EMU10K1: IRQ 10 ?
Hi. I just bought a Sound Blaster Live! 5.1 (SB0100) and tried to install it on Linux 2.4.17. It's my second sound card. The 16 ISA worked but I haven't used it for years.
# modprobe emu10k1
/var/log/messages:
Dec 25 01:02:27 pervalidus kernel: Creative EMU10K1 PCI Audio Driver, version 0.16, 06:46:55 Dec 22 2001 Dec 25 01:02:27 pervalidus kernel: PCI: Found IRQ 10 for device 00:0b.0 Dec 25 01:02:27 pervalidus kernel: emu10k1: EMU10K1 rev 8 model 0x8064 found, IO at 0xa000-0xa01f, IRQ 10 Dec 25 01:02:27 pervalidus kernel: ac97_codec: AC97 Audio codec, id: 0x8384:0x7608 (SigmaTel STAC9708)
/proc/modules:
emu10k1 55360 0 (unused) sound 53676 0 [emu10k1] ac97_codec 9632 0 [emu10k1] soundcore 3460 7 [emu10k1 sound]
# lspci -vv
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 02)
Subsystem: Asustek Computer, Inc.: Unknown device 8033
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: e0800000-e1dfffff
Prefetchable memory behind bridge: e1f00000-e3ffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
Subsystem: Asustek Computer, Inc.: Unknown device 8033
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:04.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at d800 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 12
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 12
Region 4: I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
Subsystem: Asustek Computer, Inc.: Unknown device 8033
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev 78)
Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management NIC
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at a400 [size=128]
Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 08)
Subsystem: Creative Labs: Unknown device 8064
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at a000 [size=32]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.1 Input device controller: Creative Labs SB Live! (rev 08)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at 9800 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 04) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G400 32Mb SDRAM Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (4000ns min, 8000ns max), cache line size 08 Interrupt: pin A routed to IRQ 11 Region 0: Memory at e2000000 (32-bit, prefetchable) [size=32M] Region 1: Memory at e1000000 (32-bit, non-prefetchable) [size=16K] Region 2: Memory at e0800000 (32-bit, non-prefetchable) [size=8M] Expansion ROM at e1ff0000 [disabled] [size=64K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [f0] AGP version 2.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1
When I try to test:
# cat /home/ftp/pub/sound/ra/english.au > /dev/audio zsh: no such device or address: /dev/audio
# cat /home/ftp/pub/sound/ra/english.au > /dev/sound/audio zsh: no such device or address: /dev/sound/audio
My .config:
CONFIG_SOUND=m
# CONFIG_SOUND_BT878 is not set
# CONFIG_SOUND_CMPCI is not setCONFIG_SOUND_EMU10K1=mCONFIG_MIDI_EMU10K1=y
# CONFIG_SOUND_FUSION is not set
# CONFIG_SOUND_CS4281 is not set
# CONFIG_SOUND_ES1370 is not set
# CONFIG_SOUND_ES1371 is not set
# CONFIG_SOUND_ESSSOLO1 is not set
# CONFIG_SOUND_MAESTRO is not set
# CONFIG_SOUND_MAESTRO3 is not set
# CONFIG_SOUND_ICH is not set
# CONFIG_SOUND_RME96XX is not set
# CONFIG_SOUND_SONICVIBES is not set
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_VIA82CXXX is not set
# CONFIG_MIDI_VIA82CXXX is not set
# CONFIG_SOUND_OSS is not set
# CONFIG_SOUND_TVMIXER is not set
I don't have any other OS to test. Any idea ?
I'm using devfs. My devfsd.conf:
REGISTER .* MKOLDCOMPAT UNREGISTER .* RMOLDCOMPAT LOOKUP .* MODLOAD REGISTER tts/1 PERMISSIONS root.uucp 660 REGISTER floppy/.* PERMISSIONS root.floppy 660 REGISTER sound/.* PERMISSIONS root.audio 660 REGISTER snd/.* PERMISSIONS root.audio 660
All entries in /dev are created, including the symbolic links.
Signature · 1 line
0@pervalidus.{net, {dyndns.}org} Tel: 55-21-2717-2399 (Niterói-RJ BR)Quoted 9 lines · Matthew Johnson
Quoted 7 lines · you
Quoted 3 lines
I'd cheat and use sndconfig ot yast2 or whatever else. Failing that I can give you some idea via my modules.conf, but I use SuSE, whcih in turn uses Alsa.
OK, so I'll try ALSA.
My modules.conf just includes 'alias sound emu10k1'.
Dec 25 03:13:38 pervalidus kernel: PCI: Found IRQ 10 for device 00:0b.0
OK, ALSA worked, while OSS from the kernel didn't. I don't know why.
I still have a problem. Sound is very distorted with a lot of noise when I do a 'cat /home/ftp/pub/sound/ra/english.au > /dev/audio' . Maybe my speakers are broken ? I never used them before. Time to do more testing. Yes, I know nothing about sound.
Thank you Matthew. Now if any kernel developer can answer why OSS from the kernel didn't work...
Signature · 1 line
0@pervalidus.{net, {dyndns.}org} Tel: 55-21-2717-2399 (Niterói-RJ BR)Quoted 2 lines
Thank you Matthew. Now if any kernel developer can answer why OSS from the kernel didn't work...
No problem, but whilst you wait maybe this file will help you, just in case you haven't found it yet:
http://www.opensound.com/readme/README.SBLive.html
Main page:
Try the forum too, will know more about sound issues than I currently know.
Merry xmas, don't eat too many Mince pies, or em Mince Pizza with Cokenogg
Matt
Quoted 16 lines · Frédéric L. W. Meunier
Quoted 11 lines · Matthew Johnson
Quoted 8 lines · you
Quoted 4 lines
I'd cheat and use sndconfig ot yast2 or whatever else. Failing that I can give you some idea via my modules.conf, but I use SuSE, whcih in turn uses Alsa.
OK, so I'll try ALSA.
My modules.conf just includes 'alias sound emu10k1'.
Dec 25 03:13:38 pervalidus kernel: PCI: Found IRQ 10 for device 00:0b.0
Quoted 9 lines
OK, ALSA worked, while OSS from the kernel didn't. I don't know why.
I still have a problem. Sound is very distorted with a lot of noise when I do a 'cat
/home/ftp/pub/sound/ra/english.au>/dev/audio' . Maybe my speakers are broken ? I never used them before. Time to do more testing. Yes, I know nothing about sound.
Same for me. But if you use a real application like plaympeg or sox hi.au -t ossdsp /dev/dsp it works fine. I'm using emu10k1 from http://opensource.creative.com
Signature · 4 lines
Hartmut Holz EMail: [email protected] Kieler Straße 231 Phone: +49 4085080014 22525 Hamburg Germany