Skip to contentSkip to conversation

piix.c and tuning question

DISCUSSION [email protected] 2 participants 3 messages Feb 14, 2001

lore
Share & tools
lore
#0 lore raw

I have a box w/ the following controllers:

00:00.0 Host bridge: Intel Corporation 430HX - 82439HX TXC [Triton II] (rev 03) 00:07.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] (rev 01) 00:07.1 IDE interface: Intel Corporation 82371SB PIIX3 IDE [Natoma/Triton II]

I regularly see the following, during high i/o:

Feb 14 02:15:27 inkbay kernel: hdd: timeout waiting for DMA
Feb 14 02:15:27 inkbay kernel: ide_dmaproc: chipset supported ide_dma_timeout func only: 14
Feb 14 02:15:27 inkbay kernel: hdd: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
Feb 14 02:21:13 inkbay kernel: hdc: DMA disabled
Feb 14 02:21:13 inkbay kernel: hdd: DMA disabled
Feb 14 02:21:22 inkbay kernel: hdd: timeout waiting for DMA
Feb 14 02:21:22 inkbay kernel: ide_dmaproc: chipset supported ide_dma_timeout func only: 14
Feb 14 02:21:22 inkbay kernel: hdd: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }

(the DMA being disabled was me manually doing an hdparm -d0)

According to Documentation/Configure.help:

Intel PIIXn chipsets support
CONFIG_BLK_DEV_PIIX
This driver adds PIO mode setting and tuning for all PIIX IDE controllers by Intel. Since the BIOS can sometimes improperly tune PIO 0-4 mode settings, this allows dynamic tuning of the chipset via the standard end-user tool 'hdparm'.

Please read the comments at the top of drivers/ide/piix.c.

If you say Y here, you should also say Y to "PIIXn Tuning support", below.

If unsure, say N.

PIIXn Tuning support
CONFIG_PIIX_TUNING
This driver extension adds DMA mode setting and tuning for all PIIX IDE controllers by Intel. Since the BIOS can sometimes improperly set up the device/adapter combination and speed limits, it has become a necessity to back/forward speed devices as needed.

Case 430HX/440FX PIIX3 need speed limits to reduce UDMA to DMA mode 2 if the BIOS can not perform this task at initialization.

If unsure, say N.

Obviously, the BIOS is not performing the DMA mode reduction, and must be done maually. However, that's about all the information I can gather about this problem. Has anyone looked at the top of piix.c (other than the IDE maintainer, that is)? It's quite cryptic:
* | PIO 4 | MW2 | e3 | a3 | b | piix_tune_drive(drive, 4);
*
* sitre = word40 & 0x4000; primary
* sitre = word42 & 0x4000; secondary
*
* 44 8421|8421 hdd|hdb
*
* 48 8421 hdd|hdc|hdb|hda udma enabled
*
* 0001 hda
Wtf is a sitre? What are these odd numbers? And where is any useful info that, as a piix driver _user_, I might be able to use? Is it merely DMA which I want to tune, or do I want to mess w/ PIO modes (marked as dangerous in hdparm) as well?

Signature · 6 lines
"... being a Linux user is sort of like living in a house inhabited
by a large family of carpenters and architects. Every morning when
you wake up, the house is a little different. Maybe there is a new
turret, or some walls have moved. Or perhaps someone has temporarily
removed the floor under your bed." - Unix for Dummies, 2nd Edition
        -- found in the .sig of Rob Riggs, [email protected]
#1 lore raw

hmmm this is my chipset:

Which motherboard do you have?

00:00.0 Host bridge: Intel Corporation 430HX - 82439HX TXC [Triton II] (rev 03) 00:07.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] (rev 01) 00:07.1 IDE interface: Intel Corporation 82371SB PIIX3 IDE [Natoma/Triton II]

i've had irq timeouts but they were due to a slow CD-ROM causing the two DMA drives to timeout (don't know why).

ive never seen ide_dmaproc though.

This is my following hdparm config

hdparm -d 1 -X34 -u1 -k 1 /dev/hdb
hdparm -d 1 -X34 -u1 -k 1 /dev/hda

for both drives, one of them us a UDMA66 but this Pentium 200Mhz cant do UDMA even ;/

I have a AP53/AX AcerOpen Motherboard.

Shawn.

Quoted 78 lines · [email protected] wrote:

I have a box w/ the following controllers:

00:00.0 Host bridge: Intel Corporation 430HX - 82439HX TXC [Triton II] (rev 03) 00:07.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] (rev 01) 00:07.1 IDE interface: Intel Corporation 82371SB PIIX3 IDE [Natoma/Triton II]

I regularly see the following, during high i/o:

Feb 14 02:15:27 inkbay kernel: hdd: timeout waiting for DMA
Feb 14 02:15:27 inkbay kernel: ide_dmaproc: chipset supported ide_dma_timeout func only: 14
Feb 14 02:15:27 inkbay kernel: hdd: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
Feb 14 02:21:13 inkbay kernel: hdc: DMA disabled
Feb 14 02:21:13 inkbay kernel: hdd: DMA disabled
Feb 14 02:21:22 inkbay kernel: hdd: timeout waiting for DMA
Feb 14 02:21:22 inkbay kernel: ide_dmaproc: chipset supported ide_dma_timeout func only: 14
Feb 14 02:21:22 inkbay kernel: hdd: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }

(the DMA being disabled was me manually doing an hdparm -d0)

According to Documentation/Configure.help:

Intel PIIXn chipsets support
CONFIG_BLK_DEV_PIIX
This driver adds PIO mode setting and tuning for all PIIX IDE controllers by Intel. Since the BIOS can sometimes improperly tune PIO 0-4 mode settings, this allows dynamic tuning of the chipset via the standard end-user tool 'hdparm'.

Please read the comments at the top of drivers/ide/piix.c.

If you say Y here, you should also say Y to "PIIXn Tuning support", below.

If unsure, say N.

PIIXn Tuning support
CONFIG_PIIX_TUNING
This driver extension adds DMA mode setting and tuning for all PIIX IDE controllers by Intel. Since the BIOS can sometimes improperly set up the device/adapter combination and speed limits, it has become a necessity to back/forward speed devices as needed.

Case 430HX/440FX PIIX3 need speed limits to reduce UDMA to DMA mode 2 if the BIOS can not perform this task at initialization.

If unsure, say N.

Obviously, the BIOS is not performing the DMA mode reduction, and must be done maually. However, that's about all the information I can gather about this problem. Has anyone looked at the top of piix.c (other than the IDE maintainer, that is)? It's quite cryptic:
* | PIO 4 | MW2 | e3 | a3 | b | piix_tune_drive(drive, 4);
*
* sitre = word40 & 0x4000; primary
* sitre = word42 & 0x4000; secondary
*
* 44 8421|8421 hdd|hdb
*
* 48 8421 hdd|hdc|hdb|hda udma enabled
*
* 0001 hda
Wtf is a sitre? What are these odd numbers? And where is any useful info that, as a piix driver _user_, I might be able to use? Is it merely DMA which I want to tune, or do I want to mess w/ PIO modes (marked as dangerous in hdparm) as well?

--
"... being a Linux user is sort of like living in a house inhabited by a large family of carpenters and architects. Every morning when you wake up, the house is a little different. Maybe there is a new turret, or some walls have moved. Or perhaps someone has temporarily removed the floor under your bed." - Unix for Dummies, 2nd Edition
-- found in the .sig of Rob Riggs, [email protected]
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#2 lore raw
In reply to [email protected]
Quoted 4 lines · Shawn Starr

hmmm this is my chipset:

Which motherboard do you have?

No clue, it's an old p166, and I'm not about to open up the case..

Quoted 9 lines

00:00.0 Host bridge: Intel Corporation 430HX - 82439HX TXC [Triton II] (rev 03) 00:07.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] (rev 01) 00:07.1 IDE interface: Intel Corporation 82371SB PIIX3 IDE [Natoma/Triton II]

i've had irq timeouts but they were due to a slow CD-ROM causing the two DMA drives to timeout (don't know why).

ive never seen ide_dmaproc though.

Me neither, which is why I initially couldn't figure out what was wrong.. Since setting -X34, however, I haven't had any more ide problems.

Quoted 5 lines

This is my following hdparm config

hdparm -d 1 -X34 -u1 -k 1 /dev/hdb
hdparm -d 1 -X34 -u1 -k 1 /dev/hda

I don't use -k1, since I rely on the OS to set features if something is messed up.

Has -u1 made much of a difference for you?

Quoted 7 lines

for both drives, one of them us a UDMA66 but this Pentium 200Mhz cant do UDMA even ;/

I have a AP53/AX AcerOpen Motherboard.

Shawn.

Signature · 6 lines
"... being a Linux user is sort of like living in a house inhabited
by a large family of carpenters and architects. Every morning when
you wake up, the house is a little different. Maybe there is a new
turret, or some walls have moved. Or perhaps someone has temporarily
removed the floor under your bed." - Unix for Dummies, 2nd Edition
        -- found in the .sig of Rob Riggs, [email protected]