Skip to contentSkip to conversation

FIC AD11(AMD 761/VIA 686B) AGP port not supported

DISCUSSION Joshua Corbin 2 participants 2 messages May 18, 2001

lore
Share & tools
lore
#0 lore raw

The Motherboard is a FIC AD11(AMD 761/VIA 686B chipset). Vid-card is a radeon 32M ddr model.

Whenever I startx with the radeon driver, the machine hangs, forced to use reset switch, not even C-A-Del works. But with the generic vga driver I get all of 16 colors at less than 640x480.

Here are relevant dmesg lines:
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: Unsupported AMD chipset (device id: 700e), you might want to try agp_try_unsupported=1.
agpgart: no supported devices found.

What does agp_try_unsupported mean? Where do I set this setting?

and relevant lspci:
00:00.0 Host bridge: Advanced Micro Devices [AMD]: Unknown device 700e (rev 12)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32 set
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at e3100000 (32-bit, prefetchable) [size=4K]
Region 2: I/O ports at d000 [disabled] [size=4]
Capabilities: [a0] AGP version 2.0
Status: RQ=15 SBA+ 64bit- FW+ Rate=421
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=

00:01.0 PCI bridge: Advanced Micro Devices [AMD]: Unknown device 700f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: e0000000-e1ffffff
Prefetchable memory behind bridge: d8000000-dfffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-

Also attached are the full dmesg and lspci output.

Please help, as it is I am force to use windows to get anything done (that too needed updated drivers before it would work properly).

Thanks in advance -- Josh

Signature · 4 lines
Get your free email from www.linuxmail.org 


Powered by Outblaze
#1 lore raw
Quoted 5 lines

agpgart: Maximum main memory to use for agp memory: 94M
agpgart: Unsupported AMD chipset (device id: 700e), you might want to try agp_try_unsupported=1.
agpgart: no supported devices found.

What does agp_try_unsupported mean? Where do I set this setting?

It says 'assume this chipset is generically like the ones from that vendor I already know about specifically'

rmmod agpgart (if loaded)
modprobe agpgart agp_try_unsupported=1

Be aware that it might crash the box of course

And report if it worked