Skip to contentSkip to conversation

HIGMEM, SMP, 2.4.13 and Cerberus

DISCUSSION Joan Batet 4 participants 4 messages Oct 29, 2001

lore
Share & tools
lore

Joan Batet

author
#0 lore raw

Hello all,
I've got a little problem with a new computer we have on our company. The problem is what I try run Cerberus to test the stability of this computer with a 2.4.13 kernel; at the first test the computer went down in 15 minutes; the second test went well, the computer responsivity was good and it was appears to be stable. At this moment I'm going to test again to see if the machine supports it (I hope that ...).
Well, now the problem and the question: what kernel do you think I must put on this computer? I need a rock solid system ... I'm testing 2.4.3 and 2.4.9 too, but 2.4.13 appears to be the best performance kernel ... Thanks in advance,
Joan

The computer:
- Dell PowerEdge 2550
- Dual PIII 1Ghz
- 2Gb ECC SDRAM
- 2 x 36Gb RAID1 (AACRAID)

Linux TESTING 2.4.13 #1 SMP Fri Oct 26 12:30:37 CEST 2001 i686 unknown

Gnu C                  2.95.3
Gnu make               3.79.1
binutils               2.10.91.0.4
util-linux             2.11f
mount                  2.11f
modutils               2.4.5
e2fsprogs              1.24
Linux C Library        2.2.2
Dynamic linker (ldd)   2.2.2
Procps                 2.0.7
Net-tools              1.60
Kbd                    1.04
Sh-utils               2.0

Modules Loaded

#1 lore raw
Quoted 4 lines · Joan Batet

Well, now the problem and the question: what kernel do you think I must put on this computer? I need a rock solid system ... I'm testing 2.4.3 and 2.4.9 too, but 2.4.13 appears to be the best performance kernel ...

2.4.12-ac6 should be able to survive Cerberus.

Rik

Signature · 3 lines
DMCA, SSSCA, W3C?  Who cares?  http://thefreeworld.net/

http://www.surriel.com/		http://distro.conectiva.com/
#2 lore raw

2.4.0 TCP caches ip route

Hi,

I'm using 2.4.0 (but I thing that this is probably a 2.4.X problem). If a execute a telnet command to certain address (like 10.0.0.1). And the routing table says that packets for 10.0.0.1 should be routed to the device dummy0,
The telnet keeps trying to connect. (till here everything is cool). And then I change the routing table so now it should
send those packets to the ppp0 (where 10.0.0.1 is), but the connexion does not get stablished anyway (till I get timeout).

The problem seems to be that the kernel
caches that the device for the connexion should be dummy0. If then, I cancel the telnet and start it again
now (of course) it stablishes a telnet conexion though the ppp0.

This problem does not occur if I use ping instead of telnet (probably because ping uses no socket).

Should not be a mechanism that flushes caches when routing table changes?

If the cached info is attached to the socket structure probably this flushing thing is not quite feasible, am I wrong?

I know you usually don't expect the device though your tcp connection goes to change on the fly, but that actually can happend, and maybe (IMHO) should be supported.

Maybe I'm missing something. (probably ;) )

Regards,

Manel Guerrero

#3 lore raw

Re: 2.4.0 TCP caches ip route

In reply to Rik van Riel

----- Original Message -----
From: "Manel Guerrero Zapata" <[email protected]>
To: "Kernel Mailing List" <[email protected]>
Sent: Monday, October 29, 2001 2:03 PM
Subject: 2.4.0 TCP caches ip route

Quoted 22 lines

Hi,

I'm using 2.4.0 (but I thing that this is probably a 2.4.X problem). If a execute a telnet command to certain address (like 10.0.0.1). And the routing table says that packets for 10.0.0.1 should be routed to the device dummy0,
The telnet keeps trying to connect. (till here everything is cool). And then I change the routing table so now it should
send those packets to the ppp0 (where 10.0.0.1 is), but the connexion does not get stablished anyway (till I get timeout).

The problem seems to be that the kernel
caches that the device for the connexion should be dummy0. If then, I cancel the telnet and start it again
now (of course) it stablishes a telnet conexion though the ppp0.

This problem does not occur if I use ping instead of telnet (probably because ping uses no socket).

Should not be a mechanism that flushes caches when routing table changes?

Quoted 8 lines

If the cached info is attached to the socket structure probably this flushing thing is not quite feasible, am I wrong?

I know you usually don't expect the device though your tcp connection goes to change on the fly, but that actually can happend, and maybe (IMHO) should be supported.

Maybe I'm missing something. (probably ;) )

This sounds like a minor problem. I do think that if you already have an established connection it would work just as you want it to do, but as you describe it you don't have an established TCP connection. What I mean is that you won't exactly loose your connection if you don't even have one at the first place!

_____________________________________________________

|  Martin Eriksson <[email protected]>
|  MSc CSE student, department of Computing Science
|  Umeå University, Sweden