Mailer Connections
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hi Peter.
Here's the relevant headers of your email as it came to me...
Quoted 8 lines
Received: from ppp12.pool4.mnl.skyinet.net ([202.78.107.12]
helo=localhost.localdomain) by phoenix.infradead.org with esmtp (Exim 4.10) id 17eUmE-0008Fi-00 for [email protected]; Tue, 13 Aug 2002 07:03:36 +0100 Received: from localhost.localdomain (pfheiss@localhost) by localhost.localdomain (8.9.3/8.9.3) with ESMTP id OAA02685; Tue, 13 Aug 2002 14:03:37 +0800
Quoted 6 lines
X-Mailer: exmh version 2.5 07/13/2001 with nmh-1.0.4
To: [email protected]
cc: [email protected], [email protected]
Subject: Re: Mailer Connections
Date: Tue, 13 Aug 2002 14:03:37 +0800
From: Peter <[email protected]>
From those, we can deduce the following:
1. The "Date:" line states when it was posted.
2. The "X-Mailer:" line states the program you used to post it.
3. The "From:" line states the address that was used to post it. As you can see, this is wrong.
4. The "To:" and "cc:" lines state the addresses you posted it to.
5. Reading from the bottom up, the "Received:" lines state the route your message took to get to me. The bottom one is your local box's SendMail reporting that it processed the message on the way out, and the top one is my mailhost confirming receipt thereof.
The top "Received:" line gives the critical evidence when it reports "helo=localhost.localdomain" as this states that your system's hostname is currently set up as localhost.localdomain as stated, and this is also confirmed both by the bottom "Received:" line and by the "From:" line. This is NOT a problem with either Exim or SendMail but with the general configuration of your system.
Quoted 5 lines
Quoted 5 lines
Quoted 2 lines
How do I revert back that I can mail again with any mail program especially exmh and with any ISP?
As a result, the solution may be as simple as setting the hostname for your machine to match that of your preferred ISP by editing the
.> file / etc/sysconfig/network and putting the full; hostname on the
Quoted 4 lines
. HOSTNAME= line, then rebooting your system.
I did that now. It had localhost.localdomain. I changed if to "Peter". Can there be more than one name and if so how are they separated?
There can only be one name,. Assuming you are NOT running a LAN of your home, it should correspond to your primary ISP's hostname rather than being your first name. As an example, if your primary email address is...
daffy.duck @ waltdisney.com
...then your machine's hostname should be...
waltdisney.com
...and your username on that system should be...
daffy.duck
...and I'm sure you can substitute whatever is relevant for your actual email address in that.
As per my last email, you need to tweak the HOSTNAME= line in the file /etc/sysconfig/network to contain the correct domain name, and you then need to reboot your system for this line to take effect.
Quoted 6 lines
Quoted 3 lines
Incidentally, sendmail normally tries to send all outgoing emails direct to the relevant delivery host, so the ISP you're dialled up with should make no difference at all.
That what I always thought and it always worked since RH5.2 w/o me doing anything.
The headers from your email confirm that it is doing precicely as stated here, so you do not need to worry about this.
Quoted 6 lines
Quoted 3 lines
Also please mention which MTA you are using (either look for something listening on port 25 or find the smtp entry in
/etc/inetd.conf, depending on which way your system is set up)The file inetd.conf was absent. I found it as inetd.cof.rpmsave and copied it to
/etc/inetd.conf. There is no smtp entry in this file.
SendMail doesn't run from /etc/inetd.conf so you won't find an entry in there for it.
Quoted 2 lines
This mail should go out now with my webcard ISP and using the program exmh.
As you can see, it used the program exmh but it went out with the wrong email address for you.
Best wishes from Riley.
-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs
Query regarding linking...
Hi All,
While on the topic of linking, could anyone tell me why a C source file compiles alright, but gives "Symbol not found" errors during linking? I mean, how is the error, "symbol _ABC not found" different from "function xyz not found"?
Regards,
Abhijit.
__________________________________________________
Do You Yahoo!?
HotJobs - Search Thousands of New Jobs
http://www.hotjobs.com
-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs