Skip to contentSkip to conversation

USB mouse disconnect/reconnect

DISCUSSION Jan Kasprzak 5 participants 15 messages Dec 11, 2001 – Dec 13, 2001

lore
Share & tools
lore
#0 lore raw

Hello,

I have (maybe HW) problem w/ my USB mouse. From time to time,
the kernel thinks it was disconnected and then reconnected again, altough nobody touched the cables.

It would be OK, but there is a problem: after the reconnect, it become active as /dev/input/mouse1 instead of /dev/input/mouse0, and my X server cannot (of course) find it.

	The system is RH7.2, kernel 2.4.16, Athlon 850 (ABIT KT7).

Here is the dmesg output of the USB after boot:

usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.268 $ time 19:53:08 Dec 5 2001 usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 10 for device 00:07.2
PCI: Sharing IRQ 10 with 00:07.3
PCI: Sharing IRQ 10 with 00:0b.0
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 10 for device 00:07.3
PCI: Sharing IRQ 10 with 00:07.2
PCI: Sharing IRQ 10 with 00:0b.0
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.268:USB Universal Host Controller Interface driver usb.c: registered new driver hid
hid-core.c: v1.8 Andreas Gal, Vojtech Pavlik <[email protected]> hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
hub.c: USB new device connect on bus2/1, assigned device number 2
input0: USB HID v1.00 Mouse [KYE Systems Genius USB Wheel Mouse ] on usb2:2.0
hub.c: USB new device connect on bus2/2, assigned device number 3
input1: USB HID v1.10 Keyboard [Chicony USB Keyboard] on usb2:3.0

And the disconnect/reconnect looks like this:

usb.c: USB disconnect on device 2
hub.c: USB new device connect on bus2/1, assigned device number 4
input0: USB HID v1.00 Mouse [KYE Systems Genius USB Wheel Mouse ] on usb2:4.0

Where the disconnect/reconnect come from, and why the mouse
changes its device number?

-Yenya

Signature · 5 lines
| Jan "Yenya" Kasprzak  <kas at {fi.muni.cz - work | yenya.net - private}> |
| GPG: ID 1024/D3498839      Fingerprint 0D99A7FB206605D7 8B35FCDE05B18A5E |
| http://www.fi.muni.cz/~kas/   Czech Linux Homepage: http://www.linux.cz/ |
Having your own personal custom language dialect might be tempting but it is
normally something only the lisp community do.                    (Alan Cox)
#1 lore raw
Quoted 41 lines · Jan Kasprzak

I have (maybe HW) problem w/ my USB mouse. From time to time,
the kernel thinks it was disconnected and then reconnected again, altough nobody touched the cables.

It would be OK, but there is a problem: after the reconnect, it become active as /dev/input/mouse1 instead of /dev/input/mouse0, and my X server cannot (of course) find it.

	The system is RH7.2, kernel 2.4.16, Athlon 850 (ABIT KT7).

Here is the dmesg output of the USB after boot:

usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.268 $ time 19:53:08 Dec 5 2001 usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 10 for device 00:07.2
PCI: Sharing IRQ 10 with 00:07.3
PCI: Sharing IRQ 10 with 00:0b.0
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 10 for device 00:07.3
PCI: Sharing IRQ 10 with 00:07.2
PCI: Sharing IRQ 10 with 00:0b.0
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.268:USB Universal Host Controller Interface driver usb.c: registered new driver hid
hid-core.c: v1.8 Andreas Gal, Vojtech Pavlik <[email protected]> hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
hub.c: USB new device connect on bus2/1, assigned device number 2
input0: USB HID v1.00 Mouse [KYE Systems Genius USB Wheel Mouse ] on usb2:2.0
hub.c: USB new device connect on bus2/2, assigned device number 3
input1: USB HID v1.10 Keyboard [Chicony USB Keyboard] on usb2:3.0

Quoted 8 lines

And the disconnect/reconnect looks like this:

usb.c: USB disconnect on device 2
hub.c: USB new device connect on bus2/1, assigned device number 4
input0: USB HID v1.00 Mouse [KYE Systems Genius USB Wheel Mouse ] on usb2:4.0

Where the disconnect/reconnect come from, and why the mouse
changes its device number?

It may be because of a flaky cable. Are there any messages above that?

The device number changes because some process still has the first mouse open, so it assigns it the next available unused device.

There's a shared mouse device as well you might find more to your liking.

JE

#2 lore raw
In reply to Jan Kasprzak

Johannes Erdfelt wrote:
: It may be because of a flaky cable. Are there any messages above that? :
No messages from USB (some HW csum failures from the eth0, but
nothing related to my mouse). But you may be right, the mouse is connected via a 5m extension USB cable.

: The device number changes because some process still has the first mouse : open, so it assigns it the next available unused device.
:
: There's a shared mouse device as well you might find more to your : liking.

I'll look at it, thanks. Fortunately I do not use more than one
USB mouse (altough this is a dual-{head,keyboard,mouse} configuration, the other mouse is on the PS/2 port).

-Y.

Signature · 5 lines
| Jan "Yenya" Kasprzak  <kas at {fi.muni.cz - work | yenya.net - private}> |
| GPG: ID 1024/D3498839      Fingerprint 0D99A7FB206605D7 8B35FCDE05B18A5E |
| http://www.fi.muni.cz/~kas/   Czech Linux Homepage: http://www.linux.cz/ |
Having your own personal custom language dialect might be tempting but it is
normally something only the lisp community do.                    (Alan Cox)
#3 lore raw
In reply to Jan Kasprzak
Quoted 6 lines · Jan Kasprzak

Johannes Erdfelt wrote:
: It may be because of a flaky cable. Are there any messages above that? :
No messages from USB (some HW csum failures from the eth0, but
nothing related to my mouse). But you may be right, the mouse is connected via a 5m extension USB cable.

Is it an active extension cable?

JE

#4 lore raw
In reply to Jan Kasprzak

Johannes Erdfelt wrote:
: On Wed, Dec 12, 2001, Jan Kasprzak <[email protected]> wrote:
: > Johannes Erdfelt wrote:
: > : It may be because of a flaky cable. Are there any messages above that? : > :
: > No messages from USB (some HW csum failures from the eth0, but
: > nothing related to my mouse). But you may be right, the mouse is connected : > via a 5m extension USB cable.
:
: Is it an active extension cable?

No. Just a simple passive one.

-Y.

Signature · 5 lines
| Jan "Yenya" Kasprzak  <kas at {fi.muni.cz - work | yenya.net - private}> |
| GPG: ID 1024/D3498839      Fingerprint 0D99A7FB206605D7 8B35FCDE05B18A5E |
| http://www.fi.muni.cz/~kas/   Czech Linux Homepage: http://www.linux.cz/ |
Having your own personal custom language dialect might be tempting but it is
normally something only the lisp community do.                    (Alan Cox)
#5 lore raw
In reply to Jan Kasprzak
Quoted 11 lines · Jan Kasprzak

Johannes Erdfelt wrote:
: On Wed, Dec 12, 2001, Jan Kasprzak <[email protected]> wrote:
: > Johannes Erdfelt wrote:
: > : It may be because of a flaky cable. Are there any messages above that? : > :
: > No messages from USB (some HW csum failures from the eth0, but
: > nothing related to my mouse). But you may be right, the mouse is connected : > via a 5m extension USB cable.
:
: Is it an active extension cable?

Quoted 1 line

No. Just a simple passive one.

There's your problem with disconnects. Those are illegal per the specs.

JE

#6 lore raw
In reply to Jan Kasprzak

[l-k removed from Cc:]

Johannes Erdfelt wrote:
:
: There's your problem with disconnects. Those are illegal per the specs. :
What is the maximum length?

-Y.

Signature · 5 lines
| Jan "Yenya" Kasprzak  <kas at {fi.muni.cz - work | yenya.net - private}> |
| GPG: ID 1024/D3498839      Fingerprint 0D99A7FB206605D7 8B35FCDE05B18A5E |
| http://www.fi.muni.cz/~kas/   Czech Linux Homepage: http://www.linux.cz/ |
Having your own personal custom language dialect might be tempting but it is
normally something only the lisp community do.                    (Alan Cox)
#7 lore raw
In reply to Jan Kasprzak
Quoted 7 lines · Jan Kasprzak

[l-k removed from Cc:]

Johannes Erdfelt wrote:
:
: There's your problem with disconnects. Those are illegal per the specs. :
What is the maximum length?

I haven't looked at the spec lately, but I think 5 meters is the maximum. You can go longer if you use an active cable which is essentially a one port hub. It essentially acts as a repeater.

JE

#8 lore raw
In reply to Jan Kasprzak
Quoted 9 lines · Johannes Erdfelt
Quoted 7 lines · Jan Kasprzak

[l-k removed from Cc:]

Johannes Erdfelt wrote:
:
: There's your problem with disconnects. Those are illegal per the specs. :
What is the maximum length?

Quoted 3 lines

I haven't looked at the spec lately, but I think 5 meters is the maximum. You can go longer if you use an active cable which is essentially a one port hub. It essentially acts as a repeater.

The problem with active cables is that they are very problematic as well. The device plugged in isn't visible to Linux until the cable itself is unplugged and replugged into the computer. I haven't found out why yet.

Signature · 2 lines
Vojtech Pavlik
SuSE Labs
#9 lore raw
In reply to Jan Kasprzak
Quoted 10 lines · Vojtech Pavlik
Quoted 9 lines · Johannes Erdfelt
Quoted 7 lines · Jan Kasprzak

[l-k removed from Cc:]

Johannes Erdfelt wrote:
:
: There's your problem with disconnects. Those are illegal per the specs. :
What is the maximum length?

Quoted 8 lines
Quoted 3 lines

I haven't looked at the spec lately, but I think 5 meters is the maximum. You can go longer if you use an active cable which is essentially a one port hub. It essentially acts as a repeater.

The problem with active cables is that they are very problematic as well. The device plugged in isn't visible to Linux until the cable itself is unplugged and replugged into the computer. I haven't found out why yet.

That's weird. Sounds like a problem specific to that cable. It should just look like a hub and act as one.

Including hot plugging.

JE

#10 lore raw
In reply to Jan Kasprzak
Quoted 20 lines · Johannes Erdfelt
Quoted 10 lines · Vojtech Pavlik
Quoted 9 lines · Johannes Erdfelt
Quoted 7 lines · Jan Kasprzak

[l-k removed from Cc:]

Johannes Erdfelt wrote:
:
: There's your problem with disconnects. Those are illegal per the specs. :
What is the maximum length?

Quoted 8 lines
Quoted 3 lines

I haven't looked at the spec lately, but I think 5 meters is the maximum. You can go longer if you use an active cable which is essentially a one port hub. It essentially acts as a repeater.

The problem with active cables is that they are very problematic as well. The device plugged in isn't visible to Linux until the cable itself is unplugged and replugged into the computer. I haven't found out why yet.

Quoted 4 lines

That's weird. Sounds like a problem specific to that cable. It should just look like a hub and act as one.

Including hot plugging.

Most active extension cables don't look like hubs. They have the electric part of the hub built in, but not the logic one. They're invisible on the USB bus.

Signature · 2 lines
Vojtech Pavlik
SuSE Labs
#11 lore raw
Quoted 3 lines · Vojtech Pavlik

Most active extension cables don't look like hubs. They have the electric part of the hub built in, but not the logic one. They're invisible on the USB bus.

The ones I have seen do act as a hub, and are visible from the host computer.

Peter
--
Peter Svensson ! Pgp key available by finger, fingerprint:
<[email protected]> ! 8A E9 20 98 C1 FF 43 E3 07 FD B9 0A 80 72 70 AF
------------------------------------------------------------------------
Remember, Luke, your source will be with you... always...

#12 lore raw
In reply to Vojtech Pavlik
Quoted 8 lines · Peter Svensson
Quoted 3 lines · Vojtech Pavlik

Most active extension cables don't look like hubs. They have the electric part of the hub built in, but not the logic one. They're invisible on the USB bus.

The ones I have seen do act as a hub, and are visible from the host computer.

I guess I'll have to get me some of those as a replacement to those I have.

Signature · 2 lines
Vojtech Pavlik
SuSE Labs
#13 lore raw
In reply to Jan Kasprzak

On a machine at work with a Logitech USB MouseMan+ and no extension cable and a M$ usb keyboard I see the same thing. Machine is a Dell with PII-400 and BX chipset.
Happens during the night when not in use.

Quoted 31 lines · Jan Kasprzak

Johannes Erdfelt wrote:
: It may be because of a flaky cable. Are there any messages above that? :
No messages from USB (some HW csum failures from the eth0, but
nothing related to my mouse). But you may be right, the mouse is connected via a 5m extension USB cable.

: The device number changes because some process still has the first mouse : open, so it assigns it the next available unused device.
:
: There's a shared mouse device as well you might find more to your : liking.

I'll look at it, thanks. Fortunately I do not use more than one
USB mouse (altough this is a dual-{head,keyboard,mouse} configuration, the other mouse is on the PS/2 port).

-Y.

--

| Jan "Yenya" Kasprzak  <kas at {fi.muni.cz - work | yenya.net - private}> |
| GPG: ID 1024/D3498839      Fingerprint 0D99A7FB206605D7 8B35FCDE05B18A5E |
| http://www.fi.muni.cz/~kas/   Czech Linux Homepage: http://www.linux.cz/ |

Having your own personal custom language dialect might be tempting but it is
normally something only the lisp community do. (Alan Cox)
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#14 lore raw
In reply to Jan Kasprzak

watermodem wrote:
: On a machine at work with a Logitech USB MouseMan+ and no extension : cable and a M$ usb keyboard I see the same thing. Machine is a : Dell with PII-400 and BX chipset.
: Happens during the night when not in use.
:
My mouse is Genius Netscroll, and it also happens during the night
when not in use. It cannot be a power saving, though, because I run distributed.net client on this machine. Chipset is VIA KT133. There is an interesting thinng though: I don't see disconnects/reconnects on the USB keyboard, which is connected via the identical 5m USB extension cable as the USB mouse.

I can try to plug the mouse into another USB port.

-Y.

Signature · 5 lines
| Jan "Yenya" Kasprzak  <kas at {fi.muni.cz - work | yenya.net - private}> |
| GPG: ID 1024/D3498839      Fingerprint 0D99A7FB206605D7 8B35FCDE05B18A5E |
| http://www.fi.muni.cz/~kas/   Czech Linux Homepage: http://www.linux.cz/ |
Having your own personal custom language dialect might be tempting but it is
normally something only the lisp community do.                    (Alan Cox)