Skip to contentSkip to conversation

ide / usb problem

DISCUSSION jerry 3 participants 3 messages Feb 24, 2001 – Feb 25, 2001

lore
Share & tools
lore

jerry

author
#0 lore raw

I get the following message when copying a 300MB directory under 2.4.2.

uhci:host system error, PCI problems?
uhci:host controller halted, very bad

This does not happen under 2.4.1 and it happens every time under 2.4.2. The system still runs fine except for usb mouse.
All of the files in the directory are copied correctly.

It happens when dma is enabled by hdparm -d1 /dev/hda or when dma is enabled automatically by the kernel.

I have an Abit kt7 mb with the kt133 chipset,Athlon 900 , 128MB mem, quantum fireball 20G disk, gcc 2-95-2 , glibc 2-2-1.

There are no problems with dma disabled.

I was not sure if the VIA82CXXX option should be set with the via kt133 chipset , but setting it results in hundreds of

    hda: dma_intr:status=0x51 { DriveReady SeekComplete Error }
    hda: dma_intr:error=0x84 { DriveStatusError BadCRC }

mesages along with the uhci: errors mentioned above. Again , the directory was copied correctly.

Is there anyway to get 2.4.2 to use dma and not turn off my usb mouse ?

thanks jpd

#1 lore raw
Quoted 4 lines

I get the following message when copying a 300MB directory under 2.4.2.

uhci:host system error, PCI problems?
uhci:host controller halted, very bad

The USB code should recover from that , if it doesnt report it to the USB folks.

Quoted 6 lines

I was not sure if the VIA82CXXX option should be set with the via kt133 chipset , but setting it results in hundreds of

    hda: dma_intr:status=0x51 { DriveReady SeekComplete Error }
    hda: dma_intr:error=0x84 { DriveStatusError BadCRC }

mesages along with the uhci: errors mentioned above. Again , the directory was copied correctly.

That indicates cable problems. The CRC will avoid bad transfers as it will do retries

Alan

#2 lore raw
In reply to jerry

...

Quoted 6 lines

It happens when dma is enabled by hdparm -d1 /dev/hda or when dma is enabled automatically by the kernel.

I have an Abit kt7 mb with the kt133 chipset,Athlon 900 , 128MB mem, quantum fireball 20G disk, gcc 2-95-2 , glibc 2-2-1.

Quoted 7 lines

There are no problems with dma disabled.

I was not sure if the VIA82CXXX option should be set with the via kt133 chipset , but setting it results in hundreds of

    hda: dma_intr:status=0x51 { DriveReady SeekComplete Error }
    hda: dma_intr:error=0x84 { DriveStatusError BadCRC }

mesages along with the uhci: errors mentioned above.

...

Try passing kernel params (eg- idebus=33 ide0=ata66 ide1=ata6) rather than relying on hdparm to set up disks.

I'm on 2.2.19pre8 + ide.2.2.18.1221 but same board and cables, zero errors. Also run a check with nothing but graphics, kbd, disks. KA7 seems to be particularly edgy with some addon cards (ES1370 & Promise controller in my case) and <300W power (compared to P3B-F).

rgds,
tim

# hdparm -iv /dev/hdc

/dev/hdc:

 multcount    =  0 (off)
 I/O support  =  0 (default 16-bit)
 unmaskirq    =  0 (off)
 using_dma    =  1 (on)
 keepsettings =  0 (off)
 nowerr       =  0 (off)
 readonly     =  0 (off)
 readahead    =  8 (on)

geometry = 2501/255/63, sectors = 40188960, start = 0

Model=IBM-DTLA-307020, FwRev=TX3OA50C, SerialNo=YH0YHF45553 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40 BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=off CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=40188960 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4 udma5

# hdparm -tT /dev/hdc

/dev/hdc:
Timing buffer-cache reads: 128 MB in 0.94 seconds =136.17 MB/sec
Timing buffered disk reads: 64 MB in 1.87 seconds = 34.22 MB/sec

# lspci
00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 0391 (rev
02)
00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device 8391
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super] (rev
22)
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev
10)
00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
(rev 30)
00:08.0 FireWire (IEEE 1394): Texas Instruments TSB12LV23 OHCI Compliant
IEEE-1394 Controller
00:09.0 Multimedia audio controller: Ensoniq ES1370 [AudioPCI]
00:0b.0 Ethernet controller: Lite-On Communications Inc LNE100TX (rev
20)
01:00.0 VGA compatible controller: nVidia Corporation Riva TNT2 Model 64
(rev 11)

CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDEDMA_AUTO=y
CONFIG_IDEDMA_PCI_EXPERIMENTAL=y
CONFIG_BLK_DEV_VIA82CXXX=y

Linux version 2.2.19pre8+IDE (root@abit) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #8 Thu Feb 22 18:12:29 PST 2001 USER-provided physical RAM map:
USER: 0009f000 @ 00000000 (usable)
USER: 1ff00000 @ 00100000 (usable)
Detected 800062 kHz processor.
ide_setup: idebus=33
ide_setup: ide0=ata66
ide_setup: ide1=ata66
Console: colour VGA+ 80x25
Calibrating delay loop... 1595.80 BogoMIPS
Memory: 517196k/524288k available (1120k kernel code, 412k reserved, 5512k data, 48k init)
Dentry hash table entries: 65536 (order 7, 512k)
Buffer cache hash table entries: 524288 (order 9, 2048k) Page cache hash table entries: 131072 (order 7, 512k)
CPU: L1 I Cache: 64K L1 D Cache: 64K
CPU: L2 Cache: 512K
CPU: AMD Athlon(tm) Processor stepping 02
Checking 386/387 coupling... OK, FPU using exception 16 error reporting. Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch ([email protected])
PCI: PCI BIOS revision 2.10 entry at 0xfb4d0
...
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 33MHz system bus speed for PIO modes
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VT 8371
Chipset Core ATA-66
VP_IDE: ATA-66/100 forced bit set (WARNING)!!
Split FIFO Configuration: 8 Primary buffers, threshold = 1/2
8 Second. buffers, threshold = 1/2
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
ide0: VIA Bus-Master (U)DMA Timing Config Success
VP_IDE: ATA-66/100 forced bit set (WARNING)!!

    ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA

ide1: VIA Bus-Master (U)DMA Timing Config Success
hda: IBM-DTLA-307020, ATA DISK drive
hdb: YAMAHA CRW4416E, ATAPI CDROM drive
hdc: IBM-DTLA-307020, ATA DISK drive
hdd: HP COLORADO 20GB, ATAPI TAPE drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: IBM-DTLA-307020, 19623MB w/1916kB Cache, CHS=2501/255/63, UDMA(66)
hdc: IBM-DTLA-307020, 19623MB w/1916kB Cache, CHS=39870/16/63, UDMA(66)
...

--