VT82C597 + Maxtor UDMA failures
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hey Vojtech,
Thanks for your response. I tried using 2.4.2-pre3 and the same problem occurs, in exactly the same manner. The only other problem I can identify is a boot message:
IRQ routing conflict in pirq table for device 00:0a.0
lspci reveals that 00:0a.0 is my network card:
00:0a.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone]
But I'm not sure why that would have any problem, as it works perfectly, and I don't see any conflicts:
/proc/interrupts:
CPU0
0: 416389 XT-PIC timer 1: 18840 XT-PIC keyboard 2: 0 XT-PIC cascade 8: 1 XT-PIC rtc 9: 135491 XT-PIC soundblaster 10: 83005 XT-PIC eth0 11: 386543 XT-PIC nvidia 12: 121397 XT-PIC PS/2 Mouse 14: 3967 XT-PIC ide0 15: 249701 XT-PIC ide1 NMI: 0 ERR: 0
If you would like any other info, or have any ideas, please let me know. The cable seems to be fine, and like I said it works okay in Windows.
Thanks again,
Ryan
Quoted 781 lines · Vojtech Pavlik
Hi!
Please try 2.4.2-pre kernels, they have a newer VIA IDE driver.
Vojtech
Quoted 771 lines · Ryan Hayle
I'm trying to troubleshoot a failure with my Maxtor hard drive that I have experienced consistantly, even in the 2.2.x kernels (I'm now running 2.2.1-test10, .config is attached). It detects all of my drives fine:
block: queued sectors max/low 126786kB/95090kB, 384 slots per queue Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xxVP_IDE: IDE controller on PCI bus 00 dev 39VP_IDE: chipset revision 6VP_IDE: not 100% native mode: will probe irqs laterVP_IDE: VIA vt82c586b IDE UDMA33 controller on pci0:7.1ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMAhda: Maxtor 52049U4, ATA DISK drive
hdb: WDC AC31200F, ATA DISK drive
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hdc: Maxtor 90680D4, ATA DISK drive
hdd: ATAPI 40X CDROM DRIVE, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 40020624 sectors (20491 MB) w/2048KiB Cache, CHS=2491/255/63, UDMA(33)
hdb: 2503872 sectors (1282 MB) w/64KiB Cache, CHS=621/64/63, DMA
hdc: 13281408 sectors (6800 MB) w/256KiB Cache, CHS=13176/16/63, UDMA(33)
hdd: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33)And then all the services load up, etc. Once I log in, though, either in gdm or on the console, it will pause for around 10-15 seconds, and then display this:
hdc: timeout waiting for DMA
ide_dmaproc: chipset supportedide_dma_timeoutfunc only: 14
hdc: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hdc: status timeout: status=0xd0 { Busy }
hdc: DMA disabled
hdd: DMA disabled
hdc: drive not ready for command
ide1: reset: success(hdc is the problem, obviously) Once this occurs, the system appears to run normally. I don't really care about hdd (cdrom), although I figure they are probably related somehow.
Windows is able to use UDMA fine on this drive. Also note that this isn't a UDMA66 drive, and I'm not trying to use it (most of the other posts I've seen with similar problems were related to 66).
Drives on ide0 seem to run in udma mode just fine, also...
Here's
/proc/ide/via:----------VIA BusMastering IDE Configuration----------------
Driver Version: 2.1e South Bridge: VIA vt82c586b rev 0x47 Command register: 0x7 Latency timer: 64 PCI clock: 33MHz Master Read Cycle IRDY: 1ws Master Write Cycle IRDY: 1wsFIFO Output Data 1/2 Clock Advance: off
BM IDE Status Register Read Retry: on
Max DRDY Pulse Width: No limit
-----------------------Primary IDE-------Secondary IDE------Read DMA FIFO flush: on on End Sect. FIFO flush: on on Prefetch Buffer: on on Post Write Buffer: on on FIFO size: 8 8 Threshold Prim.: 1/2 1/2 Bytes Per Sector: 512 512 Both channels togth: yes yes -------------------drive0----drive1----drive2----drive3----- BMDMA enabled: yes yes no no Transfer Mode: UDMA DMA/PIO UDMA UDMA Address Setup: 30ns 60ns 30ns 30ns Active Pulse: 90ns 90ns 90ns 90ns Recovery Time: 30ns 60ns 30ns 30ns Cycle Time: 60ns 150ns 60ns 60ns Transfer Rate: 33.0MB/s 13.2MB/s 33.0MB/s 33.0MB/sWhat I don't understand is, the transfer mode still seems to be "UDMA", but "BMDMA" is not enabled. Aren't they inter-dependant? One in the same? I'm obviously no expert, so any help would be appreciated.
Thanks in advance,
Ryan#
# Automatically generated make config: don't edit
#CONFIG_X86=yCONFIG_ISA=y
#CONFIG_SBUSis not setCONFIG_UID16=y#
# Code maturity level options
#CONFIG_EXPERIMENTAL=y#
# Loadable module support
#CONFIG_MODULES=yCONFIG_MODVERSIONS=yCONFIG_KMOD=y#
# Processor type and features
#
#CONFIG_M386is not set
#CONFIG_M486is not set
#CONFIG_M586is not set
#CONFIG_M586TSCis not set
#CONFIG_M586MMXis not set
#CONFIG_M686is not set
#CONFIG_MPENTIUMIIIis not set
#CONFIG_MPENTIUM4is not setCONFIG_MK6=y
#CONFIG_MK7is not set
#CONFIG_MCRUSOEis not set
#CONFIG_MWINCHIPC6is not set
#CONFIG_MWINCHIP2is not set
#CONFIG_MWINCHIP3Dis not setCONFIG_X86_WP_WORKS_OK=yCONFIG_X86_INVLPG=yCONFIG_X86_CMPXCHG=yCONFIG_X86_BSWAP=yCONFIG_X86_POPAD_OK=yCONFIG_X86_L1_CACHE_SHIFT=5CONFIG_X86_ALIGNMENT_16=yCONFIG_X86_TSC=yCONFIG_X86_USE_PPRO_CHECKSUM=y
#CONFIG_TOSHIBAis not set
#CONFIG_MICROCODEis not set
#CONFIG_X86_MSRis not set
#CONFIG_X86_CPUIDis not setCONFIG_NOHIGHMEM=y
#CONFIG_HIGHMEM4Gis not set
#CONFIG_HIGHMEM64Gis not set
#CONFIG_MATH_EMULATIONis not setCONFIG_MTRR=y
#CONFIG_SMPis not set
#CONFIG_X86_UP_IOAPICis not set#
# General setup
#CONFIG_NET=y
#CONFIG_VISWSis not setCONFIG_PCI=y
#CONFIG_PCI_GOBIOSis not set
#CONFIG_PCI_GODIRECTis not setCONFIG_PCI_GOANY=yCONFIG_PCI_BIOS=yCONFIG_PCI_DIRECT=yCONFIG_PCI_NAMES=y
#CONFIG_EISAis not set
#CONFIG_MCAis not set
#CONFIG_HOTPLUGis not set
#CONFIG_PCMCIAis not setCONFIG_SYSVIPC=y
#CONFIG_BSD_PROCESS_ACCTis not setCONFIG_SYSCTL=yCONFIG_KCORE_ELF=y
#CONFIG_KCORE_AOUTis not setCONFIG_BINFMT_AOUT=mCONFIG_BINFMT_ELF=yCONFIG_BINFMT_MISC=mCONFIG_PM=y
#CONFIG_ACPIis not set
#CONFIG_APMis not set#
# Memory Technology Devices (MTD)
#
#CONFIG_MTDis not set#
# Parallel port support
#CONFIG_PARPORT=mCONFIG_PARPORT_PC=m
#CONFIG_PARPORT_PC_FIFOis not set
#CONFIG_PARPORT_PC_SUPERIOis not set
#CONFIG_PARPORT_AMIGAis not set
#CONFIG_PARPORT_MFC3is not set
#CONFIG_PARPORT_ATARIis not set
#CONFIG_PARPORT_SUNBPPis not set
#CONFIG_PARPORT_OTHERis not setCONFIG_PARPORT_1284=y#
# Plug and Play configuration
#CONFIG_PNP=yCONFIG_ISAPNP=y#
# Block devices
#CONFIG_BLK_DEV_FD=y
#CONFIG_BLK_DEV_XDis not set
#CONFIG_PARIDEis not set
#CONFIG_BLK_CPQ_DAis not set
#CONFIG_BLK_CPQ_CISS_DAis not set
#CONFIG_BLK_DEV_DAC960is not setCONFIG_BLK_DEV_LOOP=m
#CONFIG_BLK_DEV_NBDis not set
#CONFIG_BLK_DEV_RAMis not set#
# Multi-device support (RAID and LVM)
#
#CONFIG_MDis not set#
# Networking options
#CONFIG_PACKET=y
#CONFIG_PACKET_MMAPis not set
#CONFIG_NETLINKis not set
#CONFIG_NETFILTERis not set
#CONFIG_FILTERis not setCONFIG_UNIX=yCONFIG_INET=yCONFIG_IP_MULTICAST=y
#CONFIG_IP_ADVANCED_ROUTERis not set
#CONFIG_IP_PNPis not set
#CONFIG_NET_IPIPis not set
#CONFIG_NET_IPGREis not set
#CONFIG_IP_MROUTEis not set
#CONFIG_INET_ECNis not set
#CONFIG_SYN_COOKIESis not set
#CONFIG_IPV6is not setCONFIG_KHTTPD=m
#CONFIG_ATMis not set#
#
#
#CONFIG_IPXis not set
#CONFIG_ATALKis not set
#CONFIG_DECNETis not set
#CONFIG_BRIDGEis not set
#CONFIG_X25is not set
#CONFIG_LAPBis not set
#CONFIG_LLCis not set
#CONFIG_NET_DIVERTis not set
#CONFIG_ECONETis not set
#CONFIG_WAN_ROUTERis not set
#CONFIG_NET_FASTROUTEis not set
#CONFIG_NET_HW_FLOWCONTROLis not set#
# QoS and/or fair queueing
#
#CONFIG_NET_SCHEDis not set#
# Telephony Support
#
#CONFIG_PHONEis not set#
# ATA/IDE/MFM/RLL support
#CONFIG_IDE=y#
# IDE, ATA and ATAPI Block devices
#CONFIG_BLK_DEV_IDE=y#
# Please seeDocumentation/ide.txtfor help/info on IDE drives #
#CONFIG_BLK_DEV_HD_IDEis not set
#CONFIG_BLK_DEV_HDis not setCONFIG_BLK_DEV_IDEDISK=yCONFIG_IDEDISK_MULTI_MODE=y
#CONFIG_BLK_DEV_IDEDISK_VENDORis not set
#CONFIG_BLK_DEV_COMMERIALis not setCONFIG_BLK_DEV_IDECD=y
#CONFIG_BLK_DEV_IDETAPEis not set
#CONFIG_BLK_DEV_IDEFLOPPYis not set#
# IDE chipset support/bugfixes
#
#CONFIG_BLK_DEV_CMD640is not set
#CONFIG_BLK_DEV_ISAPNPis not set
#CONFIG_BLK_DEV_RZ1000is not setCONFIG_BLK_DEV_IDEPCI=y
#CONFIG_IDEPCI_SHARE_IRQis not setCONFIG_BLK_DEV_IDEDMA_PCI=y
#CONFIG_BLK_DEV_OFFBOARDis not setCONFIG_IDEDMA_PCI_AUTO=yCONFIG_BLK_DEV_IDEDMA=y
#CONFIG_IDEDMA_PCI_WIPis not set
#CONFIG_BLK_DEV_AEC62XXis not set
#CONFIG_BLK_DEV_ALI15X3is not set
#CONFIG_BLK_DEV_AMD7409is not set
#CONFIG_BLK_DEV_CMD64Xis not set
#CONFIG_BLK_DEV_CY82C693is not set
#CONFIG_BLK_DEV_CS5530is not set
#CONFIG_BLK_DEV_HPT34Xis not set
#CONFIG_BLK_DEV_HPT366is not set
#CONFIG_BLK_DEV_PIIXis not set
#CONFIG_BLK_DEV_NS87415is not set
#CONFIG_BLK_DEV_OPTI621is not set
#CONFIG_BLK_DEV_PDC202XXis not set
#CONFIG_BLK_DEV_OSB4is not set
#CONFIG_BLK_DEV_SIS5513is not set
#CONFIG_BLK_DEV_SLC90E66is not set
#CONFIG_BLK_DEV_TRM290is not setCONFIG_BLK_DEV_VIA82CXXX=y
#CONFIG_IDE_CHIPSETSis not setCONFIG_IDEDMA_AUTO=y
#CONFIG_IDEDMA_IVBis not set
#CONFIG_DMA_NONPCIis not setCONFIG_BLK_DEV_IDE_MODES=y#
# SCSI support
#
#CONFIG_SCSIis not set#
# IEEE 1394 (FireWire) support
#
#CONFIG_IEEE1394is not set#
# I2O device support
#
#CONFIG_I2Ois not set#
# Network device support
#CONFIG_NETDEVICES=y#
# ARCnet devices
#
#CONFIG_ARCNETis not setCONFIG_DUMMY=m
#CONFIG_BONDINGis not set
#CONFIG_EQUALIZERis not set
#CONFIG_TUNis not set
#CONFIG_NET_SB1000is not set#
# Ethernet (10 or 100Mbit)
#CONFIG_NET_ETHERNET=yCONFIG_NET_VENDOR_3COM=y
#CONFIG_EL1is not set
#CONFIG_EL2is not set
#CONFIG_ELPLUSis not set
#CONFIG_EL16is not set
#CONFIG_EL3is not set
#CONFIG_3C515is not setCONFIG_VORTEX=y
#CONFIG_LANCEis not set
#CONFIG_NET_VENDOR_SMCis not set
#CONFIG_NET_VENDOR_RACALis not set
#CONFIG_AT1700is not set
#CONFIG_DEPCAis not set
#CONFIG_HP100is not set
#CONFIG_NET_ISAis not set
#CONFIG_NET_PCIis not set
#CONFIG_NET_POCKETis not set#
# Ethernet (1000 Mbit)
#
#CONFIG_ACENICis not set
#CONFIG_HAMACHIis not set
#CONFIG_YELLOWFINis not set
#CONFIG_SK98LINis not set
#CONFIG_FDDIis not set
#CONFIG_HIPPIis not set
#CONFIG_PLIPis not setCONFIG_PPP=m
#CONFIG_PPP_MULTILINKis not set
#CONFIG_PPP_ASYNCis not set
#CONFIG_PPP_SYNC_TTYis not setCONFIG_PPP_DEFLATE=mCONFIG_PPP_BSDCOMP=m
#CONFIG_PPPOEis not set
#CONFIG_SLIPis not set#
# Wireless LAN (non-hamradio)
#
#CONFIG_NET_RADIOis not set#
# Token Ring devices
#
#CONFIG_TRis not set
#CONFIG_NET_FCis not set
#CONFIG_RCPCIis not set
#CONFIG_SHAPERis not set#
# Wan interfaces
#
#CONFIG_WANis not set#
# Amateur Radio support
#
#CONFIG_HAMRADIOis not set#
# IrDA (infrared) support
#
#CONFIG_IRDAis not set#
# ISDN subsystem
#
#CONFIG_ISDNis not set#
# Old CD-ROM drivers (not SCSI, not IDE)
#
#CONFIG_CD_NO_IDESCSIis not set#
# Input core support
#CONFIG_INPUT=m
#CONFIG_INPUT_KEYBDEVis not set
#CONFIG_INPUT_MOUSEDEVis not set
#CONFIG_INPUT_JOYDEVis not set
#CONFIG_INPUT_EVDEVis not set#
# Character devices
#CONFIG_VT=yCONFIG_VT_CONSOLE=yCONFIG_SERIAL=y
#CONFIG_SERIAL_CONSOLEis not set
#CONFIG_SERIAL_EXTENDEDis not set
#CONFIG_SERIAL_NONSTANDARDis not setCONFIG_UNIX98_PTYS=yCONFIG_UNIX98_PTY_COUNT=512CONFIG_PRINTER=m
#CONFIG_LP_CONSOLEis not set
#CONFIG_PPDEVis not set#
# I2C support
#CONFIG_I2C=mCONFIG_I2C_ALGOBIT=m
#CONFIG_I2C_PHILIPSPARis not set
#CONFIG_I2C_ELVis not set
#CONFIG_I2C_VELLEMANis not set
#CONFIG_I2C_ALGOPCFis not set
#CONFIG_I2C_CHARDEVis not set#
# Mice
#
#CONFIG_BUSMOUSEis not setCONFIG_MOUSE=yCONFIG_PSMOUSE=y
#CONFIG_82C710_MOUSEis not set
#CONFIG_PC110_PADis not set#
# Joysticks
#CONFIG_JOYSTICK=y#
# Game port support
#
#CONFIG_INPUT_NS558is not set
#CONFIG_INPUT_LIGHTNINGis not set
#CONFIG_INPUT_PCIGAMEis not set#
# Gameport joysticks
#CONFIG_INPUT_ANALOG=m
#CONFIG_INPUT_A3Dis not set
#CONFIG_INPUT_ADIis not set
#CONFIG_INPUT_COBRAis not set
#CONFIG_INPUT_GF2Kis not set
#CONFIG_INPUT_GRIPis not set
#CONFIG_INPUT_INTERACTis not set
#CONFIG_INPUT_TMDCis not set
#CONFIG_INPUT_SIDEWINDERis not set#
# Serial port support
#
#CONFIG_INPUT_SERPORTis not set#
# Serial port joysticks
#
#CONFIG_INPUT_WARRIORis not set
#CONFIG_INPUT_MAGELLANis not set
#CONFIG_INPUT_SPACEORBis not set
#CONFIG_INPUT_SPACEBALLis not set
#CONFIG_INPUT_IFORCE_232is not set#
# Parallel port joysticks
#
#CONFIG_INPUT_DB9is not set
#CONFIG_INPUT_GAMECONis not set
#CONFIG_INPUT_TURBOGRAFXis not set
#CONFIG_QIC02_TAPEis not set#
# Watchdog Cards
#
#CONFIG_WATCHDOGis not set
#CONFIG_INTEL_RNGis not set
#CONFIG_NVRAMis not setCONFIG_RTC=m
#CONFIG_DTLKis not set
#CONFIG_R3964is not set
#CONFIG_APPLICOMis not set#
# Ftape, the floppy tape device driver
#
#CONFIG_FTAPEis not set
#CONFIG_AGPis not set
#CONFIG_DRMis not set#
# Multimedia devices
#CONFIG_VIDEO_DEV=m#
# Video For Linux
#CONFIG_VIDEO_PROC_FS=y
#CONFIG_I2C_PARPORTis not set#
# Video Adapters
#CONFIG_VIDEO_BT848=m
#CONFIG_VIDEO_PMSis not set
#CONFIG_VIDEO_BWQCAMis not set
#CONFIG_VIDEO_CQCAMis not set
#CONFIG_VIDEO_CPIAis not set
#CONFIG_VIDEO_SAA5249is not set
#CONFIG_TUNER_3036is not set
#CONFIG_VIDEO_STRADISis not set
#CONFIG_VIDEO_ZORANis not set
#CONFIG_VIDEO_ZR36120is not set#
# Radio Adapters
#
#CONFIG_RADIO_CADETis not set
#CONFIG_RADIO_RTRACKis not set
#CONFIG_RADIO_RTRACK2is not set
#CONFIG_RADIO_AZTECHis not set
#CONFIG_RADIO_GEMTEKis not set
#CONFIG_RADIO_MAESTROis not set
#CONFIG_RADIO_MIROPCM20is not set
#CONFIG_RADIO_SF16FMIis not set
#CONFIG_RADIO_TERRATECis not set
#CONFIG_RADIO_TRUSTis not set
#CONFIG_RADIO_TYPHOONis not set
#CONFIG_RADIO_ZOLTRIXis not set#
# File systems
#
#CONFIG_QUOTAis not set
#CONFIG_AUTOFS_FSis not setCONFIG_AUTOFS4_FS=y
#CONFIG_REISERFS_FSis not set
#CONFIG_ADFS_FSis not set
#CONFIG_AFFS_FSis not set
#CONFIG_HFS_FSis not set
#CONFIG_BFS_FSis not setCONFIG_FAT_FS=y
#CONFIG_MSDOS_FSis not setCONFIG_VFAT_FS=y
#CONFIG_EFS_FSis not setCONFIG_JFFS_FS_VERBOSE=0
#CONFIG_CRAMFSis not set
#CONFIG_RAMFSis not setCONFIG_ISO9660_FS=mCONFIG_JOLIET=y
#CONFIG_MINIX_FSis not set
#CONFIG_NTFS_FSis not set
#CONFIG_HPFS_FSis not setCONFIG_PROC_FS=y
#CONFIG_DEVFS_FSis not setCONFIG_DEVPTS_FS=y
#CONFIG_QNX4FS_FSis not set
#CONFIG_ROMFS_FSis not setCONFIG_EXT2_FS=y
#CONFIG_SYSV_FSis not set
#CONFIG_UDF_FSis not set
#CONFIG_UFS_FSis not set#
# Network File Systems
#
#CONFIG_CODA_FSis not set
#CONFIG_NFS_FSis not set
#CONFIG_NFSDis not set
#CONFIG_SUNRPCis not set
#CONFIG_LOCKDis not setCONFIG_SMB_FS=mCONFIG_SMB_NLS_DEFAULT=yCONFIG_SMB_NLS_REMOTE="cp437"
#CONFIG_NCP_FSis not set#
# Partition Types
#
#CONFIG_PARTITION_ADVANCEDis not setCONFIG_MSDOS_PARTITION=yCONFIG_SMB_NLS=yCONFIG_NLS=y#
# Native Language Support
#CONFIG_NLS_DEFAULT="iso8859-1"CONFIG_NLS_CODEPAGE_437=m
#CONFIG_NLS_CODEPAGE_737is not set
#CONFIG_NLS_CODEPAGE_775is not set
#CONFIG_NLS_CODEPAGE_850is not set
#CONFIG_NLS_CODEPAGE_852is not set
#CONFIG_NLS_CODEPAGE_855is not set
#CONFIG_NLS_CODEPAGE_857is not set
#CONFIG_NLS_CODEPAGE_860is not set
#CONFIG_NLS_CODEPAGE_861is not set
#CONFIG_NLS_CODEPAGE_862is not set
#CONFIG_NLS_CODEPAGE_863is not set
#CONFIG_NLS_CODEPAGE_864is not set
#CONFIG_NLS_CODEPAGE_865is not set
#CONFIG_NLS_CODEPAGE_866is not set
#CONFIG_NLS_CODEPAGE_869is not set
#CONFIG_NLS_CODEPAGE_874is not set
#CONFIG_NLS_CODEPAGE_932is not set
#CONFIG_NLS_CODEPAGE_936is not set
#CONFIG_NLS_CODEPAGE_949is not set
#CONFIG_NLS_CODEPAGE_950is not setCONFIG_NLS_ISO8859_1=y
#CONFIG_NLS_ISO8859_2is not set
#CONFIG_NLS_ISO8859_3is not set
#CONFIG_NLS_ISO8859_4is not set
#CONFIG_NLS_ISO8859_5is not set
#CONFIG_NLS_ISO8859_6is not set
#CONFIG_NLS_ISO8859_7is not set
#CONFIG_NLS_ISO8859_8is not set
#CONFIG_NLS_ISO8859_9is not set
#CONFIG_NLS_ISO8859_14is not set
#CONFIG_NLS_ISO8859_15is not set
#CONFIG_NLS_KOI8_Ris not set
#CONFIG_NLS_UTF8is not set#
# Console drivers
#CONFIG_VGA_CONSOLE=yCONFIG_VIDEO_SELECT=y
#CONFIG_MDA_CONSOLEis not set#
# Frame-buffer support
#CONFIG_FB=yCONFIG_DUMMY_CONSOLE=y
#CONFIG_FB_RIVAis not set
#CONFIG_FB_CLGENis not set
#CONFIG_FB_PM2is not set
#CONFIG_FB_CYBER2000is not setCONFIG_FB_VESA=y
#CONFIG_FB_VGA16is not set
#CONFIG_FB_HGAis not setCONFIG_VIDEO_SELECT=y
#CONFIG_FB_MATROXis not set
#CONFIG_FB_ATYis not set
#CONFIG_FB_ATY128is not set
#CONFIG_FB_3DFXis not set
#CONFIG_FB_SISis not set
#CONFIG_FB_VIRTUALis not set
#CONFIG_FBCON_ADVANCEDis not setCONFIG_FBCON_CFB8=yCONFIG_FBCON_CFB16=yCONFIG_FBCON_CFB24=yCONFIG_FBCON_CFB32=y
#CONFIG_FBCON_FONTWIDTH8_ONLYis not set
#CONFIG_FBCON_FONTSis not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y#
# Sound
#CONFIG_SOUND=y
#CONFIG_SOUND_CMPCIis not set
#CONFIG_SOUND_EMU10K1is not set
#CONFIG_SOUND_FUSIONis not set
#CONFIG_SOUND_CS4281is not set
#CONFIG_SOUND_ES1370is not set
#CONFIG_SOUND_ES1371is not set
#CONFIG_SOUND_ESSSOLO1is not set
#CONFIG_SOUND_MAESTROis not set
#CONFIG_SOUND_SONICVIBESis not set
#CONFIG_SOUND_TRIDENTis not set
#CONFIG_SOUND_MSNDCLASis not set
#CONFIG_SOUND_MSNDPINis not set
#CONFIG_SOUND_VIA82CXXXis not setCONFIG_SOUND_OSS=y
#CONFIG_SOUND_TRACEINITis not setCONFIG_SOUND_DMAP=y
#CONFIG_SOUND_AD1816is not set
#CONFIG_SOUND_SGALAXYis not set
#CONFIG_SOUND_ADLIBis not set
#CONFIG_SOUND_ACI_MIXERis not set
#CONFIG_SOUND_CS4232is not set
#CONFIG_SOUND_SSCAPEis not set
#CONFIG_SOUND_GUSis not set
#CONFIG_SOUND_ICHis not set
#CONFIG_SOUND_VMIDIis not set
#CONFIG_SOUND_TRIXis not set
#CONFIG_SOUND_MSSis not set
#CONFIG_SOUND_MPU401is not set
#CONFIG_SOUND_NM256is not set
#CONFIG_SOUND_MAD16is not set
#CONFIG_SOUND_PASis not set
#CONFIG_SOUND_PSSis not setCONFIG_SOUND_SB=yCONFIG_SOUND_AWE32_SYNTH=y
#CONFIG_SOUND_WAVEFRONTis not set
#CONFIG_SOUND_MAUIis not setCONFIG_SOUND_YM3812=y
#CONFIG_SOUND_OPL3SA1is not set
#CONFIG_SOUND_OPL3SA2is not set
#CONFIG_SOUND_YMPCIis not set
#CONFIG_SOUND_YMFPCIis not set
#CONFIG_SOUND_UART6850is not set
#CONFIG_SOUND_AEDSP16is not set
#CONFIG_SOUND_TVMIXERis not set#
# USB support
#
#CONFIG_USBis not set#
# Kernel hacking
#CONFIG_MAGIC_SYSRQ=y
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://vger.kernel.org/lkml/