Skip to contentSkip to conversation

IDE Problems on SIS 735?

DISCUSSION [email protected] 3 participants 5 messages Sep 5, 2001 – Sep 11, 2001

lore
Share & tools
lore
#0 lore raw

Hi,
I've been having repeated DMA problems on my SIS 735 based board, I've done a search for the meaning of the error message I'm getting, but I must be looking in the wrong places since I can't seem to find something that explains it fully. Since this chipset is fairly new I thought I'd mention it here to see if anyone has an idea what might be wrong (I'm suspecting the cables, but I've already swapped them over once..).

I've stuck some (possibly) useful/relevant information below. I'm running 2.4.9-ac7.

Cheers,
Adrian.

(Boot information)
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes
SIS5513: IDE controller on PCI bus 00 dev 15
SIS5513: chipset revision 208
SIS5513: not 100% native mode: will probe irqs later SiS735

    ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA

hda: Maxtor 91024U4, ATA DISK drive
hdb: FUJITSU MPE3064AT, ATA DISK drive
hdc: Hewlett-Packard CD-Writer Plus 9300, ATAPI CD/DVD-ROM drive
hdd: Pioneer DVD-ROM ATAPIModel DVD-104S 020, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 19999728 sectors (10240 MB) w/2048KiB Cache, CHS=1244/255/63, UDMA(66)
hdb: 12672450 sectors (6488 MB) w/512KiB Cache, CHS=788/255/63, UDMA(33) Partition check:
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 >
hdb: hdb1 hdb2 < hdb5 >

(Error message itself)
hda: timeout waiting for DMA
ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command

(Result from "cat /proc/ide/sis")
--------------- Primary Channel ---------------- Secondary Channel -------------

Channel Status: On 	 	 	 	 On 
Operation Mode: Compatible 	 	 	 Compatible 
Cable Type:     80 pins 	 	 	 80 pins
Prefetch Count: 512 	 	 	 	 512
Drive 0:        Postwrite Enabled 	 	 Postwrite Disabled

Prefetch Enabled Prefetch Disabled
UDMA Enabled UDMA Enabled
UDMA Cycle Time 2 CLK UDMA Cycle Time 2 CLK
Data Active Time 2 PCICLK Data Active Time 5 PCICLK
Data Recovery Time 1 PCICLK Data Recovery Time 1 PCICLK
Drive 1: Postwrite Enabled Postwrite Disabled
Prefetch Enabled Prefetch Disabled
UDMA Enabled UDMA Enabled
UDMA Cycle Time 2 CLK UDMA Cycle Time 2 CLK
Data Active Time 2 PCICLK Data Active Time 2 PCICLK
Data Recovery Time 1 PCICLK Data Recovery Time 1 PCICLK

#1 lore raw
Quoted 5 lines

search for the meaning of the error message I'm getting, but I must be looking in the wrong places since I can't seem to find something that explains it fully. Since this chipset is fairly new I thought I'd mention it here to see if anyone has an idea what might be wrong (I'm suspecting the cables, but I've already swapped them over once..).

The driver tried to do a UDMA transfer, and waited and waited, and gave up on it. With cable errors I'd expect to see a badCRC message or two.

Does it behave better with an older kernel (say 2.4.7 or so) ?

#2 lore raw
In reply to [email protected]
Quoted 5 lines · Alan Cox

The driver tried to do a UDMA transfer, and waited and waited, and gave up on it. With cable errors I'd expect to see a badCRC message or two.

Does it behave better with an older kernel (say 2.4.7 or so) ?

Alan,
Nope. Been having this problem since I installed the motherboard. I'll have to see about getting another cable, I think - I've used the one that came with the motherboard, and another that came with my Maxtor HD. Cheers,
Adrian.

Signature · 1 line
PGP Public Key at http://www.corrosive.freeserve.co.uk/text/pubkey.asc
#3 lore raw

Re: IDE Problems on SIS 735? (continued)

In reply to [email protected]

Okay, I've now changed the IDE cable attached to my hard drives twice, and I'm still getting IDE DMA problems - has anyone else with a SIS 735 based motherboard been having any problems, because I'm running short of ideas? Also - what are the chances of data corruption from these errors? Thanks,
Adrian.

(error report)
hda: timeout waiting for DMA
ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status timeout: status=0xd0 { Busy }
hdb: DMA disabled
hda: drive not ready for command
ide0: reset: success

Signature · 1 line
PGP Public Key at http://www.corrosive.freeserve.co.uk/text/pubkey.asc
#4 lore raw

Re: IDE Problems on SIS 735? (continued)

In reply to [email protected]
Quoted 7 lines · Adrian Burgess

Okay, I've now changed the IDE cable attached to my hard drives twice, and I'm still getting IDE DMA problems - has anyone else with a SIS 735 based motherboard been having any problems, because I'm running short of ideas? Also - what are the chances of data corruption from these errors? Thanks,
Adrian.

I'm using the SiS 735 motherboard with ATA/100 IDE, I have an Quantum Bigfoot 8.1G drive, along with two 45G IBM DTLA drives (ATA/100) on controller, I've had no problems beyond some clicking on one of the IBM drives that also happens on a Promise PCI controller (no messages to syslog about it, and S.M.A.R.T. reports no errors (I use smartctl)) 2.4.9 kernel..

Matthew S. Hallacy

Quoted 10 lines

(error report)
hda: timeout waiting for DMA
ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command
hda: status timeout: status=0xd0 { Busy }
hdb: DMA disabled
hda: drive not ready for command
ide0: reset: success