2.2.20pre1: Problems with SMP
Hi,
Just booted up 2.2.20pre1 and am getting some funny results. The system boots but is very slow. Every few seconds I get:
Stuck on TLB IPI wait (CPU#0)
Booting vanilla 2.2.19 works fine. The machine is an Intel Pentium III 850MHZ on an Abit VP6 board. If any further information is needed, let me know.
Regards,
Shane
Signature · 5 lines
Shane Wegner: [email protected] http://www.cm.nu/~shane/ PGP: 1024D/FFE3035D A0ED DAC4 77EC D674 5487 5B5C 4F89 9A4E FFE3 035D
Quoted 8 lines
Just booted up 2.2.20pre1 and am getting some funny results. The system boots but is very slow. Every few seconds I get:
Stuck on TLB IPI wait (CPU#0)Booting vanilla 2.2.19 works fine. The machine is an Intel Pentium III 850MHZ on an Abit VP6 board. If any further information is needed, let me know.
Can you back out the change to io_apic.c and tell me if that fixes it. If so let Johannes Erdfelt and I know.
Quoted 11 lines · Alan Cox
Quoted 8 lines
Just booted up 2.2.20pre1 and am getting some funny results. The system boots but is very slow. Every few seconds I get:
Stuck on TLB IPI wait (CPU#0)Booting vanilla 2.2.19 works fine. The machine is an Intel Pentium III 850MHZ on an Abit VP6 board. If any further information is needed, let me know.
Can you back out the change to
io_apic.cand tell me if that fixes it. If so let Johannes Erdfelt and I know.
That does indeed correct the problem. 2.2.20pre1 now works as expected.
Shane
Signature · 5 lines
Shane Wegner: [email protected] http://www.cm.nu/~shane/ PGP: 1024D/FFE3035D A0ED DAC4 77EC D674 5487 5B5C 4F89 9A4E FFE3 035D
Quoted 10 lines · Shane Wegner
Quoted 9 lines · Alan Cox
Quoted 8 lines
Just booted up 2.2.20pre1 and am getting some funny results. The system boots but is very slow. Every few seconds I get:
Stuck on TLB IPI wait (CPU#0)Booting vanilla 2.2.19 works fine. The machine is an Intel Pentium III 850MHZ on an Abit VP6 board. If any further information is needed, let me know.
Quoted 5 lines
Quoted 2 lines
Can you back out the change to
io_apic.cand tell me if that fixes it. If so let Johannes Erdfelt and I know.That does indeed correct the problem. 2.2.20pre1 now works as expected.
Hmm, that uses a VIA based chipset. I didn't know they did SMP yet. Does 2.4 work on this system?
JE
Quoted 7 lines · Johannes Erdfelt
Quoted 3 lines · Shane Wegner
That does indeed correct the problem. 2.2.20pre1 now works as expected.
Hmm, that uses a VIA based chipset. I didn't know they did SMP yet. Does 2.4 work on this system?
The last 2.4 kernel I tried was 2.4.3 I believe and it worked fine more or less. I haven't tried any later 2.4 kernels yet.
Shane
Signature · 5 lines
Shane Wegner: [email protected] http://www.cm.nu/~shane/ PGP: 1024D/FFE3035D A0ED DAC4 77EC D674 5487 5B5C 4F89 9A4E FFE3 035D
Quoted 6 lines · Shane Wegner
Quoted 5 lines · Johannes Erdfelt
Quoted 3 lines · Shane Wegner
That does indeed correct the problem. 2.2.20pre1 now works as expected.
Quoted 6 lines
Quoted 2 lines
Hmm, that uses a VIA based chipset. I didn't know they did SMP yet. Does 2.4 work on this system?
The last 2.4 kernel I tried was 2.4.3 I believe and it worked fine more or less. I haven't tried any later 2.4 kernels yet.
That's fine. The I/O APIC code is different and I tried to make the 2.2 code work like the 2.4 code with minimal changes. However, the changes aren't trivial. I'll take a quick look and see if I can find any more significant differences.
I wonder if I have a VIA board laying around here.
JE
Quoted 6 lines · Shane Wegner
Quoted 5 lines · Johannes Erdfelt
Quoted 3 lines · Shane Wegner
That does indeed correct the problem. 2.2.20pre1 now works as expected.
Quoted 6 lines
Quoted 2 lines
Hmm, that uses a VIA based chipset. I didn't know they did SMP yet. Does 2.4 work on this system?
The last 2.4 kernel I tried was 2.4.3 I believe and it worked fine more or less. I haven't tried any later 2.4 kernels yet.
Could you try this patch? It applies on top of 2.2.20pre1
It also cleans up a couple of comments
JE
i386/kernel/io_apic.c renamed from i386/kernel/io_apic.c.old +4 -2
@@ -204,6 +204,8 @@/* * We disable IO-APIC IRQs by setting their 'destination CPU mask' to * zero. Trick by Ramesh Nalluri. +* Not anymore. This causes problems on some IO-APIC's, notably AMD 760MP's +* So we do it a more 2.4 kind of way now which should be safer -jerdfelt */ DO_ACTION( mask, 0, |= 0x00010000, io_apic_sync(entry->apic))/* mask = 1 */ DO_ACTION( unmask, 0, &= 0xfffeffff, ) /* mask = 0 */
@@ -646,8 +648,8 @@ entry.delivery_mode = dest_LowestPrio; entry.dest_mode =1 ;/* logical delivery */ - entry.mask =0 ;/* enable IRQ */ - entry.dest.logical.logical_dest =0xff ;/* but no route */ + entry.mask =1 ;/* disable IRQ */ + entry.dest.logical.logical_dest =0xff ; idx =find_irq_entry (apic,pin,mp_INT);if (idx ==-1 ) {
Quoted 4 lines · Johannes Erdfelt
Could you try this patch? It applies on top of 2.2.20pre1
It also cleans up a couple of comments
That fixes it alright.
Shane
Signature · 5 lines
Shane Wegner: [email protected] http://www.cm.nu/~shane/ PGP: 1024D/FFE3035D A0ED DAC4 77EC D674 5487 5B5C 4F89 9A4E FFE3 035D
Quoted 6 lines · Shane Wegner
Quoted 3 lines · Johannes Erdfelt
Could you try this patch? It applies on top of 2.2.20pre1
It also cleans up a couple of comments
That fixes it alright.
Excellent. Alan, could you apply the patch to 2.2.20pre2?
JE