setting the frequency on an airport card?
All
does anyone know how to go about setting the frequency on the airport card? The only way I can think of that seems to want to work is using iwconfig (see http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/) but all it keeps saying is
[20:48:11] 17 shiva root ~>iwconfig airport freq 2.442GHz
SIOCSIWFREQ: Operation not supported
it says that (same response, different ioctl) for all the ioctl's except the one to set the essid.
I dont understand why it is not setting the frequency or not able to. (I need to do this so I can actually speak to another 802.11b card, one which I also cant set the frequency on with iwconfig and have not the faintest as to why it is failing either).
The airport.c (benh's I had to pull out some code and change one line so it would actually compile unfortunately, mostly it seemed to be things messing up with version differences (running this with 2.4.0), see diff -u below) contains the ioctl sections for setting the frequency and all the others as far as I can tell.
The aiport.c contains
if ((port_type != 3) || (wrq->u.freq.m > 1000) || (wrq->u.freq.e > 0))
rc = -EOPNOTSUPP;
which is I guess where it is failing, anyone know why the airport card doesnt seem to want to have it's frequency changed? (or for that matter the majority of the ioctls the wireless extensions allow use of?
See You
Steve
--
[email protected] http://wibble.net/~sjh/
Look Up In The Sky
Is it a bird? No
Is it a plane? No
Is it a small blue banana?
YES
this diff was the quick changes I needed to get the module ben has on his website to compile and insert successfully
on insertion I get the message
[20:47:10] 11 shiva root ~>insmod airport.o airport.o parameter enc has unknown format modifier '*'
however all seems fine
Jan 15 20:18:46 shiva kernel: airport: Airport WaveLAN/IEEE driver v1.0.4 Jan 15 20:18:46 shiva kernel: airport: (c) Benjamin Herrenschmidt <[email protected]> Jan 15 20:18:46 shiva kernel: airport: (c) Andreas Neuhaus <[email protected]> Jan 15 20:18:47 shiva kernel: airport: Registered netdevice airport Jan 15 20:18:47 shiva kernel: airport: MAC address on airport is 00 30 65 12
22 99
so hey
airport.c Mon Jan 15 20:46:24 2001 renamed from airport.c Mon Jan 15 21:22:13 2001 +0 -2
@@ -2170,24 +2170,7 @@ DEBUG(DEBUG_CALLTRACE, "-> airport_tx(%s)\n", dev->name); -#if (KERNEL_VERSION_CODE < KERNEL_VERSION(2,3,42)) - // We normally shouldn't be called if queue is stopped (transmitter
busy)
- // but older kernel code does anyway. So we'll check if the last
- // transmission has timed out and reset the device in case
- if (test_and_set_bit(0, (void *) &dev->tbusy) != 0) {- DEBUG(DEBUG_TXRX, "%s: airport_tx(%s) called while busy!\n",dev_info, dev->name);
- if ((jiffies - dev->trans_start) < TX_TIMEOUT)
- return 1;
- if (!netif_running(dev))
- {
- printk(KERN_WARNING "%s: %s Tx on stopped
device!\n", dev_info, dev->name);
- return 1;
- }
- airport_watchdog(dev);
- }
-#else
netif_stop_queue(dev);
-#endif
skb_tx_check(dev, skb);
@@ -2657,7 +2640,7 @@
// Other netdevice data
if (!eth)
- dev->name = "airport";
+ strncpy (dev->name, "airport", 8);
dev->mtu = mtu; // netif_stop_queue(dev);
k_compat.h Mon Jan 15 20:40:50 2001 renamed from k_compat.h Mon Jan 15 21:22:56 2001 +4 -0
@@ -119,11 +119,13 @@ #define signal_pending(cur) ((cur)->signal & ~(cur)->blocked) #endif +/* #if (LINUX_VERSION_CODE < VERSION(2,1,86)) #define DEV_KFREE_SKB(skb) dev_kfree_skb(skb, FREE_WRITE) #else #define DEV_KFREE_SKB(skb) dev_kfree_skb(skb) #endif +*/ #if (LINUX_VERSION_CODE < VERSION(2,1,89)) #define POLL_WAIT(f, q, w) poll_wait(q, w)
@@ -285,6 +287,7 @@ resetup_one_dev(dev, drive); } while (0); #endif +/* #if (LINUX_VERSION_CODE < VERSION(2,1,25)) #define net_device_stats enet_statistics #define skb_tx_check(dev, skb) \
@@ -297,6 +300,7 @@ #define add_rx_bytes(stats, n) do { (stats)->rx_bytes += n; } while (0) #define add_tx_bytes(stats, n) do { (stats)->tx_bytes += n; } while (0) #endif +*/ #if (LINUX_VERSION_CODE < VERSION(2,3,43)) #define netif_stop_queue(dev) set_bit(0, (void *)&(dev)->tbusy)
** Sent via the linuxppc-dev mail list. See http://lists.linuxppc.org/
Quoted 4 lines · Steven Hanley
The
aiport.ccontains
if ((port_type!= 3) || (wrq->u.freq.m> 1000) || (wrq->u.freq.e> 0))
rc =-EOPNOTSUPP;
I must be in stupid mode today or something, I looked at this for a minute or two and suddenly wondered, what hte heck is that port_type thing, of course a quick glance at the top of the file shows it is a module paramater, so when I set it on modporbe or insmode on both machines suddenly I can use the ioctls, duh, anyway I will probably put this up on a web page or some such in the next day or so (my how to get this running page) as it was not exactly obvious to me and I didnt see mention of the port type paramater (I suppose airports and their clients are usually managed)
Anyway happy now :)
See You
Steve
--
[email protected] http://wibble.net/~sjh/
Look Up In The Sky
Is it a bird? No
Is it a plane? No
Is it a small blue banana?
YES
** Sent via the linuxppc-dev mail list. See http://lists.linuxppc.org/