Fri, 23 Jun 2000 16:25:42 David Keen wrote:
jumpers to Indy specs, so am unsure why. BTW, would the Indy boot from the floptical for Linux without doing a net boot?
I've heard from someone that it is possible - but I'm not sure - try it ;)
CU, Klaus
Signature · 4 lines
Full Name : Klaus Naumann | (http://www.mgnet.de/) (Germany) Nickname : Spock | Org.: Mad Guys Network Phone / FAX : ++49/177/7862964 | E-Mail: ([email protected]) PGP Key : www.mgnet.de/keys/key_spock.txt