Skip to contentSkip to conversation

Current tulip driver from 2.4.5 is plain broken

DISCUSSION J Brook 2 participants 2 messages May 29, 2001

lore
Share & tools
lore

J Brook

author
#0 lore raw
Quoted 7 lines · Michal Jaegermann

I mentioned that before but this should be stated clearly. As far as I am concerned "Linux Tulip driver version 0.9.15-pre2 (May 16, 2001)", as used in 2.4.5 - and other kernels - is totally buggered. It comes up, and ethernet interfaces can be configured, but does not matter how I am playing with options I cannot get a single packet through.

Quoted 7 lines

Replacing it in 2.4.5 with "Linux Tulip driver version 0.9.14d (April 3, 2001)", which I have handy, restores sanity immediately and a network simply works without any heroic efforts.

My NIC is "Digital DS21143 Tulip rev 65 at 0x8800". BTW - a version "tulip-1.1.7" from sourceforge behaves exactly like 0.9.15-pre2.

I see exactly the same (broken!) behaviour here. The last kernel
that
works for me in 2.4.4-ac6, which I'm running at the moment. All subsequent -ac kernels and 2.4.5-pre4 and above are broken. I reported
the bug last week. Quick system summary: RH7.1, Duron, KT133, Network card chip "Digital 21041-AA". I get the same problem as above (working
kernels set half-duplex, broken kernels set full-duplex). More details
available on request, or at
http://boudicca.tux.org/hypermail/linux-kernel/2001week21/0278.html

Thanks!

John
----------------
[email protected]

#1 lore raw
Quoted 13 lines · J Brook

I see exactly the same (broken!) behaviour here. The last kernel
that
works for me in 2.4.4-ac6, which I'm running at the moment. All subsequent -ac kernels and 2.4.5-pre4 and above are broken. I reported
the bug last week. Quick system summary: RH7.1, Duron, KT133, Network card chip "Digital 21041-AA". I get the same problem as above (working
kernels set half-duplex, broken kernels set full-duplex). More details
available on request, or at
http://boudicca.tux.org/hypermail/linux-kernel/2001week21/0278.html

Quoted 3 lines

Thanks!

John

RH 7.1 running kernel 2.4.5-ac3, Dual Xeon 450, Supermicro S2DGE, Network card
Macronix, Inc. [MXIC] MX987x5.

tulip-diag.c:v2.08 5/15/2001 Donald Becker ([email protected])
http://www.scyld.com/diag/index.html
Index #1: Found a Macronix 98715 PMAC adapter at 0xe800. Macronix 98715 PMAC chip registers at 0xe800:
0x00: fff88000 ffffffff ffffffff 1fefc000 1fefc200 e4660000 01a82202
e7ffebef
0x40: fffe0000 0fffcf08 ffffffff fffe0000 40a1d0cc ffff0000 ffffffff
fff00000
Extended registers:
80: 0f340000 0f340000 0f340000 0f340000 0f340000 0f340000 fc4ffff0
f84ffff0
a0: 2001527f 2001527f 2001527f 2001527f 2001527f 2001527f 2001527f
2001527f
c0: 2001527f 2001527f 2001527f 2001527f 2001527f 2001527f 2001527f
2001527f
e0: 2001527f 2001527f 2001527f 2001527f 2001527f 2001527f 2001527f
2001527f
Port selection is 10mpbs-serial 100baseTx scrambler, full-duplex. Transmit started, Receive started, full-duplex.
The Rx process state is 'Waiting for packets'.
The Tx process state is 'Idle'.
The transmit unit is set to store-and-forward.
EEPROM 64 words, 6 address bits.
A simplifed EEPROM data table was found.
The EEPROM does not contain transceiver control information.
No MII transceivers found!

Works great, no problems at all.